Unisphere-Data-MPLS-MIB
214 objects
The MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations.
Imported Objects
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TEXTUAL-CONVENTION TruthValue |
| Unisphere-Data-MIBs | usDataMibs |
| Unisphere-Data-TC | UsdNextIfIndex |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4874.2.2.54 | IdentityusdMplsMIB | The MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Globa… | ||
| 1.3.6.1.4.1.4874.2.2.54.1 | NodeusdMplsObjects | |||
| 1.3.6.1.4.1.4874.2.2.54.1.1 | NodeusdMplsLsrGlobalConfig | |||
| 1.3.6.1.4.1.4874.2.2.54.1.1.1 | NodeusdMplsGroup | |||
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.1 | ScalarusdMplsGroupMplsEnable | read-write | current | Enables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled expli… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.2 | ScalarusdMplsGroupReopTimer | read-write | current | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in tim… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.3 | ScalarusdMplsGroupLabelRangeLow | read-write | current | The lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only plat… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.4 | ScalarusdMplsGroupLabelRangeHigh | read-write | current | The higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only pla… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.5 | ScalarusdMplsGroupLspRetryTimesNoroute | read-write | current | This object configures the number of retries for LSP setup after a failure due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.6 | ScalarusdMplsGroupLspRetryIntervalNoroute | read-write | current | This object configures the time interval between two successive LSP setup retries after a failure due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.7 | ScalarusdMplsGroupLspRetryTimes | read-write | current | Use this object to configure number of retries for LSP setup after a failure other than one due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.8 | ScalarusdMplsGroupLspRetryInterval | read-write | current | Use this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.9 | ScalarusdMplsGroupLdpRetryTimesNoroute | read-write | current | Use this object to configure the number of retries for LDP to setup LSP after a failure due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.10 | ScalarusdMplsGroupLdpRetryIntervalNoroute | read-write | current | Use this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.11 | ScalarusdMplsGroupLdpRetryTimes | read-write | current | Use this object to configure LSP setup retries by LDP after a failure other than one due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.12 | ScalarusdMplsGroupLdpRetryInterval | read-write | current | Use this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.13 | ScalarusdMplsGroupLdpSessionRetries | read-write | current | Use this object to configure the number of LDP session retries. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.14 | ScalarusdMplsGroupLdpSessionRetryTimer | read-write | current | Use this object to configure the time interval between two LDP session retries. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.15 | ScalarusdMplsGroupTopologyDrivenIpProfileName | read-write | current | Usually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.16 | ScalarusdMplsGroupTopologyDrivenLdpEgressIpIntf | read-write | current | This object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.17 | ScalarusdMplsGroupTopologyDrivenLdpIngressIpIntf | read-write | current | This object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.18 | ScalarusdMplsGroupTopologyDrivenLdpEgressIpIntfHostOnly | read-write | current | This object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.19 | ScalarusdMplsGroupTopologyDrivenLdpIngressIpIntfHostOnly | read-write | current | This object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.20 | ScalarusdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListType | read-write | current | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows c… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.21 | ScalarusdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListType | read-write | current | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows c… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.22 | ScalarusdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyList | read-write | current | This object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunnc… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.23 | ScalarusdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyList | read-write | current | This object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently wit… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.24 | ScalarusdMplsGroupTopologyDrivenLdp | read-write | current | LDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows t… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.25 | ScalarusdMplsGroupLspLabelDistCtrlMode | read-only | current | Some FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two … |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.26 | ScalarusdMplsGroupLdpAdvHostOnly | read-write | current | This object allows to enable/disable LDP label advertisement mode for host only LSPs. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.27 | ScalarusdMplsGroupLsrState | read-only | current | This object value displays the status of MPLS enabled LSR such as state is up or down etc. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.1.28 | ScalarusdMplsGroupReopNow | read-write | current | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the exi… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2 | NodeusdMplsGroupList | |||
