VERILINK-ENTERPRISE-NCMIMUX-MIB
51 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.321.1.3030.7000 | TablencmimuxConfigTable | not-accessible | mandatory | The IMUX Configuration table. |
| 1.3.6.1.4.1.321.1.3030.7000.1 | RowncmimuxConfigEntry | not-accessible | mandatory | An entry in the ncm IMUX Configuration table. |
| 1.3.6.1.4.1.321.1.3030.7000.1.1 | ColumnncmimuxNIDConfigIndex | read-only | mandatory | This variable indicates the node id value of the node. |
| 1.3.6.1.4.1.321.1.3030.7000.1.2 | ColumnncmimuxLineIndex | read-only | mandatory | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same valu… |
| 1.3.6.1.4.1.321.1.3030.7000.1.3 | ColumnncmimuxEndId | read-only | mandatory | This value for this object indicates which end of the equipment it is accessing. |
| 1.3.6.1.4.1.321.1.3030.7000.1.4 | ColumnncmimuxIfIndex | read-only | mandatory | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.321.1.3030.7000.1.5 | ColumnncmimuxBkplaneBusSelect | read-write | mandatory | This object only has signifiance for IMUX 2164. This variable specifies which IMUX line(s) is used, and which backplane bus is assigned to which line(s). The p… |
| 1.3.6.1.4.1.321.1.3030.7000.1.6 | ColumnncmimuxCarrierLineRate | read-write | mandatory | This variable specifies whether the carrier line rate is T1 or carrier line is E1. |
| 1.3.6.1.4.1.321.1.3030.7000.1.7 | ColumnncmimuxCarrierLinesEqp | read-write | mandatory | This variable indicates the inverse multiplexer carrier lines equipped. One bit per line. Here each bit in this byte represents one of the eight carrier lines … |
| 1.3.6.1.4.1.321.1.3030.7000.1.8 | ColumnncmimuxChanneling | read-write | mandatory | This variable indicates the inverse multiplexer mode for T1 which by default is set to 64 Kbps and when the field is set to (1) the 56 kbps mode is selected. |
| 1.3.6.1.4.1.321.1.3030.7000.1.9 | ColumnncmimuxDTEClkTransmit | read-write | mandatory | This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverte… |
| 1.3.6.1.4.1.321.1.3030.7000.1.10 | ColumnncmimuxDTEClkRecv | read-write | mandatory | This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverte… |
| 1.3.6.1.4.1.321.1.3030.7000.1.11 | ColumnncmimuxDTEClkRefern | read-write | mandatory | This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverte… |
| 1.3.6.1.4.1.321.1.3030.7000.1.12 | ColumnncmimuxDTEMode | read-write | mandatory | This variable represents the DTE mode of the ncmimux |
| 1.3.6.1.4.1.321.1.3030.7000.1.13 | ColumnncmimuxDSR | read-write | mandatory | This variable represents Data Set Ready for the ncmimux which could be set for all interfaces. |
| 1.3.6.1.4.1.321.1.3030.7000.1.14 | ColumnncmimuxTM | read-write | mandatory | This variable represents Test Mode for the ncmimux which could be set for all interfaces. |
| 1.3.6.1.4.1.321.1.3030.7000.1.15 | ColumnncmimuxCTS | read-write | mandatory | This variable represents Clear To Send for the ncmimux which could be set for only V.35, EI530 and RS449 interfaces. |
| 1.3.6.1.4.1.321.1.3030.7000.1.16 | ColumnncmimuxDCD | read-write | mandatory | This variable represents Data Carrier Detect for the ncmimux which could be set for only V.35, EI530 and RS449 interfaces. |
| 1.3.6.1.4.1.321.1.3030.7000.1.17 | ColumnncmimuxRI | read-write | mandatory | This variable represents Ring Indicator for the ncmimux which could be set for only V.35 interfaces. |
| 1.3.6.1.4.1.321.1.3030.7000.1.18 | ColumnncmimuxSnapType | read-only | mandatory | This variable represents the snap type for the ncmimux |
| 1.3.6.1.4.1.321.1.3030.7000.1.19 | ColumnncmimuxQuadSlot | read-write | mandatory | This variable represents the DTE control mode of the ncmimux |
| 1.3.6.1.4.1.321.1.3030.7001 | TablencmimuxStatusTable | not-accessible | mandatory | The IMUX Status table. |
| 1.3.6.1.4.1.321.1.3030.7001.1 | RowncmimuxStatusEntry | not-accessible | mandatory | An entry in the IMUX Status table. |
| 1.3.6.1.4.1.321.1.3030.7001.1.1 | ColumnncmimuxNIDStatusIndex | read-only | mandatory | This variable indicates the node id value of the node. |
| 1.3.6.1.4.1.321.1.3030.7001.1.2 | ColumnncmimuxStatusIndex | read-only | mandatory | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same valu… |
| 1.3.6.1.4.1.321.1.3030.7001.1.3 | ColumnncmimuxStatEndId | read-only | mandatory | This value for this object indicates which end of the equipment it is accessing. |
