WESTERMO-SW6-MIB
743 objects
MIB Module for the Westermo RT-300 Radio Modem Device - Base definitions
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE TimeTicks |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.16177.1.400.1 | Identitybase | MIB Module for the Westermo RT-300 Radio Modem Device - Base definitions | ||
| 1.3.6.1.4.1.16177.1.400.1.1 | Nodeconfiguration | |||
| 1.3.6.1.4.1.16177.1.400.1.1.1 | NodecfgSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.1.1.1 | ScalarcfgSysHostname | read-write | current | The hostname of the device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.1.2 | ScalarcfgSysTimezone | read-write | current | POSIX timezone string. Defines the local time. For more strings also see http://wiki.openwrt.org/doc/uci/system#time_zones **Example** Europe/Zurich: CET-1CEST… |
| 1.3.6.1.4.1.16177.1.400.1.1.2 | NodecfgNetwork | |||
| 1.3.6.1.4.1.16177.1.400.1.1.2.1 | TablecfgNetEthernetTable | not-accessible | current | Ethernet Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1 | RowcfgNetEthernetTableEntry | not-accessible | current | Ethernet Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.1 | ColumncfgNetEthIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.2 | ColumncfgNetEthName | read-only | current | Name of the ethernet interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.3 | ColumncfgNetEthEnabled | read-write | current | Ethernet interface disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.7 | ColumncfgNetEthBridge | read-write | current | If set to other than -1 the interface is part of bridge: * -1: none * 0: br0 * 1: br1 * X: brX Bridges with an index >=100 are special bridges which forward li… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.8 | ColumncfgNetEthAutoneg | read-write | current | Enables or disables auto negotiation of the PHY. * **forced(0):** Forces the speed and duplex defined by `cfgNetEthSpeed`. Only 10Mbit and 100Mbit rates are al… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.9 | ColumncfgNetEthSpeed | read-write | current | Defines a bitmask containing the possible speed/duplex combinations. * 0x01 (1) = 10Mbit/Half * 0x02 (2) = 10Mbit/Full * 0x04 (4) = 100Mbit/Half * 0x08 (8) = 1… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.10 | ColumncfgNetEthTrunk | read-write | current | This entry is active when `cfgNetEthVlanMode` is set to **trunk(0)** or **nativeuntagged(3)**. It specifies which 802.1q vlans are accepted ingress and egress … |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.11 | ColumncfgNetEthTag | read-write | current | This entry is active when `cfgNetEthVlanMode` is set to **access(1)** or **nativeuntagged(3)**. It specifies which 802.1q VLAN should be used for untagged ingr… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.12 | ColumncfgNetEthVlanMode | read-write | current | This entry specifies how the port should behave. * **trunk(0):** A trunk port carries packets on one or more specified VLANs specified in the cfgNetEthTrunk en… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.1.1.15 | ColumncfgNetEthLldpEnabled | read-write | current | When `cfgLldpEnabled` is enabled, this parameter controls if the interface takes part in LLDP operation. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2 | TablecfgNetWlanTable | not-accessible | current | WLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1 | RowcfgNetWlanTableEntry | not-accessible | current | WLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.1 | ColumncfgNetWlanIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.2 | ColumncfgNetWlanName | read-only | current | Name of the wireless interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.3 | ColumncfgNetWlanEnabled | read-write | current | Wireless interface disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.7 | ColumncfgNetWlanBridge | read-write | current | If set to other than -1 the interface is part of bridge: * -1: none * 0: br0 * 1: br1 * X: brX Bridges with an index >=100 are special bridges which forward li… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.10 | ColumncfgNetWlanTrunk | read-write | current | This entry is active when `cfgNetWlanVlanMode` is set to **trunk(0)** or **nativeuntagged(3)**. It specifies which 802.1q vlans are accepted ingress and egress… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.11 | ColumncfgNetWlanTag | read-write | current | This entry is active when `cfgNetWlanVlanMode` is set to **access(1)** or **nativeuntagged(3)**. It specifies which 802.1q VLAN should be used for untagged ing… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.12 | ColumncfgNetWlanVlanMode | read-write | current | This entry specifies how the port should behave. * **trunk(0):** A trunk port carries packets on one or more specified VLANs specified in the cfgNetWlanTrunk e… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.2.1.15 | ColumncfgNetWlanLldpEnabled | read-write | current | When `cfgLldpEnabled` is enabled, this parameter controls if the interface takes part in LLDP operation. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3 | TablecfgNetVlanTable | not-accessible | current | VLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1 | RowcfgNetVlanTableEntry | not-accessible | current | VLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.1 | ColumncfgNetVlanIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.2 | ColumncfgNetVlanName | read-only | current | Name of the VLAN interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.3 | ColumncfgNetVlanEnabled | read-write | current | VLAN interface disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.7 | ColumncfgNetVlanBridge | read-write | current | The number of the bridge the VLAN interface is applied to. VLAN interfaces are always of type access. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.8 | ColumncfgNetVlanParent | read-write | current | Name of the physical parent interface on which the VLAN resides. This entry is only active when the VLAN interface is not part of a bridge (cfgNetVlanBridge = … |