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.1 | TableusdMplsGroupTargetedHelloSendTable | not-accessible | current | This table contains list of send side IP addresses for LDP targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1 | RowusdMplsGroupTargetedHelloSendEntry | not-accessible | current | Each entry represents send IP address for targeted hello message. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1 | ColumnusdMplsGroupTargetedHelloSendAddress | not-accessible | current | Configure the send side address for targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2 | ColumnusdMplsGroupLdpTargetedHelloSendMode | read-create | current | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.2 | TableusdMplsGroupTargetedHelloReceiveTable | not-accessible | current | This table contains list of receive side IP addresses for LDP targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1 | RowusdMplsGroupTargetedHelloReceiveEntry | not-accessible | current | Each entry represents receive IP address for targeted hello message. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1 | ColumnusdMplsGroupTargetedHelloReceiveAddress | not-accessible | current | Configure the receive side address for targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2 | ColumnusdMplsGroupLdpTargetedHelloReceiveMode | read-create | current | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.3 | TableusdMplsGroupLdpLabelAdverRouteListTable | not-accessible | current | Table is a list of LDP label advertisement entries. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1 | RowusdMplsGroupLdpLabelAdverRouteListEntry | not-accessible | current | Each entry represents access list pairs for the LDP peers label advertisement. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1 | ColumnusdMplsGroupLdpLabelAdverRouteListName | not-accessible | current | This LDP label advertisement route list name for which this entry contains information. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2 | ColumnusdMplsGroupLdpLabelAdverNbrListName | not-accessible | current | The LDP label advertisement neighbor route list name for which this entry contains information. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3 | ColumnusdMplsGroupLabelAdverListMode | read-create | current | This object selects the mode of addition/deletion to the list. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4 | TableusdMplsGroupLdpProfileTable | not-accessible | current | Table is a list of LDP Profile entries. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1 | RowusdMplsGroupLdpProfileEntry | not-accessible | current | Each entry represents one LDP profile settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1 | ColumnusdMplsGroupLdpProfileName | not-accessible | current | LDP profile name identifies unique entry in the table. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2 | ColumnusdMplsGroupLdpProfileHelloHoldTime | read-create | current | Configure the LDP peers hello hold time period. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3 | ColumnusdMplsGroupLdpProfileCrLdpAdminState | read-create | current | Enable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4 | ColumnusdMplsGroupLdpProfileRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5 | TableusdMplsGroupRsvpProfileTable | not-accessible | current | Table is a list of LDP Profile entries. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1 | RowusdMplsGroupRsvpProfileEntry | not-accessible | current | Each entry represents one LDP profile settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1 | ColumnusdMplsGroupRsvpProfileName | not-accessible | current | The RSVP profile name identifies unique entry in the table. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2 | ColumnusdMplsGroupRsvpProfileRefreshPeriod | read-create | current | Configure the time out period between the generation of two refresh messages. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3 | ColumnusdMplsGroupRsvpProfileCleanupTimeoutFactor | read-create | current | Confgure the number of refresh messages can be lost before PATH or RESV state is ended. |
| 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4 | ColumnusdMplsGroupRsvpProfileRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.2 | NodeusdMplsMajorLayer | |||
| 1.3.6.1.4.1.4874.2.2.54.1.2.1 | NodeusdMplsIfMajorLayer | |||
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.1 | ScalarusdMplsIfMajorNextIfIndex | read-only | current | Coordinate ifIndex value allocation for entries in the usdMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create … |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2 | TableusdMplsIfMajorTable | not-accessible | current | This table contains entries for MPLS Major interfaces present in the system. |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1 | RowusdMplsIfMajorEntry | not-accessible | current | Each entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1 | ColumnusdMplsIfMajorIndex | not-accessible | current | The ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsIfMajorNextIfInd… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2 | ColumnusdMplsIfMajorRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3 | ColumnusdMplsIfMajorLowerIfIndex | read-create | current | The ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require … |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4 | ColumnusdMplsIfMajorAdminStatus | read-create | current | Use this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for succes… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5 | ColumnusdMplsIfMajorLdpAdminStatus | read-create | current | This object enables/disables LDP admin status on the MPLS interface. |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6 | ColumnusdMplsIfMajorLdpProfileName | read-create | current | All the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7 | ColumnusdMplsIfMajorLdpVpiStart | read-create | current | This object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of inte… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8 | ColumnusdMplsIfMajorLdpVpiStop | read-create | current | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of inter… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9 | ColumnusdMplsIfMajorLdpVciStart | read-create | current | This object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of