WESTERMO-SW6-FIREWALL-MIB
73 objects
MIB Module for the Westermo RT-300 Radio Modem Device - Firewall definitions
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.16177.1.400.2.1 | Identityfirewall | MIB Module for the Westermo RT-300 Radio Modem Device - Firewall definitions | ||
| 1.3.6.1.4.1.16177.1.400.2.1.1 | Nodeconfiguration | |||
| 1.3.6.1.4.1.16177.1.400.2.1.1.1 | ScalarcfgFwEnabled | read-write | current | Firewall disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2 | NodecfgFwNat | |||
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1 | TablecfgFwNatPortForwardTable | not-accessible | current | Firewall port forward rules table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1 | RowcfgFwNatPortForwardTableEntry | not-accessible | current | Firewall port forward rules table entry. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.1 | ColumncfgFwNatPrtFwdIndex | not-accessible | current | Entry index of port forward table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.2 | ColumncfgFwNatPrtFwdEnabled | read-write | current | Disable or enable the rule. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.3 | ColumncfgFwNatPrtFwdInterface | read-write | current | Name of the network interface on which the rule applies. Defines on which interface traffic is comming in. Groups of interfaces can be matched by adding the ch… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.4 | ColumncfgFwNatPrtFwdProtocol | read-write | current | Choose which IP protocol the rule matches. Allowed protocols are: * **any(0):** Any ip protocol. * **udp(1):** Only UDP protocol. * **tcp(2):** Only TCP protoc… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.5 | ColumncfgFwNatPrtFwdSourceAddress | read-write | current | Source address to match. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all inbound traffic. Set to 172.17.29.7/32 to… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.6 | ColumncfgFwNatPrtFwdSourcePortStart | read-write | current | Source start port to match. Specify the port or start of a port range from which a connection originates. Can only be used with TCP, UDP or TCP/UDP. Leave this… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.7 | ColumncfgFwNatPrtFwdSourcePortEnd | read-write | current | Destination end port to match. When matching multiple port, this value is the end of the range. Set to -1 if no range is to be matched. Can only be used with T… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.8 | ColumncfgFwNatPrtFwdDestinationAddress | read-write | current | Destination address to redirect. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all inbound traffic on the interface … |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.9 | ColumncfgFwNatPrtFwdDestinationPortStart | read-write | current | Destination start port to redirect. Specify the port or start of a port range for the destination. You can use ! to invert the sense of the rule: E.g. !80. Whe… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.10 | ColumncfgFwNatPrtFwdDestinationPortEnd | read-write | current | Destination end port to redirect. When forwarding multiple port, this value is the end of the range. Set to -1 if no range is forwarded. Can only be used with … |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.11 | ColumncfgFwNatPrtFwdRedirectDestinationAddress | read-write | current | Redirect traffic to this redirection destination address. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.1.1.12 | ColumncfgFwNatPrtFwdRedirectDestinationPort | read-write | current | Redirect traffic to this destination port. Can only be used with TCP, UDP or TCP/UDP. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2 | TablecfgFwNatOutboundTable | not-accessible | current | Firewall outbound NAT rules table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1 | RowcfgFwNatOutboundTableEntry | not-accessible | current | Firewall outbound NAT rules table entry. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.1 | ColumncfgFwNatOutIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.2 | ColumncfgFwNatOutEnabled | read-write | current | Disable or enable the rule. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.3 | ColumncfgFwNatOutInterface | read-write | current | Name of the network interface on which the rule applies. Matches traffic leaving on this interface. Needs to be set to an interface name if you are using DHCP.… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.4 | ColumncfgFwNatOutProtocol | read-write | current | Choose which IP protocol the rule matches. Allowed protocols are: * **any(0):** Any ip protocol. * **udp(1):** Only UDP protocol. * **tcp(2):** Only TCP protoc… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.5 | ColumncfgFwNatOutSourceAddress | read-write | current | Source address to match. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all inbound traffic. Set to 172.17.29.7/32 to… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.6 | ColumncfgFwNatOutSourcePortStart | read-write | current | Source start port to match. Specify the port or start of a port range from which a connection originates. Can only be used with TCP, UDP or TCP/UDP. Leave this… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.7 | ColumncfgFwNatOutSourcePortEnd | read-write | current | Destination end port to match. When matching multiple port, this value is the end of the range. Set to -1 if no range is to be matched. Can only be used with T… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.8 | ColumncfgFwNatOutDestinationAddress | read-write | current | Destination address to match. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all outbound traffic on the interface sp… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.9 | ColumncfgFwNatOutDestinationPortStart | read-write | current | Destination start port to match. Specify the port or start of a port range for the destination. Can only be used with TCP, UDP or TCP/UDP. You can use ! to inv… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.10 | ColumncfgFwNatOutDestinationPortEnd | read-write | current | Destination end port to match. When forwarding multiple port, this value is the end of the range. Set to -1 if no range is forwarded. Can only be used with TCP… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.11 | ColumncfgFwNatOutSourceRewriteAddress | read-write | current | Set the address with which outbound traffic shall be rewritten. In case you are using DHCP leave this on 0.0.0.0. **Note:** If you are not rewriting the source… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.2.2.1.12 | ColumncfgFwNatOutSourceRewritePort | read-write | current | Set the source-port with which outbound traffic shall be rewritten. Can only be used with TCP, UDP or TCP/UDP. Set to -1 to disable source port rewrite. **Note… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3 | NodecfgFwL2IpFilter | |||
