WESTERMO-SW6-BRIDGE-MIB
24 objects
MIB Module for the Westermo RT-300 Radio Modem Device - Bridge definitions
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.16177.1.400.2.8 | Identityrstp | MIB Module for the Westermo RT-300 Radio Modem Device - Bridge definitions | ||
| 1.3.6.1.4.1.16177.1.400.2.8.1 | Nodeconfiguration | |||
| 1.3.6.1.4.1.16177.1.400.2.8.1.1 | NodecfgRstpBridge | |||
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.1 | ScalarcfgRstpBridgeEnabled | read-write | current | Enable RSTP on bridge. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.2 | ScalarcfgRstpBridgePriority | read-write | current | The bridge's relative priority value for determining the root bridge (the upper 16 bits of the bridge-id). A bridge with the lowest bridge-id is elected the ro… |
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.3 | ScalarcfgRstpBridgeHelloTime | read-only | current | The interval between transmissions of hello messages by designated ports, in seconds. By default the hello interval is 2 seconds. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.4 | ScalarcfgRstpBridgeForwardDelay | read-write | current | The delay used by STP bridges to transition root and designated ports to forwarding. The default value is 15. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.5 | ScalarcfgRstpBridgeMaxAge | read-write | current | The maximum age of the information transmitted by the bridge when it is the root bridge. The default value is 20. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.1.6 | ScalarcfgRstpBridgeTransmitHoldCount | read-write | current | The transmit hold count used by the port transmit state machine to limit transmission rate. The default value is 6. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2 | NodecfgRstpPort | |||
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1 | TablecfgRstpPortTable | not-accessible | current | RSTP port configuration table. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1 | RowcfgRstpPortTableEntry | not-accessible | current | RSTP port configuration table entry. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.1 | ColumncfgRstpPortIndex | not-accessible | current | Entry index of port forward table. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.2 | ColumncfgRstpPortEnabled | read-write | current | Enable RSTP on port. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.3 | ColumncfgRstpPortName | read-only | current | Port name to apply settings, e.g. eth0 or wlan0. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.4 | ColumncfgRstpPortPriority | read-write | current | The port's relative priority value for determining the root port, in multiples of 16. By default, the port priority is 0x80 (128). Any value in the lower 4 bit… |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.5 | ColumncfgRstpPortPathCost | read-write | current | The port path cost. The port's contribution, when it is the root port, to the root path cost for the bridge. By default the cost is automatically calculated fr… |
| 1.3.6.1.4.1.16177.1.400.2.8.1.2.1.1.6 | ColumncfgRstpPortAutoEdge | read-write | current | The auto edge port parameter allows the automatic detection of edge ports. Ports can be configured as edge ports to facilitate rapid changes to the forwarding … |
| 1.3.6.1.4.1.16177.1.400.2.8.10000 | Nodeconformance | |||
| 1.3.6.1.4.1.16177.1.400.2.8.10000.1 | Nodegroups | |||
| 1.3.6.1.4.1.16177.1.400.2.8.10000.1.1 | NodegroupConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.2.8.10000.1.1.1 | GroupgroupConfigRstp | current | RSTP configuration. | |
| 1.3.6.1.4.1.16177.1.400.2.8.10000.2 | Nodecompliances | |||
| 1.3.6.1.4.1.16177.1.400.2.8.10000.2.1 | Compliancecompliance | current | Implementation Requirements for DT50 bindings |