inte… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10 | ColumnusdMplsIfMajorLdpVciStop | read-create | current | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of inter… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11 | ColumnusdMplsIfMajorRsvpAdminStatus | read-create | current | This object configures RSVP admin status for MPLS interface. |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12 | ColumnusdMplsIfMajorRsvpProfileName | read-create | current | All the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by usin… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13 | ColumnusdMplsIfMajorRsvpVpiStart | read-create | current | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of int… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14 | ColumnusdMplsIfMajorRsvpVpiStop | read-create | current | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of inte… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15 | ColumnusdMplsIfMajorRsvpVciStart | read-create | current | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of int… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16 | ColumnusdMplsIfMajorRsvpVciStop | read-create | current | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of inte… |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17 | ColumnusdMplsIfMajorLabelSpaceType | read-only | current | Displays the label space type for the MPLS interface. |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18 | ColumnusdMplsIfMajorOpState | read-only | current | This object displays MPLS major interface operation state. |
| 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19 | ColumnusdMplsIfMajorCrLdpAdminState | read-only | current | This object displays the admin state of CR-LDP. |
| 1.3.6.1.4.1.4874.2.2.54.1.3 | NodeusdMplsMinorLayer | |||
| 1.3.6.1.4.1.4874.2.2.54.1.3.1 | NodeusdMplsIfMinorLayer | |||
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.1 | ScalarusdMplsIfMinorNextIfIndex | read-only | current | Coordinates ifIndex value allocation for entries in the usdMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2 | TableusdMplsIfMinorTable | not-accessible | current | This table contains entries for MPLS Minor interfaces present in the system. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1 | RowusdMplsIfMinorEntry | not-accessible | current | Each entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/delete… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1 | ColumnusdMplsIfMinorIndex | not-accessible | current | The ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsMinorNextIfIndex. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2 | ColumnusdMplsIfMinorRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3 | ColumnusdMplsIfMinorLowerIfIndex | read-only | current | The ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created wit… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4 | ColumnusdMplsIfMinorAdminStatus | read-create | current | With this object minor interface admin status can be enabled/disabled. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5 | ColumnusdMplsIfMinorEndpointAddress | read-create | current | This object configures the IP address of the tunnel destination. This object can be set along with the usdMplsIfMinorEndpointDstMask to configure the tunnel de… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6 | ColumnusdMplsIfMinorEndpointDstMask | read-create | current | This object configures the tunnel destination mask. It can be set along with the usdMplsIfMinorEndpointAddress. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7 | ColumnusdMplsIfMinorTunnelMetricMode | read-create | current | Select the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, usdMplsIfMinorRelativeTunnelMet… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8 | ColumnusdMplsIfMinorAbsoluteTunnelMetric | read-create | current | This object allows configuration of absolute metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9 | ColumnusdMplsIfMinorRelativeTunnelMetric | read-create | current | This object allows configuration of relative metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10 | ColumnusdMplsIfMinorLabelDistProto | read-create | current | This object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11 | ColumnusdMplsIfMinorAnnounceToOspf | read-create | current | This object allows to register LSP endpoints to OSPF to next hop calculation. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12 | ColumnusdMplsIfMinorAnnounceToIsis | read-create | current | This object allows to register LSP endpoints to IS-IS for next hop calculation. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13 | ColumnusdMplsIfMinorAnnounceToBgp | read-create | current | This object allows to register LSP endpoints to BGP for next hop calculation. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14 | ColumnusdMplsIfMinorBandwidth | read-create | current | This object allows configuration of bandwidth requirements for the tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15 | ColumnusdMplsIfMinorAffinity | read-create | current | This object allows configuration of resource class affinity for the tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16 | ColumnusdMplsIfMinorAffinityMask | read-create | current | This allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17 | ColumnusdMplsIfMinorSetupPriority | read-create | current | This object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18 | ColumnusdMplsIfMinorHoldingPriority | read-create | current | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priorit… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19 | ColumnusdMplsIfMinorTunnelName | read-create | current | This object allows configuration of the tunnel name to be associated with tunnel settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20 | ColumnusdMplsIfMinorTunnelRetryTimes | read-create | current | This object allows configuration of the number of retries for tunnel setup. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21 | ColumnusdMplsIfMinorTunnelRetryInterval | read-create | current | This object allows configuration of retry interval for tunnel setup. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22 | ColumnusdMplsIfMinorTunnelRetryTimesNoroute | read-create | current | This object allows configuration of the tunnel retries when no route notifications are received. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23 | ColumnusdMplsIfMinorTunnelRetryIntervalNoroute | read-create | current | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24 | ColumnusdMplsIfMinorBaseTunnelName | read-create | current | This object allows configuration of the base tunnel name over which all the tunnels are stacked over. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25 | ColumnusdMplsIfMinorVpnOuiNumber | read-create | current | This object allows configuration of the OUI part of VPN ID. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26 | ColumnusdMplsIfMinorVpnIndex | read-create | current | This object allows configuration of the index part of VPN ID. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27 | ColumnusdMplsIfMinorTunnelOpState | read-only | current | This object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged :… |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28 | ColumnusdMplsIfMinorTargetedDynamicTunnel | read-create | current | Configure targeted dynamic tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29 | ColumnusdMplsIfMinorReoptimization | read-create | current | Configure tunnel reoptimization. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2 | NodeusdMplsMinorLayerList | |||
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1 | TableusdMplsIfMinorPathOptionTable | not-accessible | current | Table is a list of different LSP paths as option for each LSP setup. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1 | RowusdMplsIfMinorPathOptionEntry | not-accessible | current | Each entry represents one path option for the LSP. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1 | ColumnusdMplsIfMinorPathOptionIndex | not-accessible | current | Minor interface uid. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2 | ColumnusdMplsIfMinorPathOptionNumber | not-accessible | current | Unique number to identify each path option configured. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3 | ColumnusdMplsIfMinorPathOptionProtocol | read-create | current | Select the each path option explicit routing protocol. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4 | ColumnusdMplsIfMinorPathOptionLockdown | read-create | current | Enable/disable each configured path option reoptimization. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5 | ColumnusdMplsIfMinorPathOptionPathName | read-create | current | Configure the name for each path option. |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6 | ColumnusdMplsIfMinorPathOptionPathId | read-create | current | Configure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the … |
| 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7 | ColumnusdMplsIfMinorPathOptionRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.4 | NodeusdMplsTunnelProfile | |||
| 1.3.6.1.4.1.4874.2.2.54.1.4.1 | NodeusdMplsTunnelProfileGroup | |||
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1 | TableusdMplsTunnelProfileTable | not-accessible | current | Table is a list of tunnel profiles for a given VR. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1 | RowusdMplsTunnelProfileEntry | not-accessible | current | Each entry represents one tunnel profile. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1 | ColumnusdMplsTunnelProfileName | not-accessible | current | Associate a name for the configured tunnel profile settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2 | ColumnusdMplsTunnelProfileAdminStatus | read-create | current | Enable/disable the adminstatus of the tunnel profile. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3 | ColumnusdMplsTunnelProfileBaseTunnelName | read-create | current | Configure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunne… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4 | ColumnusdMplsTunnelProfileIpProfileName | read-create | current | Configures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5 | ColumnusdMplsTunnelProfileLabelDistProto | read-create | current | Configure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC bindi… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6 | ColumnusdMplsTunnelProfileAnnounceToOspf | read-create | current | Configure the routing protocol for next hop calculations as OSPF. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7 | ColumnusdMplsTunnelProfileAnnounceToIsis | read-create | current | Configure routing protocol for next hop calculations as ISIS. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8 | ColumnusdMplsTunnelProfileAnnounceToBgp | read-create | current | Configure routing protocol for next hop calculations as BGP. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9 | ColumnusdMplsTunnelProfileMetricMode | read-create | current | Select the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, usdMplsTunnelPr… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10 | ColumnusdMplsTunnelProfileAbsoluteMetric | read-create | current | This object allows configuration of the absolute metric values. Refer to usdMplsTunnelProfileMetricMode for how set it. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11 | ColumnusdMplsTunnelProfileRelativeMetric | read-create | current | This object allows configuration of the relative metric values. Refer to usdMplsTunnelProfileMetricMode for how set it. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12 | ColumnusdMplsTunnelProfileBandwidth | read-create | current | This object allows configuration of bandwidth requirements for the tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13 | ColumnusdMplsTunnelProfileAffinity | read-create | current | This object allows configuration of the resource class affinity for the tunnel. This can set independently of usdMplsTunnelProfileAffinityMask. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14 | ColumnusdMplsTunnelProfileAffinityMask | read-create | current | This allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with usdMplsTunnelProfileAffinit… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15 | ColumnusdMplsTunnelProfileSetupPriority | read-create | current | This object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16 | ColumnusdMplsTunnelProfileHoldingPriority | read-create | current | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priorit… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17 | ColumnusdMplsTunnelProfileRetryTimes | read-create | current | This object allows configuration of the number of retries for the tunnel setup. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18 | ColumnusdMplsTunnelProfileRetryInterval | read-create | current | This object allows configuration of retry interval for tunnel setup. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19 | ColumnusdMplsTunnelProfileRetryTimesNoroute | read-create | current | This object allows configuration of the tunnel retries when no route notifications are received. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20 | ColumnusdMplsTunnelProfileRetryIntervalNoroute | read-create | current | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21 | ColumnusdMplsTunnelProfileVpnOuiNumber | read-create | current | This object allows configuration of the OUI part of VPN ID. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22 | ColumnusdMplsTunnelProfileVpnIndex | read-create | current | This object allows configuration of the index part of VPN ID. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23 | ColumnusdMplsTunnelProfileRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24 | ColumnusdMplsTunnelProfileTargetedDynamicTunnel | read-create | current | Configure targeted dynamic tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2 | NodeusdMplsTunnelProfileList | |||
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1 | TableusdMplsTunnelProfilePathOptionTable | not-accessible | current | Table is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1 | RowusdMplsTunnelProfilePathOptionEntry | not-accessible | current | Each entry represents one path option for the LSP setup, configured as a part of tunnel profile settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1 | ColumnusdMplsTunnelProfileNamePathOption | not-accessible | current | Name of the path option. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2 | ColumnusdMplsTunnelProfilePathOptionNumber | not-accessible | current | Unique identifier for the path option. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3 | ColumnusdMplsTunnelProfilePathOptionProtocol | read-create | current | Path selection option protocol. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4 | ColumnusdMplsTunnelProfilePathOptionLockdown | read-create | current | Enable/disable path selection option reoptimization. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5 | ColumnusdMplsTunnelProfilePathOptionPathName | read-create | current | Associate a name with each explicit path. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6 | ColumnusdMplsTunnelProfilePathOptionPathId | read-create | current | Each explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7 | ColumnusdMplsTunnelProfilePathOptionRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2 | TableusdMplsTunnelProfileDynamicEndpointTable | not-accessible | current | This table contains entries for the dynamic endpoints configured for each tunnel profile. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1 | RowusdMplsTunnelProfileDynamicEndpointEntry | not-accessible | current | Dynamic endpoint entries for each tunnel profile. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1 | ColumnusdMplsTunnelProfileNameDynamicEndpoint | not-accessible | current | Configure the tunnel dynamic endpoint in tunnel profile settings. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2 | ColumnusdMplsTunnelProfileDynamicEndpointType | not-accessible | current | Configure the dynamic endpoint type for the tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3 | ColumnusdMplsTunnelProfileDynamicEndpointPolicyListType | not-accessible | current | This object allows configuration of the dynamic tunnel policy type selection. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4 | ColumnusdMplsTunnelProfileDynamicEndpointListName | not-accessible | current | This object allows configuration of the dynamic endpoints access list name. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5 | ColumnusdMplsTunnelProfileDynamicEndpointRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3 | TableusdMplsTunnelProfileTunnelEndpointTable | not-accessible | current | Table contains list of tunnel static enpoints configured for each tunnel profile. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1 | RowusdMplsTunnelProfileTunnelEndpointEntry | not-accessible | current | Each entry represents one static endpoint configuration for the tunnel. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1 | ColumnusdMplsTunnelProfileNameTunnelEndpoint | not-accessible | current | This object configures the tunnel profile name. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2 | ColumnusdMplsTunnelProfileTunnelEndpointAddress | not-accessible | current | This object configures the IP address of the tunnel destination. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3 | ColumnusdMplsTunnelProfileTunnelEndpointDstMask | not-accessible | current | This object configures the tunnel destination mask. |
| 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4 | ColumnusdMplsTunnelProfileTunnelEndpointRowStatus | read-create | current | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndG… |
| 1.3.6.1.4.1.4874.2.2.54.1.5 | NodeusdMplsExplicitPath | |||
| 1.3.6.1.4.1.4874.2.2.54.1.5.1 | NodeusdMplsExplicitPathGroup | |||
