VOICE-OPT-MIB
239 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises Gauge |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.449 | Nodecodex | |||
| 1.3.6.1.4.1.449.2 | NodecdxProductSpecific | |||
| 1.3.6.1.4.1.449.2.1 | Nodecdx6500 | |||
| 1.3.6.1.4.1.449.2.1.2 | Nodecdx6500Configuration | |||
| 1.3.6.1.4.1.449.2.1.2.1 | Nodecdx6500CfgProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1 | Nodecdx6500PCTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.25 | Nodecdx6500PCTVoicePortTable | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1 | Tablecdx6500PPCTVoicePortTable | not-accessible | mandatory | This table contains the port configuration parameters to configure the DSPM/E&M, DSPM/FXS, DSPM/HC, and DSPM/SM. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1 | Rowcdx6500PPCTVoicePortEntry | not-accessible | mandatory | A Voice Port Configuration Table Entry. Each entry contains the configuration parameters for a single Voice Port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.1 | Columncdx6500VoiceCfgPortNumber | read-only | mandatory | Port number of the Voice port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.2 | Columncdx6500VoiceCfgPortType | read-only | mandatory | This parameter represents the port type of the port. voice :This is a voice port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.3 | Columncdx6500VoiceCfgInterfaceType | read-only | mandatory | Select one of the following physical interfaces being used for this port. The entry must match the hardware. eAndM2 :2 wire E&M (Ear and Mouth) Interface. eAnd… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.4 | Columncdx6500VoiceCfgSignalingType | read-only | mandatory | Select the E&M signalling type. i : EandMTypeI. ii : EandMTypeII. v : EandMTypeV. iii : EandMTypeIII. nc : Skipped during configuration. This parameter is disp… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.5 | Columncdx6500VoiceCfgELeadFilter | read-only | mandatory | Selection for E lead filter enable or disable option. disabled : Disables E-lead filter. enabled : Enables E-lead filter. nc : Skipped during configuration. Th… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.6 | Columncdx6500VoiceCfgHybridFXS | read-only | mandatory | Hybrid balance filters and termination type based on country. sixHundred : 600 ohm interface for USA, Japan and Ireland. canada : 600 ohms with 2.16 uF germany… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.7 | Columncdx6500VoiceCfgHybridEAndM2 | read-only | mandatory | Hybrid balance filters and termination type based on country. (Only for E&M-2wire interfaces.) sixHundred : 600 ohm interface for USA, Japan and Ireland. germa… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.8 | Columncdx6500VoiceCfgSignalingMode | read-only | mandatory | Select the voice signalling mode. normal : Allows signalling to pass end to end and signalling will be used to control circuit state and packet flow. none : A … |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.9 | Columncdx6500VoiceCfgSignalingControl | read-only | mandatory | Select signaling control transmission mode in E&M interface type. immediate : Digits are transmitted immediately. wink : Digits are transmitted after the WINK … |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.10 | Columncdx6500VoiceCfgNoOfDigitsToCollect | read-only | deprecated | Select number of digits to collect before making a call. The parameter will not be supported. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.11 | Columncdx6500VoiceCfgNoOfRings | read-only | mandatory | Number of rings to be received before a call can be accepted. This parameter is displayed for FXO and skipped for E&M and FXS interface types. A value of 0 imp… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.12 | Columncdx6500VoiceCfgPCMMode | read-only | mandatory | Select the PCM encoder/decoder mode. aLaw :PCM encoder/decoder mode = A Law. muLaw :PCM encoder/decoder mode = Mu Law. nc :Skipped during configuration. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.13 | Columncdx6500VoiceCfgCompressionRate | read-only | mandatory | Select the voice compression rate to be used by the DSP. cD8K : 8k CVSELP c16k : 16k CVSELP cBD8K : Bundled 8k CVSELP cB16k : Bundled 16k CVSELP. cE8Kb : Enhan… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.14 | Columncdx6500VoiceCfgDSIControl | read-only | mandatory | Select if the Digital Speech Interpolation (Silence Detector) will be used with this channel. enabled : DSI is activated. disabled : DSI is not used. nc : Skip… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.15 | Columncdx6500VoiceCfgSmoothingDelay | read-only | mandatory | Select maximum inter packet arrival jitter due to network in milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.16 | Columncdx6500VoiceCfgEchoControl | read-only | mandatory | Select echo control. disabled : Echo pass through. enabled : This enables echo control logic. nc : Skipped during configuration. Echo not detected and not canc… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.17 | Columncdx6500VoiceCfgEchoReturnLoss | read-only | mandatory | Select echo return loss in dBm. minus3 : -3 dBm. minus6 : -6 dBm. minus9 : -9 dBm. minus12 : -12dBm. nc :Skipped during configuration. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.18 | Columncdx6500VoiceCfgTxInputSignalLevel | read-only | mandatory | Enter the input signal level. To be specified in steps of 0.5 dBm FXO Interface Type : 600 Ohms +6.0 to -2.5dbm 600 Ohms Adaptive +6.0 to -2.5dbm FXS Interface… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.19 | Columncdx6500VoiceCfgRxOutputSignalLevel | read-only | mandatory | Enter the output signal level. To be selected in steps of 0.5 dBm. FXO Interface Type : 600 Ohms +0.0 to -8.0dbm 600 Ohms Adaptive +0.0 to -8.0dbm FXS Interfac… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.20 | Columncdx6500VoiceCfgFaxSupport | read-only | mandatory | This parameter selects whether the FAX data is to be supported. disabled : FAX data will not be detected. enabled : Detects presence of FAX data. nc : Skipped … |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.21 | Columncdx6500VoiceCfgFaxRates | read-only | mandatory | Specify the speed