| 1.3.6.1.4.1.321.1.3030.7001.1.4 | ColumnncmimuxLinesEqp | read-only | mandatory | This variable indicates the inverse multiplexer carrier lines equipped. One bit per line. Here each bit in this byte represents one of the eight carrier lines … |
| 1.3.6.1.4.1.321.1.3030.7001.1.5 | ColumnncmimuxLinesStat | read-only | mandatory | This represents the lines active equivalent in tabs message, indicating when a carrier line has been allocated for use by the ncmimux. (Loop integrity must be … |
| 1.3.6.1.4.1.321.1.3030.7001.1.6 | ColumnncmimuxFrameStatus | read-only | mandatory | This variable indicates the ncmimux frame structure is transmitted over each carrier line that has been allocated for use by the ncmimux. This field indicates … |
| 1.3.6.1.4.1.321.1.3030.7001.1.7 | ColumnncmimuxCTSStatus | read-only | mandatory | This variable indicates Clear To Send status that is encoded into the ncmimux frame structure on each carrier line to indicate that the integrity of the incomi… |
| 1.3.6.1.4.1.321.1.3030.7001.1.8 | ColumnncmimuxCRCStatus | read-only | mandatory | This variable represents the crc error of the incoming frame structure corresponding to a Carrier Line. |
| 1.3.6.1.4.1.321.1.3030.7001.1.9 | ColumnncmimuxFarEndCRCStatus | read-only | mandatory | This variable represents the crc error of the incoming frame structure received at the far end of the corresponding Carrier Lines. |
| 1.3.6.1.4.1.321.1.3030.7001.1.10 | ColumnncmimuxDataValidStatus | read-only | mandatory | This variable represents the data valid of the Carrier Lines. |
| 1.3.6.1.4.1.321.1.3030.7001.1.11 | ColumnncmimuxNetworkAlarm | read-only | mandatory | The value for this object indicates the front panel LED alarm status for the network interface. |
| 1.3.6.1.4.1.321.1.3030.7001.1.12 | ColumnncmimuxAlarmLED | read-only | mandatory | The value for this object indicates the front panel LED alarm status for the IMux. |
| 1.3.6.1.4.1.321.1.3030.7001.1.13 | ColumnncmimuxEventMessages | read-only | mandatory | The value for this object indicates the number of event messages in the event queue. The event queue is a list of state changes which are time-stamped and reco… |
| 1.3.6.1.4.1.321.1.3030.7002 | TablencmimuxControlTable | not-accessible | mandatory | The IMUX Control table. |
| 1.3.6.1.4.1.321.1.3030.7002.1 | RowncmimuxControlEntry | not-accessible | mandatory | An entry in the IMUX Control table. |
| 1.3.6.1.4.1.321.1.3030.7002.1.1 | ColumnncmimuxNIDControlIndex | read-only | mandatory | This variable indicates the node id value of the node. |
| 1.3.6.1.4.1.321.1.3030.7002.1.2 | ColumnncmimuxControlIndex | read-only | mandatory | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same valu… |
| 1.3.6.1.4.1.321.1.3030.7002.1.3 | ColumnncmimuxCntEndId | read-only | mandatory | This value for this object indicates which end of the equipment it is accessing. |
| 1.3.6.1.4.1.321.1.3030.7002.1.4 | ColumnncmimuxLoopback | read-write | mandatory | This variable represents the Loopback status of Imux, ELB or PLB i.e., Equipment Loop back or Payload loop back. |
| 1.3.6.1.4.1.321.1.3030.7002.1.5 | ColumnncmimuxAISPattern | read-write | mandatory | This refers to the AIS test pattern initiated |
| 1.3.6.1.4.1.321.1.3030.7002.1.6 | ColumnncmimuxTestPattern | read-only | mandatory | This refers to the test pattern initiated |
| 1.3.6.1.4.1.321.1.3030.7003 | TablencmimuxDTEStatTable | not-accessible | mandatory | The IMUX DTE Status table. |
| 1.3.6.1.4.1.321.1.3030.7003.1 | RowncmimuxDTEStatEntry | not-accessible | mandatory | An entry in the IMUX DTEStatus table. |
| 1.3.6.1.4.1.321.1.3030.7003.1.1 | ColumnncmimuxNIDDTEStatIndex | read-only | mandatory | This variable indicates the node id value of the node. |
| 1.3.6.1.4.1.321.1.3030.7003.1.2 | ColumnncmimuxDTEStatIndex | read-only | mandatory | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same valu… |
| 1.3.6.1.4.1.321.1.3030.7003.1.3 | ColumnncmimuxDTEStatReg | read-only | mandatory | This object reports the contents of the DTE Status Register as read from the IMUX hardware. |
| 1.3.6.1.4.1.321.1.3030.7003.1.4 | ColumnncmimuxDTEStatLPBK | read-only | mandatory | This object reports the DTE Pattern and Loopback Code Register Status. (0) indicates that a Loop Up Code was detected. (1) indicates that Data Pattern or Loop … |
| 1.3.6.1.4.1.321.1.3030.7003.1.5 | ColumnncmimuxDTEStatAlarm | read-only | mandatory | This object reports the front panel alarm LED status for the DTE interface. |