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.1 | ScalarcfgFwL2IpFilterEnabled | read-write | current | Globally enable or disable the L2 IP Filter option of all Bridges. This filter will only apply on IP frames and will not touch anything else. Applies to AP and… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.2 | ScalarcfgFwL2IpFilterDefaultAction | read-write | current | Set the default action of all bridges when filtering is enabled. Take care to not lock yourself out when the default action is 'drop'. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3 | TablecfgFwL2IpFilterTable | not-accessible | current | L2 IP Filter |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1 | RowcfgFwL2IpFilterTableEntry | not-accessible | current | L2 IP Filter |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.1 | ColumncfgFwL2IpFltrIndex | not-accessible | current | Entry index of Table |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.2 | ColumncfgFwL2IpFltrEnabled | read-write | current | Rule disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.3 | ColumncfgFwL2IpFltrBridge | read-write | current | Bridge on which the rule will be applied. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.4 | ColumncfgFwL2IpFltrAction | read-write | current | Action to perform. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.5 | ColumncfgFwL2IpFltrPriority | read-write | current | Filter priority When multiple rules match, the rule with the highest priority will be applied. **NOTE:** When multiple matching rules with the same priority ex… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.6 | ColumncfgFwL2IpFltrSource | read-write | current | Filter source The source network/IP on which the rule matches (CIDR notation). Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.3.3.1.7 | ColumncfgFwL2IpFltrDestination | read-write | current | Filter destination The destination network/IP on which the rule matches (CIDR notation). Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4 | NodecfgFwFilter | |||
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.1 | ScalarcfgFwFltDefaultPolicyInput | read-write | current | The default filter policy on the input path. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.2 | ScalarcfgFwFltDefaultPolicyForward | read-write | current | The default filter policy on the forward path. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.3 | ScalarcfgFwFltDefaultPolicyOutput | read-write | current | The default filter policy on the output path. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10 | TablecfgFwFilterRulesTable | not-accessible | current | Firewall filter rules table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1 | RowcfgFwFilterRulesTableEntry | not-accessible | current | Firewall filter rules table entry. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.1 | ColumncfgFwFltRIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.2 | ColumncfgFwFltREnabled | read-write | current | Disable or enable the rule. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.3 | ColumncfgFwFltRChain | read-write | current | Action to be performed. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.4 | ColumncfgFwFltRAction | read-write | current | Action to be performed. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.5 | ColumncfgFwFltRInputInterface | read-write | current | Name of the input interface to match. Groups of interfaces can be matched by adding the character '+' at the end. E.g. eth+ to match the interfaces eth0, eth1 … |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.6 | ColumncfgFwFltROutputInterface | read-write | current | Name of the output interface to match. Groups of interfaces can be matched by adding the character '+' at the end. E.g. eth+ to match the interfaces eth0, eth1… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.7 | ColumncfgFwFltRProtocol | read-write | current | Choose which IP protocol the rule matches. For a list of the currently existing protocols see: https://en.wikipedia.org/wiki/List_of_IP_protocol_numbers Some e… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.8 | ColumncfgFwFltRSourceAddress | read-write | current | Source address to match. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all sources. Set to 172.17.29.7/32 to match t… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.9 | ColumncfgFwFltRSourcePortStart | read-write | current | Source start port to match. Specify the port or start of a port range from which a connection originates. Can only be used with tcp or udp. You can use ! to in… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.10 | ColumncfgFwFltRSourcePortEnd | read-write | current | Source end port to match. When matching multiple ports, this value is the end of the range. Can only be used with tcp or udp. Set to -1 when no range is to be … |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.11 | ColumncfgFwFltRDestinationAddress | read-write | current | Destination address to match. This can be a specific ip address or a range in CIDR notation. Set to 0.0.0.0/0 to match all destinations. Set to 172.17.29.7/32 … |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.12 | ColumncfgFwFltRDestinationPortStart | read-write | current | Destination start port to match. Specify the port or start of a port range to which a connection is going. Can only be used with tcp or udp. You can use ! to i… |
| 1.3.6.1.4.1.16177.1.400.2.1.1.4.10.1.13 | ColumncfgFwFltRDestinationPortEnd | read-write | current | Destination end port to match. When matching multiple ports, this value is the end of the range. Can only be used with tcp or udp. Set to -1 when no range is t… |
| 1.3.6.1.4.1.16177.1.400.2.1.10000 | Nodeconformance | |||
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1 | Nodegroups | |||
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1 | NodegroupConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1.1 | GroupgroupCfgFirewall | current | Firewall settings. | |
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1.2 | GroupgroupCfgFirewallPortForward | current | Firewall settings. | |
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1.3 | GroupgroupCfgFirewallOutboundNat | current | Firewall settings. | |
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1.4 | GroupgroupCfgFirewallL2IpFilter | current | Firewall settings. | |
| 1.3.6.1.4.1.16177.1.400.2.1.10000.1.1.5 | GroupgroupCfgFirewallFilter | current | Firewall settings. | |
| 1.3.6.1.4.1.16177.1.400.2.1.10000.2 | Nodecompliances | |||
| 1.3.6.1.4.1.16177.1.400.2.1.10000.2.1 | Compliancecompliance | current | Implementation Requirements for DT50 bindings |