to switch to, when FAX data is detected. This parameter is ignored if Fax support was disabled. fr9600 : FAX to be transmitted across the net… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.22 | Columncdx6500VoiceCfgVoiceBandDetection | read-only | mandatory | Modem data detection. yes : Detection of modem data enabled. no : Detection of modem data disabled. nc : Skipped during configuration. This parameter will be s… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.23 | Columncdx6500VoiceCfgAutoCallMnemonic | read-only | mandatory | This mnemonic name is used to originate the call. It consists of 0 - 8 alphanumeric characters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.24 | Columncdx6500VoiceCfgCallControl | read-only | mandatory | Select calling method. offhook : Call only when Offhook.Disconnect on Onhook. auto : SVC does not depend on On/Offhook condition.It remains established permane… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.25 | Columncdx6500VoiceCfgAutoCallTimeout | read-only | mandatory | Time interval between two successive calls in case of failure of previous call.Used only in `Auto' call control mode.This parameter will be skipped if Call Con… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.26 | Columncdx6500VoiceCfgCallRetries | read-only | mandatory | Enter maximum number of call retries when previous call failed.Used only in Auto Call Control mode.'0' means try forever. This parameter will be skipped if Cal… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.27 | Columncdx6500VoiceCfgGroupSubaddress | read-only | mandatory | Specifies a port subaddress that is shared by several Voice ports. Incoming calls with this subaddress are routed to one of several ports sharing this subaddre… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.28 | Columncdx6500VoiceCfgBilling | read-only | mandatory | This controls whether billing (accounting) records will be created for calls on this port. enabled : Billing is enabled. disabled : Billing is disabled. nc : S… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.29 | Columncdx6500VoiceCfgRxSignalingStateChangeFilter | read-only | mandatory | The amount of time to declare a valid supervisory signaling state change. The granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.30 | Columncdx6500VoiceCfgT1E1RxIdleOnhookState | read-only | mandatory | The signalling state that represents the idle state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. For T1 SF p… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.31 | Columncdx6500VoiceCfgT1E1TxIdleOnhookState | read-only | mandatory | The signalling state that represents the idle state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. For T1 SF p… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.32 | Columncdx6500VoiceCfgT1E1RxActiveOffhookState | read-only | mandatory | The signalling state that represents the active state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. For T1 SF… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.33 | Columncdx6500VoiceCfgT1E1TxActiveOffhookState | read-only | mandatory | The signalling state that represents the active state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. The range… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.34 | Columncdx6500VoiceCfgT1E1RingingState | read-only | mandatory | The signalling state that represents the ringing state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. For T1 S… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.35 | Columncdx6500VoiceCfgT1E1NoRingingState | read-only | mandatory | The signalling state that represents the no ringing state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface. For T… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.36 | Columncdx6500VoiceCfgRxWinkStartTimer | read-only | mandatory | This is the maximum time to wait for the beginning of the wink signal from the PBX before declaring a wink start malfunction. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.37 | Columncdx6500VoiceCfgRxMinimumReceiveWink | read-only | mandatory | The amount of time required to declare a valid wink. Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.38 | Columncdx6500VoiceCfgRxCalledEndGlareDetect | read-only | mandatory | The length of time when a wink pulse will be detected as a glare condition. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.39 | Columncdx6500VoiceCfgRxFirstDigitTimer | read-only | mandatory | The maximum time (in seconds) to wait for the first DTMF digit before declaring a `busyout' state. Granularity is 1 second. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.40 | Columncdx6500VoiceCfgRxInterdigitTimer | read-only | mandatory | This is the maximum time (in seconds) to wait for a subsequent receive digit before declaring a misdial. Granularity is 1 second. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.41 | Columncdx6500VoiceCfgTxWinkDelay | read-only | mandatory | The time delay from receiving a valid Offhook state to start transmitting a wink. Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.42 | Columncdx6500VoiceCfgTxWinkWidth | read-only | mandatory | The width of the transmitted wink pulse. Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.43 | Columncdx6500VoiceCfgTxDigitDelay | read-only | mandatory | The time delay before transmitting the first DTMF digit after a wink is received.Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.44 | Columncdx6500VoiceCfgTxDigitOn | read-only | mandatory | The time DTMF digits are transmitted. Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.45 | Columncdx6500VoiceCfgTxInterdigitTime | read-only | mandatory | The time between transmitting DTMF digits. Granularity is 10 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.46 | Columncdx6500VoiceCfgRxInterringWait | read-only | mandatory | This is the maximum time to wait for subsequent receive rings before declaring a call abandoned condition. Granularity is 1 second. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.47 | Columncdx6500VoiceCfgRxRingStateChangeFilter | read-only | mandatory | The amount of time to declare the change in the ring state. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.48 | Columncdx6500VoiceCfgTxRingerOffLong | read-only | mandatory | This timer is the long off period for ringer cadences that have a short and long off period.For the cases where the ring cadence defines one off period, the Tx… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.49 | Columncdx6500VoiceCfgTxRingerOffShort | read-only | mandatory | This timer is the short off period for ringer cadences that have a short and long off period.For the cases where the ring cadence defines one off period, the T… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.50 | Columncdx6500VoiceCfgTxRingerOn | read-only | mandatory | The time of the ringer on pulse. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.51 | Columncdx6500VoiceCfgRxDisconnectTimer | read-only | mandatory | The amount of time required to receive idle signaling to disconnect a call. For an analog FXO port, RX idle signaling is the loss of loop current. For a FXS po… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.52 | Columncdx6500VoiceCfgRxCalledEndDisconnectDelayTimer | read-only | mandatory | The additional amount of time beyond the Rx Disconnect filter the calling end must be Onhook to disconnect a call. Granularity is 1 second. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.53 | Columncdx6500VoiceCfgLineErrorRecovery | read-only | mandatory | The length of time voice will be suppressed after LOS or OF condition clears.Granularity is 10 milliseconds. This parameter will be displayed for virtual ports… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.54 | Columncdx6500VoiceCfgSignalingSampleRate | read-only | mandatory | The time between sampling received signalling states and line states.Granularity is 1 millisecond. This parameter will be displayed only when the DEBUG flag is… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.55 | Columncdx6500VoiceCfgWaitForParams | read-only | mandatory | The amount of time to wait for a message to set the parameters after receiving a disconnect message (messages occur in the form of an event) before busying out… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.56 | Columncdx6500VoiceCfgSpareTimer1 | read-only | mandatory | Spare timer number 1.Granularity is 1 millisecond.This parameter will be displayed only when the DEBUG flag is set. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.57 | Columncdx6500VoiceCfgSpareTimer2 | read-only | mandatory | Spare timer number 2.Granularity is 1 millisecond. This parameter will be displayed only when the DEBUG flag is set. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.58 | Columncdx6500VoiceCfgTxInterdigitPauseTime | read-only | mandatory | The time between transmitting DTMF digits. Enter in steps of 10 msec. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.59 | Columncdx6500VoiceCfgRxMinimumFlashHookTime | read-only | mandatory | The shortest length of time required to be onhook to be recognized as a flash-hook. This value must be less than Rx Maximum Flash-Hook Time for flash-hook to b… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.60 | Columncdx6500VoiceCfgRxMaximumFlashHookTime | read-only | mandatory | The longest length of time to be onhook to be recognized as a flash-hook. This value must be less than Rx Disconnect Timer for flash-hook to be recognized. Not… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.61 | Columncdx6500VoiceCfgTransparentSignalingIdleState | read-only | mandatory | The received signalling state that represents the idle state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface.`x'… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.62 | Columncdx6500VoiceCfgTransparentRxDisconnectFilter | read-only | mandatory | The time the received signaling state must be equal to the idle state to disconnect the voice call. Zero value disables idle state disconnect and maintains the… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.63 | Columncdx6500VoiceCfgTransparentSignalingBusyoutState | read-only | mandatory | The received signalling state that represents the Busyout state. For E1 ports and T1 ESF ports, these bits represent the ABCD signalling bits on the interface.… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.64 | Columncdx6500VoiceCfgXlateSigInfo0000FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.65 | Columncdx6500VoiceCfgXlateSigInfo1000FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.66 | Columncdx6500VoiceCfgXlateSigInfo0100FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.67 | Columncdx6500VoiceCfgXlateSigInfo1100FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.68 | Columncdx6500VoiceCfgXlateSigInfo0010FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.69 | Columncdx6500VoiceCfgXlateSigInfo1010FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.70 | Columncdx6500VoiceCfgXlateSigInfo0110FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.71 | Columncdx6500VoiceCfgXlateSigInfo1110FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.72 | Columncdx6500VoiceCfgXlateSigInfo0001FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.73 | Columncdx6500VoiceCfgXlateSigInfo1001FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.74 | Columncdx6500VoiceCfgXlateSigInfo0101FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.75 | Columncdx6500VoiceCfgXlateSigInfo1101FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.76 | Columncdx6500VoiceCfgXlateSigInfo0011FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.77 | Columncdx6500VoiceCfgXlateSigInfo1011FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.78 | Columncdx6500VoiceCfgXlateSigInfo0111FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.79 | Columncdx6500VoiceCfgXlateSigInfo1111FromRemoteToLocalPort | read-only | mandatory | Translate the signalling information received from the remote end to a value to be transmitted out the local port.If the local port is a T1/ESF or E1 port ente… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.80 | Columncdx6500VoiceCfgDialToneLowerFrequency | read-only | mandatory | The lower of the two frequencies needed to generate the dial tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.81 | Columncdx6500VoiceCfgDialToneLowerFrequencyAmplitude | read-only | mandatory | The amplitude of the lower frequency to generate the dial tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.82 | Columncdx6500VoiceCfgDialToneUpperFrequency | read-only | mandatory | The higher of the two frequencies needed to generate the dial tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.83 | Columncdx6500VoiceCfgDialToneUpperFrequencyAmplitude | read-only | mandatory | The amplitude of the upper frequency to generate the dial tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.84 | Columncdx6500VoiceCfgRingBackToneLowerFrequency | read-only | mandatory | The lower of the two frequencies needed to generate the Ringback tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.85 | Columncdx6500VoiceCfgRingBackToneLowerFrequencyAmplitude | read-only | mandatory | The amplitude of the lower frequency to generate the Ringback tone. To be specified in steps of 0.5dB, -30dB turn off output.The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.86 | Columncdx6500VoiceCfgRingBackToneUpperFrequency | read-only | mandatory | The higher of the two frequencies needed to generate the Ring-back tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.87 | Columncdx6500VoiceCfgRingBackToneUpperFrequencyAmplitude | read-only | mandatory | The amplitude of the upper frequency to generate the Ringback tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.88 | Columncdx6500VoiceCfgBusyToneLowerFrequency | read-only | mandatory | The lower of the two frequencies needed to generate the Busy tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.89 | Columncdx6500VoiceCfgBusyToneLowerFrequencyAmplitude | read-only | mandatory | The amplitude of the lower frequency to generate the Busy tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.90 | Columncdx6500VoiceCfgBusyToneUpperFrequency | read-only | mandatory | The higher of the two frequencies needed to generate the Busy tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.91 | Columncdx6500VoiceCfgBusyToneUpperFrequencyAmplitude | read-only | mandatory | The amplitude of the upper frequency to generate the Busy tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.92 | Columncdx6500VoiceCfgTxBusyToneOffTime | read-only | mandatory | Timer for the Busy tone off state. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.93 | Columncdx6500VoiceCfgTxBusyToneOnTime | read-only | mandatory | Timer for the busy tone on state. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.94 | Columncdx6500VoiceCfgFastBusyToneLowerFrequency | read-only | mandatory | The lower of the two frequencies needed to generate the Fast Busy tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.95 | Columncdx6500VoiceCfgFastBusyToneLowerFrequencyAmplitude | read-only | mandatory | The amplitude of the lower frequency to generate the Fast Busy tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dB… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.96 | Columncdx6500VoiceCfgFastBusyToneUpperFrequency | read-only | mandatory | The higher of the two frequencies needed to generate the Fast Busy tone. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.97 | Columncdx6500VoiceCfgFastBusyToneUpperFrequencyAmplitude | read-only | mandatory | The amplitude of the upper frequency to generate the Fast Busy tone. To be specified in steps of 0.5dB, -30dB turn off output. The range is from -30dBm to -3dB… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.98 | Columncdx6500VoiceCfgTxFastBusyToneOffTime | read-only | mandatory | Timer for the Fast Busy tone off state. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.99 | Columncdx6500VoiceCfgTxFastBusyToneOnTime | read-only | mandatory | Timer for the Fast Busy tone on state. Granularity is 50 milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.100 | Columncdx6500VoiceCfgHybridFXO | read-only | mandatory | Hybrid balance filters. sixHundred : 600 ohm interface. adaptive : 600 ohm with adaptive filter. nc : Skipped during configuration. This parameter is displayed… |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.101 | Columncdx6500VoiceCfgTxPulse | read-only | mandatory | The width of the transmitted Seizure, PTS, or Answer pulse in msec. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.102 | Columncdx6500VoiceCfgRxMinPulse | read-only | mandatory | The minimum pulse width to declare a valid received Seizure, PTS, or Answer pulse. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.103 | Columncdx6500VoiceCfgRxMaxPulse | read-only | mandatory | The maximum pulse width to declare a valid received Seizure, PTS, or Answer. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.104 | Columncdx6500VoiceCfgTxMasterClear | read-only | mandatory | The width of the transmitted Master Clear-Forward, Clear-Back, or Release Guard pulse in msec. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.105 | Columncdx6500VoiceCfgRxMinMasterClear | read-only | mandatory | The minimum pulse width to declare a valid received Master Clear-Forward, Clear-Back, or Release Guard. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.106 | Columncdx6500VoiceCfgRxMaxMasterClear | read-only | mandatory | The maximum pulse width to declare a valid received Master Clear-Forward, Clear-Back, or Release Guard. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.107 | Columncdx6500VoiceCfgTxSlaveClear | read-only | mandatory | The width of the transmitted Slave Clear-Forward or Clear-Back pulse in msec. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.108 | Columncdx6500VoiceCfgRxMinSlaveClear | read-only | mandatory | The minimum pulse width to declare a valid received Slave Clear-Forward or Clear-Back. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.109 | Columncdx6500VoiceCfgRxMaxSlaveClear | read-only | mandatory | The maximum pulse width to declare a valid received Slave Clear-Forward or Clear-Back. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.110 | Columncdx6500VoiceCfgTxSlaveRelease | read-only | mandatory | The width of the transmitted Slave Release Guard pulse in msec. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.111 | Columncdx6500VoiceCfgRxMinSlaveRelease | read-only | mandatory | The minimum pulse width to declare a valid received Slave Release Guard. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.112 | Columncdx6500VoiceCfgRxMaxSlaveRelease | read-only | mandatory | The maximum pulse width to declare a valid received Slave Release Guard. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.113 | Columncdx6500VoiceCfgTxPTSTime | read-only | mandatory | The time delay from receiving a valid Seizure from the PBX to start transmitting a PTS pulse. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.114 | Columncdx6500VoiceCfgRxPTSTime | read-only | mandatory | The maximum time to wait for a PTS pulse from the PBX after sending a Seizure before giving up and clearing the trunk. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.115 | Columncdx6500VoiceCfgMasterGuard | read-only | mandatory | The time the master side waits in the guard state after transmitting a clear pulse. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.116 | Columncdx6500VoiceCfgSlaveGuard | read-only | mandatory | The time the slave side waits in the guard state after transmitting a clear pulse. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.117 | Columncdx6500VoiceCfgTxFlashHookTime | read-only | mandatory | The lenght of time a flash signal will be transmitted as a result of a flash-hook from the remote interface. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.118 | Columncdx6500VoiceCfgDtmfAmplitude | read-only | mandatory | The amplitude of the DTMF digits. To be specified in steps of 0.5dB, -30.0 turn off output. The range is from -30dBm to -3dBm. |
| 1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.119 | Columncdx6500VoiceCfgFXSOffhookFilter | read-only | mandatory | This is the amoung of time a valid OFFHOOK conidtion must be present before an analog FXS will declare OFFHOOK. |
| 1.3.6.1.4.1.449.2.1.2.2 | Nodecdx6500CfgGeneralGroup | |||
| 1.3.6.1.4.1.449.2.1.2.2.21 | Nodecdx6500GCTVoiceSwitchTable | |||
| 1.3.6.1.4.1.449.2.1.2.2.21.1 | Tablecdx6500GGCTVoiceSwitchTable | not-accessible | mandatory | This table contains the Voice Switch Table configuration. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1 | Rowcdx6500VoiceSwitchEntry | not-accessible | mandatory | Each entry contains a list of parameters that makeup the Voice Switch Table. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.1 | Columncdx6500VoiceSwitchRxDTMFDigitString | read-only | mandatory | Select the voice number plans for the 6520/6560 network. The received DTMF digits received by the voice interface is compared to this parameter. - Enter a trai… |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.2 | Columncdx6500VoiceSwitchNumRxDigitToReceive | read-only | mandatory | Select the number of DTMF digits to be received before making the call request. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.3 | Columncdx6500VoiceSwitchCallParam | read-only | mandatory | Define the network address of the called node and the port or Hunt Group number of the desired destination port. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.4 | Columncdx6500VoiceSwitchAlternateDestination | read-only | deprecated | This object is no longer supported. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.5 | Columncdx6500VoiceSwitchCompressionOverrideRate | read-only | mandatory | Select the voice compression override algorithm. none - No override, use port configured value. c8k - 8k CVSELP c16k - 16k CVSELP cB8k - Bundled 8k CVSELP cB16… |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.6 | Columncdx6500VoiceSwitchNumLeadingDigitToStrip | read-only | mandatory | Select the number of leading digits to be stripped off the received digits stream before sending the digits stream to the remote port. |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.7 | Columncdx6500VoiceSwitchPreFixDigits | read-only | mandatory | Select digits to be added in front of or at the end of the received stream (after the stripped digits are removed) before sending the digit stream to the remot… |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.8 | Columncdx6500VoiceSwitchPostFixDigits | read-only | deprecated | Select DTMF digits to be added at the end of the received DTMF stream before sending the digit stream to the remote port. Range: 1 to 20 characters (valid char… |
| 1.3.6.1.4.1.449.2.1.2.2.21.1.1.9 | Columncdx6500VoiceSwitchEntryNumber | read-only | mandatory | This is the entry number in the Voice Switch Table. |
| 1.3.6.1.4.1.449.2.1.3 | Nodecdx6500Statistics | |||
| 1.3.6.1.4.1.449.2.1.3.1 | Nodecdx6500StatProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1 | Nodecdx6500PSTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.26 | Nodecdx6500PSTVoicePortTable | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1 | Tablecdx6500PPSTVoicePortTable | not-accessible | mandatory | This table contains the port statistics for Voice ports. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1 | Rowcdx6500PPSTVoicePortEntry | not-accessible | mandatory | A Voice Port Statistics Table Entry. Each entry contains the statistics for a single Voice Port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.1 | Columncdx6500VoiceStatsPortNumber | read-only | mandatory | Port number of the Voice Port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.2 | Columncdx6500VoiceStatsPortInterfaceType | read-only | mandatory | This parameter indicates the type of DPSM card used. eAndM2 : DPSM/E&M. eAndM4 : DPSM/E&M. fxo : DPSM/HC(FXO). fxs : DPSM/FXS. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.3 | Columncdx6500VoiceStatsHWRevAndPartNumber | read-only | mandatory | Hardware revision and part number of the main card. The revision number has format n.n and the part number is an 8 digit number of the form nnnnnnnn. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.4 | Columncdx6500VoiceStatsFortyEightVolts | read-only | mandatory | This parameter indicates whether the 48 volt power supply is installed in the node. none : power supply not installed. present : power supply installed. na : V… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.5 | Columncdx6500VoiceStatsPortState | read-only | mandatory | This parameter indicates ths status of the port. disabled : The port is disabled. enabled : The port is enabled. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.6 | Columncdx6500VoiceStatsCircuitState | read-only | mandatory | This parameter indicates the state of the SVC associated with this port. connected : SVC established. disconnected : SVC not established. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.7 | Columncdx6500VoiceStatsCurrentMode | read-only | mandatory | This parameter indicates the current operating mode of the DSP. voice : DSP is currently operating in voice mode. pcm : PCM mode is not supported. fax : DSP is… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.8 | Columncdx6500VoiceStatsTimeOfLastStatReset | read-only | mandatory | This parameter indicates the time since the last statistic reset using the format month:day:year:hours:minutes:seconds (mm:dd:yyyy:hh:mm:ss). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.9 | Columncdx6500VoiceStatsCallDuration | read-only | mandatory | This parameter indicates the duration of the current (last) call using the format hours:minutes:seconds (hh:mm:ss). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.10 | Columncdx6500VoiceStatsTotalCallDuration | read-only | mandatory | This parameter indicates the total time of all calls since last reset.It is measured from Offhook to Onhook and uses the format hours:minutes:seconds (hh:mm:ss… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.11 | Columncdx6500VoiceStatsPortUtilization | read-only | mandatory | This parameter is calculated as the ratio of `Total Call Duration' to `Time Of Last Reset'. It is a percentage value of the form nnn%. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.12 | Columncdx6500VoiceStatsNumberOfCalls | read-only | mandatory | This parameter indicates the total number of calls since the last reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.13 | Columncdx6500VoiceStatsLastDigitsTransmitted | read-only | mandatory | This parameter indicates the last DTMF digits transmitted to the voice interface. Not supported at this time. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.14 | Columncdx6500VoiceStatsLastDigitsReceived | read-only | mandatory | This parameter indicates the last DTMF digits received from the voice interface. Not supported at this time. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.15 | Columncdx6500VoiceStatsTxPacketDropped | read-only | mandatory | This parameter indicates the number of times transmit packets were dropped due to DSPM congestion. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.16 | Columncdx6500VoiceStatsRxPacketDropped | read-only | mandatory | This parameter indicates the number of times receive packets were dropped due to network overload or processor loading. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.17 | Columncdx6500VoiceStatsDroppedPackets | read-only | mandatory | This parameter indicates the estimate of packets dropped end to end in the network. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.18 | Columncdx6500VoiceStatsDSPInternalFaults | read-only | mandatory | This parameter indicates the number of recoverable software faults.It is displayed only when the DEBUG flag is set. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.19 | Columncdx6500VoiceStatsTxPackets | read-only | mandatory | This parameter indicates the number of packets received from the network port since the last reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.20 | Columncdx6500VoiceStatsRxPackets | read-only | mandatory | This parameter indicates the number of packets sent to the network port since the last reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.21 | Columncdx6500VoiceStatsTxPacketsPerSecond | read-only | mandatory | This parameter indicates the average number of packets transmitted per second.It is calculated as the ratio of `Tx Packets' to `Total Call Duration'. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.22 | Columncdx6500VoiceStatsRxPacketsPerSecond | read-only | mandatory | This parameter indicates the average number of packets received per second.It is calculated as the ratio of `Rx Packets' to `Total Call Duration'. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.23 | Columncdx6500VoiceStatsDSIEfficiency | read-only | mandatory | This parameter is calculated by dividing `Rx Packets/sec' by the packet rate. It is a percentage value. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.24 | Columncdx6500VoiceStatsCurrentRate | read-only | mandatory | This parameter indicates the current compression rate being used. cD8K : Compression rate is 8K. cBD8K : Compression rate is bundled 8K. cE8Kb : Compression ra… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.25 | Columncdx6500VoiceStatsInputPower | read-only | mandatory | This parameter indicates the input power level in dBm. (Measured power). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.26 | Columncdx6500VoiceStatsOutputPower | read-only | mandatory | This parameter indicates the output power level in dBm. (Measured power). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.27 | Columncdx6500VoiceStatsFAXTransmissions | read-only | mandatory | This parameter indicates the number of FAX transmissions spoofed. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.28 | Columncdx6500VoiceStatsUnsupportedFmtsFAXXmissions | read-only | mandatory | This parameter indicates the number of FAX transmissions requesting unsupported formats but transmitted using ISG formats. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.29 | Columncdx6500PPSTSignalingSequenceTrapTxState | read-only | deprecated | The transmitting voice signalling state is displayed as ABCD (i.e. 1010). This object is no longer supported. Refer to cdx6500SignalingSequenceTrapTxState. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.30 | Columncdx6500PPSTSignalingSequenceTrapRxState | read-only | deprecated | The receiving voice signalling state is displayed as ABCD (i.e. 1010). This object is no longer supported. Refer to cdx6500SignalingSequenceTrapRxState. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.31 | Columncdx6500PPSTSignalingSequenceTrapMachineState | read-only | deprecated | The voice signalling state machine state is a 11 character field representing the state of the signalling software. This object is no longer supported. Refer t… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.32 | Columncdx6500PPSTSignalingSequenceTrapTimeSinceLastChange | read-only | deprecated | This parameter indicates the time from the previous state to this state, measured in milliseconds. This object is no longer supported. Refer to cdx6500Signalin… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.33 | Columncdx6500PPSTSignalingSequenceTrapComment | read-only | deprecated | The comment field is an ASCII string upto 16 characters long. This object is no longer supported. Refer to cdx6500SignalingSequenceTrapComment. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.34 | Columncdx6500VoiceStatsCurrentStatus | read-only | mandatory | This is the call processing state machine status. inhibited : Current Status = Disconnected. disconnected : Current Status = Disconnected. calling : Current St… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.35 | Columncdx6500VoiceStatsLastClearCauseCode | read-only | mandatory | This parameter indicates the last clear cause code received Every code corresponds to an integer value followed by its text description in paranthesis. eg.Cons… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.36 | Columncdx6500VoiceStatsLastClearDiagnosticCode | read-only | mandatory | This parameter indicates the last clear diagnostic received.Every code corresponds to an integer value followed by its text description in paranthesis. eg.Cons… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.37 | Columncdx6500VoiceStatsLastInboundCallPacketCalledAddress | read-only | mandatory | This parameter contains the called address present in the last inbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.38 | Columncdx6500VoiceStatsLastInboundCallPacketCallingAddress | read-only | mandatory | This parameter contains the calling address present in the last inbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.39 | Columncdx6500VoiceStatsLastInboundCallPacketFacilities | read-only | mandatory | This parameter contains the facilities present in the last inbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.40 | Columncdx6500VoiceStatsLastInboundCallPacketCUD | read-only | mandatory | This parameter contains the call user data present in the last inbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.41 | Columncdx6500VoiceStatsLastOutboundCallPacketCalledAddress | read-only | mandatory | This parameter contains the called address present in the last outbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.42 | Columncdx6500VoiceStatsLastOutboundCallPacketCallingAddress | read-only | mandatory | This parameter contains the calling address present in the last outbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.43 | Columncdx6500VoiceStatsLastOutboundCallPacketFacilities | read-only | mandatory | This parameter contains the facilities present in the last outbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.44 | Columncdx6500VoiceStatsLastOutboundCallPacketCUD | read-only | mandatory | This parameter contains the call user data present in the last outbound call packet. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.45 | Columncdx6500VoiceStatsRingerStatus | read-only | mandatory | This parameter indicates the Ringer status on the board. It is displayed only for DSPM/FXS interfaces. rs25Hz : 25Hz Ringer status on board. rs50Hz : 50Hz Ring… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.46 | Columncdx6500VoiceStatsDSPMSMSlotNumber | read-only | mandatory | This parameter indicates the slot of the DSPM/SM. It is displayed only for DSPM/SM interfaces. A value of 0 indicates that this parameter is not available. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.47 | Columncdx6500VoiceStatsDSPMNumber | read-only | mandatory | This parameter indicates the DSP used for the virtual port.It is displayed only for DSPM/SM interfaces. A value of 0 indicates that this parameter is not avail… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.48 | Columncdx6500VoiceStatsT1E1PortNumber | read-only | mandatory | This is the port number of the T1 or E1 port this voice channel is on.It is displayed only for DSPM/SM interfaces. A value of 0 indicates that this parameter i… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.49 | Columncdx6500VoiceStatsTimeSlotNumber | read-only | mandatory | This parameter indicates the time slot number. It is displayed only for DSPM/SM interfaces. For multiple time slots it will be displayed as 1,2-5,.. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.50 | Columncdx6500VoiceStatsDaughterCardRevAndPartNumber | read-only | mandatory | Hardware revision and part number of the daughter card.The revision number has format n.n and the part number is an 8 digit number of the form nnnnnnnn.It is d… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.51 | Columncdx6500VoiceStatsVADEfficiency | read-only | mandatory | VAD (Voice Activity Detection) Efficiency shows you the percentage of VAD efficiency. It is displayed only for DSPM/FX interfaces. A value of 0 indicates that … |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.52 | Columncdx6500VoiceStatsMeanDelayDeviation | read-only | mandatory | This parameter shows you Mean Delay Deviation. It is displayed only for DSPM/FX interfaces. A value of 0 indicates that this parameter is not available. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.53 | Columncdx6500VoiceStatsMaxDelayDeviation | read-only | mandatory | This parameter shows you Max Delay Deviation in the way of Max Delay Deviation/Max Delay Dev Highwater. It is displayed only for DSPM/FX interfaces. A value of… |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.54 | Columncdx6500VoiceStatsPktRecResync | read-only | mandatory | This parameter shows you Receiver Resets. It is displayed only for DSPM/FX interfaces. A value of 0 indicates that this parameter is not available. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.55 | Columncdx6500VoiceCallStatsNoPacketDropped | read-only | mandatory | It is the number of dropped packet occurred during the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.56 | Columncdx6500VoiceCallStatsNoCallsDropped | read-only | mandatory | It is the number of dropped calls occurred during the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.57 | Columncdx6500VoiceCallStatsDroppedReason0 | read-only | mandatory | It is the number of dropped cause code 0, [originated by DTE; no info], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.58 | Columncdx6500VoiceCallStatsDroppedReason1 | read-only | mandatory | It is the number of dropped cause code 1, [number busy], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.59 | Columncdx6500VoiceCallStatsDroppedReason3 | read-only | mandatory | It is the number of dropped cause code 3, [invalid facility request], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.60 | Columncdx6500VoiceCallStatsDroppedReason5 | read-only | mandatory | It is the number of dropped cause code 5, [network congestion], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.61 | Columncdx6500VoiceCallStatsDroppedReason9 | read-only | mandatory | It is the number of dropped cause code 9, [out of order], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.62 | Columncdx6500VoiceCallStatsDroppedReason11 | read-only | mandatory | It is the number of dropped cause code 11, [access barred], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.63 | Columncdx6500VoiceCallStatsDroppedReason13 | read-only | mandatory | It is the number of dropped cause code 13, [not obtainable], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.64 | Columncdx6500VoiceCallStatsDroppedReason17 | read-only | mandatory | It is the number of dropped cause code 17, [remote procedure error], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.65 | Columncdx6500VoiceCallStatsDroppedReason19 | read-only | mandatory | It is the number of dropped cause code 19, [local procedure error], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.66 | Columncdx6500VoiceCallStatsDroppedReason21 | read-only | mandatory | It is the number of dropped cause code 21, [RPOA out of order], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.67 | Columncdx6500VoiceCallStatsDroppedReason33 | read-only | mandatory | It is the number of dropped cause code 33, [incompatible destination], upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.68 | Columncdx6500VoiceCallStatsDroppedReason-Rest | read-only | mandatory | It is the number of the rest of dropped cause codes upto the last 24 hours. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2 | Tablecdx6500PPSTSignalingSequenceTrapTable | not-accessible | mandatory | A table containing the Signaling Sequence Trap entries. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1 | Rowcdx6500PPSTSignalingSequenceTrapEntry | not-accessible | mandatory | An entry in the Signaling Sequence Trap table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.1 | Columncdx6500SignalingSequenceTrapPortNumber | read-only | mandatory | Port number of the Voice Port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.2 | Columncdx6500SignalingSequenceTrapEventNumber | read-only | mandatory | Event number in the Signaling Sequence Trap Entry. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.3 | Columncdx6500SignalingSequenceTrapTxState | read-only | mandatory | The transmitting voice signalling state is displayed as ABCD (i.e. 1010). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.4 | Columncdx6500SignalingSequenceTrapRxState | read-only | mandatory | The receiving voice signalling state is displayed as ABCD (i.e. 1010). |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.5 | Columncdx6500SignalingSequenceTrapMachineState | read-only | mandatory | The voice signalling state machine state is a 11 character field representing the state of the signalling software. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.6 | Columncdx6500SignalingSequenceTrapTimeSinceLastChange | read-only | mandatory | This parameter indicates the time from the previous state to this state, measured in milliseconds. |
| 1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.7 | Columncdx6500SignalingSequenceTrapComment | read-only | mandatory | The comment field is an ASCII string upto 16 characters long. |
| 1.3.6.1.4.1.449.2.1.3.4 | Nodecdx6500StatNetworkSvcsGroup | |||
| 1.3.6.1.4.1.449.2.1.3.4.4 | Tablecdx6500StatVCSTable | not-accessible | mandatory | This table is showing the Voice Call Statistics in a node that would allow a user to determine current and past perfrmance. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1 | Rowcdx6500StatVCSEntry | not-accessible | mandatory | A list of objects describing a single VCS. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.1 | Columncdx6500StatVCSIndex | read-only | mandatory | It is time position in the list of VCS's. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.2 | Columncdx6500StatVCSTime | read-only | mandatory | It is displaying the corresponding time to index in the list of VCS's. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.3 | Columncdx6500StatVCSNoPacketDropped | read-only | mandatory | It is the number of dropped packet occurred during the time. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.4 | Columncdx6500StatVCSNoCallsDropped | read-only | mandatory | It is the number of dropped calls occurred during the time. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.5 | Columncdx6500StatVCSDroppedReasons | read-only | mandatory | It is the number of 12 possible reasons from x25-causes. (Rsn0/Rsn1/Rsn3/Rsn5/Rsn9/Rsn11/Rsn13/Rsn17/Rsn19/Rsn21/Rsn33/Rsn-Rest) |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.6 | Columncdx6500StatVCSNoCallsProcessed | read-only | mandatory | It is the number of all voice calls processed. |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.7 | Columncdx6500StatVCSPercentPeakAvgCurOfCPULoad | read-only | mandatory | It is the value of Peak, Average and Currentof CPU load in percent. (Peak/Avg/Cur) |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.8 | Columncdx6500StatVCSPercentPeakAvgCurOfDataBuf | read-only | mandatory | It is the value of Peak, Average and Current of Data Buffer in percent. (Peak/Avg/Cur) |
| 1.3.6.1.4.1.449.2.1.3.4.4.1.9 | Columncdx6500StatVCSPercentPeakAvgCurOfIORBBuf | read-only | mandatory | It is the value of Peak, Average and Current of IORB Buffer in percent. (Peak/Avg/Cur) |
| 1.3.6.1.4.1.449.2.1.4 | Nodecdx6500Controls |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING | ||
| PhysicalPortNumber | INTEGER (1..54) |