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.1 | TableusdMplsExplicitPathTable | not-accessible | current | Table is a list of hops configurations for explicit paths. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1 | RowusdMplsExplicitPathEntry | not-accessible | current | Each entry represents one hop configuration for the particular explicit path. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1 | ColumnusdMplsExplicitPathName | not-accessible | current | Configure the name for the explicit path used as table index. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2 | ColumnusdMplsExplicitPathAdminState | read-create | current | Enable/disable explicit path adminstatus. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3 | ColumnusdMplsExplicitPathRowStatus | read-create | current | Creation/deletion of the explicit path is done through setting this object. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2 | TableusdMplsExplicitPathNodeTable | not-accessible | current | Table is a list of configured explicit paths. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1 | RowusdMplsExplicitPathNodeEntry | not-accessible | current | Each entry represents one hop in a particular explicit path. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1 | ColumnusdMplsExplicitPathNodeName | not-accessible | current | Configure the name for the explicit path used in the table index. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2 | ColumnusdMplsExplicitPathNodeIndexNumber | not-accessible | current | Each explicit path hop will have an index associated with it. Configure each path hop index using this object. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3 | ColumnusdMplsExplicitPathNodeLoose | read-create | current | Configure the explicit path hop as strict or loose. Set along with HopAddress. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4 | ColumnusdMplsExplicitPathNodeHopAddress | read-create | current | Configure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the exis… |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5 | ColumnusdMplsExplicitPathNodeHopAddressMask | read-create | current | Configure the hop IP address mask. Set along with hop address. |
| 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6 | ColumnusdMplsExplicitPathNodeRowStatus | read-create | current | Use this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node se… |
| 1.3.6.1.4.1.4874.2.2.54.2 | NodeusdMplsConformance | |||
| 1.3.6.1.4.1.4874.2.2.54.2.1 | NodeusdMplsCompliances | |||
| 1.3.6.1.4.1.4874.2.2.54.2.1.1 | ComplianceusdMplsCompliance | obsolete | Obsolete compliance statement for entities which implement the Unisphere MPLS MIB. This statement became obsolete when RowStatus support was added to some of t… | |
| 1.3.6.1.4.1.4874.2.2.54.2.1.2 | ComplianceusdMplsCompliance2 | current | The compliance statement for entities which implement the Unisphere MPLS MIB. | |
| 1.3.6.1.4.1.4874.2.2.54.2.2 | NodeusdMplsConfGroups | |||
| 1.3.6.1.4.1.4874.2.2.54.2.2.1 | GroupusdMplsLsrGlobalConfGroup | current | A collection of objects providing management of MPLS label switching routers (LSRs) in a Unisphere product. | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.2 | GroupusdMplsMajorLayerConfGroup | current | A collection of objects providing management of major MPLS interfaces in a Unisphere product. | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.3 | GroupusdMplsMinorLayerConfGroup | obsolete | Obsolete collection of objects providing management of minor MPLS (tunnel) in a Unisphere product. This group became obsolete when the usdMplsIfMinorPathOption… | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.4 | GroupusdMplsTunnelProfileConfGroup | obsolete | Obsolete collection of objects providing management of MPLS tunnel profiles in a Unisphere product. This group became obsolete when the objects usdMplsTunnelPr… | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.5 | GroupusdMplsExplicitPathConfGroup | current | A collection of objects providing management of MPLS explicit paths in a Unisphere product. | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.6 | GroupusdMplsMinorLayerConfGroup2 | current | A collection of objects providing management of minor MPLS (tunnel) interfaces in a Unisphere product. | |
| 1.3.6.1.4.1.4874.2.2.54.2.2.7 | GroupusdMplsTunnelProfileConfGroup2 | current | A collection of objects providing management of MPLS tunnel profiles in a Unisphere product. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| UsdMajorCfgVciRanges | Integer32 (33..65535) | current | Generic VCI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP). |
| UsdMajorCfgVpiRanges | Integer32 (0..255) | current | Generic VPI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP). |
| UsdMinorCfgBWRanges | Unsigned32 | current | Specifies bandwidth requirements for each MPLS tunnel. |
| UsdMinorCfgHoldingAndSetupPriorityRanges | Integer32 (0..7) | current | Each LSP has a setup and hold priority before setting it up or preempting it relative to the other LSPs. This convention specifies those ranges. |
| UsdMinorCfgRetryIntervalAndNorouteRanges | Integer32 (0..60) | current | RSVP/LDP will have time interval between two successive retries for setting up tunnel successfully. This value specifies the interval ranges for LDP/RSVP with or without no-route notification. |
| UsdMinorCfgRetryTimesAndNorouteRanges | Integer32 (0..65535) | current | RSVP/LDP will have a number of retries for successfully setting up a tunnel. This value specifies retry value ranges for LDP/RSVP with or without no-route notification. |
| UsdProfileCfgBWRanges | Unsigned32 | current | Bandwidth range specified for each tunnel in tunnel profiling. |
| UsdProfileCfgHoldingAndSetupPriorityRanges | Integer32 (0..7) | current | Tunnel setup and hold priority range specified for each tunnel in tunnel profile configuration. |
| UsdProfileCfgRetryIntervalAndNorouteRanges | Integer32 (0..60) | current | Range specified for retry interval for tunnel with or without no-route notification for RSVP/LDP. |
| UsdProfileCfgRetryTimesAndNorouteRanges | Integer32 (0..65535) | current | Range specified for number of retries for tunnel with or without no-route notification for RSVP/LDP. |