| 1.3.6.1.4.1.16177.1.400.1.1.2.3.1.9 | ColumncfgNetVlanVid | read-write | current | ID of the VLAN. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6 | TablecfgNetIpTable | not-accessible | current | IP address configuration. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1 | RowcfgNetIpTableEntry | not-accessible | current | IP address configuration. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.1 | ColumncfgNetIpIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.3 | ColumncfgNetIpEnabled | read-write | current | IP disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.4 | ColumncfgNetIpAddr | read-write | current | The IPv4 address (using CIDR notation) of the interface specified in cfgNetIpInterface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.6 | ColumncfgNetIpProto | read-write | current | This parameter defines which protocol is used to get the IPv4 settings for this interface. * **static(0):** Indicates that the address is manually configured t… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.8 | ColumncfgNetIpInterface | read-write | current | Name of the interface on which the IP resides. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.6.1.10 | ColumncfgNetIpCarpId | read-write | current | Id which references the CARP-instance by `cfgNetCarpIndex`. This parameter is only active when `cfgNetIpProto` is set to carp(5). Indicates that the referenced… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7 | TablecfgNetCarpTable | not-accessible | current | Redundant IP Addresses with the Common Address Redundancy Protocol (CARP). |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1 | RowcfgNetCarpTableEntry | not-accessible | current | Redundant IP Addresses with the Common Address Redundancy Protocol (CARP). |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.1 | ColumncfgNetCarpIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.3 | ColumncfgNetCarpEnabled | read-write | current | CARP interface disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.10 | ColumncfgNetCarpVhid | read-write | current | The Virtual Host ID. This is a unique number that is used to identify the redundancy group to other nodes in the group, and to distinguish between groups on th… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.11 | ColumncfgNetCarpPassword | read-write | current | The CARP authentication password. This is the password which is used to encrypt the CARP frames when talking to other CARP-enabled hosts in this redundancy gro… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.12 | ColumncfgNetCarpAdvbase | read-write | current | Advertisement base in seconds. This parameter specifies how often to transmit advertisement frames that we're a member of the redundancy group. This time is di… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.13 | ColumncfgNetCarpAdvskew | read-write | current | Advertisement base in 1/255th of a second. This parameter specifies how much to skew the advbase when sending CARP advertisements. By manipulating advskew, the… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.14 | ColumncfgNetCarpAdvdivider | read-write | current | Divider for `cfgNetCarpAdvbase` and `cfgNetCarpAdvskew`. This parameter specifies how much the Advbase and Advskew are divided to speed the algorithm up. With … |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.15 | ColumncfgNetCarpRatio | read-write | current | The dead ratio after which an existing master is considered dead. A slave device will wait: `cfgNetCarpRatio` * (`cfgNetCarpAdvbase` + `cfgNetCarpAdvskew`) bef… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.16 | ColumncfgNetCarpPreempt | read-write | current | Preempt other masters when the local device is better. Allow hosts within a redundancy group that have a better Advbase and Advskew to preempt the current mast… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.17 | ColumncfgNetCarpPreemptdemote | read-write | current | Preempt other master when they demote theself. Allow hosts within a redundancy group that have a better Advbase and Advskew to preempt the current master when … |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.18 | ColumncfgNetCarpLocalInterfaceGroup | read-write | current | The local carp interface group the carp interface belongs to. When `cfgNetCarpPreempt` or `cfgNetCarpPreemptdemote` is set to enabled, the interface will demot… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.19 | ColumncfgNetCarpSyncInterface | read-write | current | Name of the CARP control interface. This interface is used to transmit and receive CARP advertisements. This interface is required to have its own unique IP ad… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.7.1.21 | ColumncfgNetCarpMcastIp | read-write | current | Multicast address on which CARP advertisments are transmitted. The default multicast address for CARP is 224.0.0.18. Use this parameter to specify a custom mul… |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9 | TablecfgNetMacVlanTable | not-accessible | current | MACVLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1 | RowcfgNetMacVlanTableEntry | not-accessible | current | MACVLAN Network Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1.1 | ColumncfgNetMacVlanIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1.2 | ColumncfgNetMacVlanName | read-only | current | Name of the MACVLAN interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1.3 | ColumncfgNetMacVlanEnabled | read-write | current | MACVLAN interface disabled or enabled. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1.8 | ColumncfgNetMacVlanParent | read-write | current | Name of the parent interface on which the MACVLAN resides. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.9.1.15 | ColumncfgNetMacVlanMac | read-write | current | MAC address of the MACVLAN. Set `00:00:00:00:00:00` to use a random MAC address. **Format:** `00:14:5a:02:10:42` Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11 | TablecfgNetWwanTable | not-accessible | current | WWAN (Cellular) Network Interfaces. Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1 | RowcfgNetWwanTableEntry | not-accessible | current | WWAN (Cellular) Network Interfaces. Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1.1 | ColumncfgNetWwanIndex | not-accessible | current | Entry index of Table. Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1.2 | ColumncfgNetWwanName | read-only | current | Name of the WWAN interface Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1.3 | ColumncfgNetWwanEnabled | read-write | current | WWAN interface disabled or enabled Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1.4 | ColumncfgNetWwanPrimarySim | read-write | current | SIM parameter entry for the primary SIM This value references the `cfgCellSimIndex` of the desired entry in the `cfgCellSimTable` for the primary SIM. Applies … |
| 1.3.6.1.4.1.16177.1.400.1.1.2.11.1.5 | ColumncfgNetWwanSecondarySim | read-write | current | SIM parameter entry for the secondary SIM This value references the `cfgCellSimIndex` of the desired entry in the `cfgCellSimTable` for the secondary SIM. Appl… |
| 1.3.6.1.4.1.16177.1.400.1.1.3 | NodecfgWireless | |||
| 1.3.6.1.4.1.16177.1.400.1.1.3.1 | TablecfgWlanDeviceTable | not-accessible | current | Wireless Hardware Modules. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1 | RowcfgWlanDeviceTableEntry | not-accessible | current | Wireless Hardware Modules. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.1 | ColumncfgWlanDevIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.2 | ColumncfgWlanDevName | read-only | current | Name of the wireless device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.4 | ColumncfgWlanDevModulation | read-write | current | The modulation modes of the physical wireless device are: * **g(2):** This modulation mode uses OFDM data rates up to 54 MBit/s in the frequency band between 2… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5 | ColumncfgWlanDevBandwidth | read-write | current | Wireless Bandwidth Mode specifies the Bandwidth of the Channel. * **bw20(0):** for 20MHz wide channel. * **bw40Plus(1):** for 40MHz wide channel with the side … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.6 | ColumncfgWlanDevFrequency | read-write | current | Wireless Frequency in MHz. In AP mode, setting the wireless frequency to zero(0) enables the automatic channel selection (ACS) feature. This forces the AP to c… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8 | ColumncfgWlanDevPower | read-write | current | Max. limit for wireless output power as effective isotropic radiated power (EIRP) in dBm including array gain and antenna gain. **Note:** This parameter only l… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.10 | ColumncfgWlanDevDistance | read-write | current | Maximum distance in meters a client can be apart from the access point. Even though the distance is set in meters, the slot time settings change in 450m steps.… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.11 | ColumncfgWlanDevRts | read-write | current | Frames equal or longer in bytes than this value require a RTS/CTS handshake. RTS/CTS is used in hidden node situations. In 11bg and b mode, these frames are se… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.12 | ColumncfgWlanDevFragments | read-write | current | Frames longer in bytes than this threshold will be fragmented. Fragmentation can be used to reduce the number of retransmissions. The following settings are sp… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.13 | ColumncfgWlanDevShortRetry | read-write | current | Number of times the transmission of the RTS frame will be retried if there is no CTS received from the AP. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.14 | ColumncfgWlanDevLongRetry | read-write | current | Number of times the unicast data frames will be retried if there is no ACK from the receiver. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.15 | ColumncfgWlanDevAntennaGain | read-write | current | Antenna gain in dBi. If multiple antennas with different gains are connected, the value of the antenna with the highest gain shall be configured. Applies to AP… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.16 | ColumncfgWlanDevTxAntenna | read-write | current | Configure the number of wireless transmission antenna ports. This is a bitmask to enable/disable the chains. **Example** * 1(0001) = A1 (chain 0) enabled * 3(0… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.17 | ColumncfgWlanDevRxAntenna | read-write | current | Configure the number of wireless receiver antennas. This is a bitmask to enable/disable the chains. **Example** * 1(0001) = A1 (chain 0) enabled * 3(0011) = A1… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.18 | ColumncfgWlanDevPhy | read-only | current | The map between physical device and radio. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.24 | ColumncfgWlanDevHtCapabilities | read-write | current | HT capability flags: * [LDPC] = 1 Enable support for LDPC coding * [SHORT-GI-20] = 32 Allow short GI for 20 MHz * [SHORT-GI-40] = 64 Allow short GI for 40 MHz … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.1.1.26 | ColumncfgWlanDevQmrrString | read-write | current | A list of rate controller quadruples per queue. Each quadruple consist of (mcs-rate [0-31], tries [0-15], rts_cts [0-1], sgi [0-1]) with 4 entries per queue. 1… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2 | TablecfgWlanInterfaceTable | not-accessible | current | Wireless Virtual Interfaces. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1 | RowcfgWlanInterfaceTableEntry | not-accessible | current | Wireless Virtual Interface Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.1 | ColumncfgWlanIfaceIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.2 | ColumncfgWlanIfaceName | read-only | current | Name of the virtual wireless interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.3 | ColumncfgWlanIfaceDevice | read-write | current | Maps the virtual wireless interface to the radio device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.4 | ColumncfgWlanIfaceMode | read-write | current | Wireless Operation Mode. Allowed modes are: * **ap(0):** defines the interface as Access Point (AP) * **sta(1):** defines the interface as Station (STA) * **mo… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.5 | ColumncfgWlanIfaceSsid | read-write | current | The Service Set Identifier (SSID) of the wireless interface is the arbitrary name of the wireless network this interface is part of. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.6 | ColumncfgWlanIfaceEncryption | read-write | current | Wireless Encryption Mode. Following encryption modes are supported: **open(0)**, **wpa2(3)**, **wpa2eap(6)** and **sae(7)**. **Note:** WPA2 EAP enables 802.1X … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.7 | ColumncfgWlanIfacePassword | read-write | current | Wireless password if an encryption is in use. Each character in the pass-phrase must have an encoding in the range of 32 to 126 (decimal), inclusive. (IEEE Std… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.8 | ColumncfgWlanIfacePassiveScanning | read-write | current | Wireless Scanning Mode. If the scanning mode is set to active(0) the station will send a probe request to detect available access points if it's allowed by the… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.9 | ColumncfgWlanIfaceBeaconMiss | read-write | current | Number of misses on consecutive beacons before the station will disconnect from the associated access point. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.10 | ColumncfgWlanIfaceDtim | read-write | current | This attribute shall specify the number of beacon intervals that shall elapse between transmission of beacons frames containing a TIM element whose DTIM count … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.11 | ColumncfgWlanIfaceBitrates | read-write | current | Fixed MCS index for 802.11n rates. Set to -1 to disable (leave on auto). Allows for entering multiple indices divided by a space which are then used in auto ra… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.12 | ColumncfgWlanIfaceBeaconInterval | read-write | current | Time in kus (1.024 ms) between the sending of beacon frames. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.13 | ColumncfgWlanIfaceWmeParameter | read-write | current | Reference ID to the WME parameter table. Uses all parameters in the cfgWlanWmeTable which have as cfgWlanWmeId the value set here. Applies to AP and STA. 802.1… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.14 | ColumncfgWlanIfaceWmeEnabled | read-write | current | Enables usage of the WME parameter table. When using legacy rates (a-rates and g-rates) this is optional. When using n-rates this has to be enabled at all time… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.15 | ColumncfgWlanIfaceScanList | read-write | current | Index to specify a frequency list with frequencies to be scanned when in STA mode. To only scan the frequency defined in cfgWlanDevFrequency set to -1. To scan… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.16 | ColumncfgWlanIfaceIgnoreBroadcastSsid | read-write | current | Send empty SSID in beacons and ignore probe request frames that do not specify the full SSID, i.e., require stations to know SSID. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.17 | ColumncfgWlanIfaceMacaddrAcl | read-write | current | Mode of the MAC access control list. * **acceptunlessdeny(0):** Accept unless deny filter. Accept every MAC unless it is on the list defined in `cfgWlanAclBlac… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.18 | ColumncfgWlanIfaceMaxNumSta | read-write | current | Maximum number of allowed stations which can connect to this AP. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.19 | ColumncfgWlanIfaceBssid | read-write | current | BSSID of AP. Set 00:00:00:00:00:00 to use the MAC address stored in the flash of the wireless card itself. If this is the second virtual AP on this card it wil… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.20 | ColumncfgWlanIfaceLegacyRates | read-write | current | Wireless legacy data rates: * **11b:** 1, 2, 5.5, 11 Mbps * **11a/g:** 6, 9, 12, 18, 24, 36, 48, 54 Mbps The values are interpreted as flags: * auto(0), 1Mbps(… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.21 | ColumncfgWlanIface4addr | read-write | current | This option allows to bridge the STA side. When used on the STA, the corresponding AP has to enable this feature as well. Applies to AP and STA. 802.11n produc… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.23 | ColumncfgWlanIfaceInactivityTimeout | read-write | current | If a station does not send anything in ap_max_inactivity seconds, an empty data frame is sent to it in order to verify whether it is still in range. If this fr… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.26 | ColumncfgWlanIfaceUseVendorSsid | read-write | current | When cfgWlanIfaceIgnoreBroadcastSsid is enabled, a passively scanning STA (forced or because of DFS) has no way of detecting the AP it tries to find. On an AP … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.30 | ColumncfgWlanIfaceIeee80211w | read-write | current | Controls usage of 802.11w Management Frame Protection (MFP) mechanism. If set to optional on AP, MFP will be enabled only for clients which have it also enable… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.31 | ColumncfgWlanIfaceIeee80211wMaxTimeout | read-write | current | 802.11w Management Frame Protection (MFP) Association SA query maximum timeout (in TU = 1.024 ms; for MFP) (maximum time to wait for a SA query response) Appli… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.32 | ColumncfgWlanIfaceIeee80211wRetryTimeout | read-write | current | 802.11w Management Frame Protection (MFP) Association SA query retry timeout (in TU = 1.024 ms; for MFP) (time between two subsequent SA query requests) Applie… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.40 | ColumncfgWlanIfaceAcsList | read-write | current | Index to specify a frequency list for Automated Channel Selection (ACS) support when in AP mode. To disable set to -1. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.60 | ColumncfgWlanIfaceNeighbourReport | read-write | current | Enable/disable neighbour reporting. A STA can request the neighbour table from an AP and use this information to improve its handoff decision. Applies to AP. 8… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.61 | ColumncfgWlanIfaceNeighbourParameter | read-write | current | Reference ID to the neighbour table. Uses all neighbours in the `cfgWlanNeighbourTable` which have as `cfgWlanNeighbourId` the value set here. Applies to AP. 8… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.80 | ColumncfgWlanIfaceL2nat | read-write | current | This option allows to bridge the STA side. It is intended to be used in setups where the STA is doing handoff between multiple APs. There is no configuration o… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.81 | ColumncfgWlanIfaceL2natLearningMode | read-write | current | From which type of frames the IP/MAC table may be learned. When `cfgWlanIfaceL2nat` is enabled a table of the association between IP-addresses and MAC-addresse… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.82 | ColumncfgWlanIfaceL2natDefaultDestination | read-write | current | This option defines the default MAC address to send frames to. Whenever a unicast frame is received for which no learned entry exists, or which isn't a L3 fram… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.90 | ColumncfgWlanIfaceTimeAdvertisement | read-write | current | Enable AP to include local time in association response frames. This provides a mean for APs to distribute its local system time to STAs in setups where device… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.2.1.100 | ColumncfgWlanIfaceApIsolate | read-write | current | Enable AP clients isolation. If enabled, clients connected to this AP can't communicate to each other. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3 | TablecfgWlanHandoffTable | not-accessible | current | Wireless handoff parameters. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1 | RowcfgWlanHandoffTableEntry | not-accessible | current | Wireless handoff parameters entry. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.1 | ColumncfgWlanHoIndex | not-accessible | current | Entry index of table. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.2 | ColumncfgWlanHoIfaceName | read-only | current | Name of the virtual wireless interface. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.3 | ColumncfgWlanHoProfile | read-write | current | Handoff profile. * **t2gv1(1):** Train to Ground v1 * **t2gv2(2):** Train to Ground v2 * **t2gv2fg(3):** Train to Ground v2 fg scan * **t2gv3(4):** Train to Gr… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.5 | ColumncfgWlanHoScanningLevel | read-write | current | Scanning level in RSSI. When the RSSI level of the currently connected access point drops below the value configured in this parameter, the STA will scan for b… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.6 | ColumncfgWlanHoBeacons | read-write | current | Number of beacons which have to be received from an AP before a decision about handoff is allowed. Essentially forces the STA to stay on a given AP for <cfgWla… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.7 | ColumncfgWlanHoRecovery | read-write | current | Recovery time in milliseconds after a successful handoff. During this time no further handoff will be executed. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.9 | ColumncfgWlanHoFilterMode | read-write | current | RSSI filter mode. * **short(0):** high responsive static IIR RSSI filter. * **long(1):** configurable IIR RSSI filter. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.10 | ColumncfgWlanHoFilterLongX | read-write | current | IIR Filter Parameter x for long RSSI filter. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.11 | ColumncfgWlanHoFilterLongY | read-write | current | IIR Filter Parameter y for long RSSI filter. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.12 | ColumncfgWlanHoScanRateLimitTime | read-write | current | Time in milliseconds (4ms steps) in which a number of attempts to connect to an AP can be tried. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.13 | ColumncfgWlanHoScanRateLimitTries | read-write | current | Number of attempts to connect to an AP before the AP is blacklisted and ignored. The AP is removed from the blacklist after `cfgWlanHoScanRateLimitTime` since … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.16 | ColumncfgWlanHoPassiveChanTime | read-write | current | Time in milliseconds (4ms steps) we stay on a channel during passive scanning and wait for beacons. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.18 | ColumncfgWlanHoLevelLow | read-write | current | Scanning level low in RSSI. When the RSSI level to the current connected AP is below this value, perform a handoff to the next AP. This value is only active wh… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.19 | ColumncfgWlanHoLevelHigh | read-write | current | Scanning level high in RSSI. When the RSSI level to the current connected AP is above this value, perform a handoff to the next AP. This value is only active w… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.20 | ColumncfgWlanHoDistanceNear | read-write | current | Distance level near. When the measured distance to the current connected AP is below this value in meters, perform a handoff to the next AP. This value is only… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.21 | ColumncfgWlanHoDistanceFar | read-write | current | Distance level far. When the measured distance to the current connected AP is above this value in meters, perform a handoff to the next AP. This value is only … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.22 | ColumncfgWlanHoDistanceMeasurementPeriod | read-write | current | Distance ranging measurement period in milliseconds. Setting zero disables distance handoff. This value is only active when `cfgWlanHoProfile` is set to T2Gv3.… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.23 | ColumncfgWlanHoDistanceFilterX | read-write | current | IIR Filter Parameter x for distance measurement. This value is only active when `cfgWlanHoProfile` is set to T2Gv3. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.3.1.24 | ColumncfgWlanHoDistanceFilterY | read-write | current | IIR Filter Parameter y for distance measurements. This value is only active when `cfgWlanHoProfile` is set to T2Gv3. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4 | TablecfgWlanFreqTable | not-accessible | current | Frequency list entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1 | RowcfgWlanFreqTableEntry | not-accessible | current | Frequency list entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.1 | ColumncfgWlanFIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.2 | ColumncfgWlanFFreq0 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.3 | ColumncfgWlanFFreq1 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.4 | ColumncfgWlanFFreq2 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.5 | ColumncfgWlanFFreq3 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.6 | ColumncfgWlanFFreq4 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.7 | ColumncfgWlanFFreq5 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.8 | ColumncfgWlanFFreq6 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.9 | ColumncfgWlanFFreq7 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.10 | ColumncfgWlanFFreq8 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.11 | ColumncfgWlanFFreq9 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.12 | ColumncfgWlanFFreq10 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.13 | ColumncfgWlanFFreq11 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.14 | ColumncfgWlanFFreq12 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.15 | ColumncfgWlanFFreq13 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.16 | ColumncfgWlanFFreq14 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.17 | ColumncfgWlanFFreq15 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.18 | ColumncfgWlanFFreq16 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.19 | ColumncfgWlanFFreq17 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.20 | ColumncfgWlanFFreq18 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.21 | ColumncfgWlanFFreq19 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.22 | ColumncfgWlanFFreq20 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.23 | ColumncfgWlanFFreq21 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.24 | ColumncfgWlanFFreq22 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.4.1.25 | ColumncfgWlanFFreq23 | read-write | current | Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5 | TablecfgWlanWmeTable | not-accessible | current | Wireless Multimedia Extensions (WME) based on the IEEE 802.11e standard. It provides basic Quality of Service (QoS) features to IEEE 802.11 networks. The level… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1 | RowcfgWlanWmeTableEntry | not-accessible | current | WME entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.1 | ColumncfgWlanWmeIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.2 | ColumncfgWlanWmeId | read-write | current | ID of the WME parameter table. The virtual wireless interface references to this ID. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.3 | ColumncfgWlanWmeAc | read-write | current | Access category (background, besteffort, video, voice). Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.4 | ColumncfgWlanWmeCwMin | read-write | current | Contention window minimum in exponential form. Is used on STAs connected to this AP: `Real value = (2^n)-1` Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.5 | ColumncfgWlanWmeCwMax | read-write | current | Contention window maximum in exponential form. Is used on STAs connected to this AP: `Real value = (2^n)-1` Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.6 | ColumncfgWlanWmeAifs | read-write | current | Arbitration inter-frame space. Is used on STAs connected to this AP. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.7 | ColumncfgWlanWmeTxOpMax | read-write | current | A Transmit Opportunity (TXOP) is a bound time interval during which a station can send as many frames as possible (as long as the duration of the transmissions… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.8 | ColumncfgWlanWmeApCwMin | read-write | current | Contention window minimum. Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. Is used on the AP itself. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.9 | ColumncfgWlanWmeApCwMax | read-write | current | Contention window maximum. Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023 cwMax has to be greater or equal cwMin. Is used on the AP itself. Applies t… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.10 | ColumncfgWlanWmeApAifs | read-write | current | Arbitration inter-frame space. Is used on the AP itself. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.5.1.11 | ColumncfgWlanWmeApBurst | read-write | current | Maximum length for bursting (equivalent to TxOpLimit). This value is in units of 32us. Is used on the AP itself. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6 | TablecfgWlanDbgTable | not-accessible | current | Wireless Handoff Debug Parameters. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1 | RowcfgWlanDbgTableEntry | not-accessible | current | Wireless Handoff Debug Parameters Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.1 | ColumncfgWlanDbgIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.2 | ColumncfgWlanDbgIfaceName | read-only | current | Name of the virtual wireless interface. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.3 | ColumncfgWlanDbgHandoff | read-write | current | Persistent default value to enable/disable the handoff messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n prod… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.4 | ColumncfgWlanDbgScan | read-write | current | Persistent default value to enable/disable the scan messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n product… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.5 | ColumncfgWlanDbgMlme | read-write | current | Persistent default value to enable/disable the MLME messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n product… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.6 | ColumncfgWlanDbgEvents | read-write | current | Persistent default value to enable/disable the events messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n produ… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.7 | ColumncfgWlanDbgBeaconrssi | read-write | current | Persistent default value to enable/disable the beacon RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.8 | ColumncfgWlanDbgAckrssi | read-write | current | Persistent default value to enable/disable the ACK RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n pro… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.9 | ColumncfgWlanDbgBeaconfiltered | read-write | current | Persistent default value to enable/disable the beacon filtered RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA.… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.10 | ColumncfgWlanDbgRatelimit | read-write | current | Persistent default value to enable/disable the rate limiter messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.11 | ColumncfgWlanDbgLinkmonitor | read-write | current | Periodically sends a trap containing link information of all connected devices on this interface. Applies to both AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.12 | ColumncfgWlanDbgBeacontsf | read-write | current | Persistent default value to enable/disable the beacon RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! TS files is the TSF of t… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.13 | ColumncfgWlanDbgRange | read-write | current | Persistent setting for distance measurement messages in syslog. **Note:** Distance value is not in meters. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.6.1.14 | ColumncfgWlanDbgReports | read-write | current | Persistent setting for periodical WLAN debug data reporting. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7 | TablecfgWlanAclWhiteTable | not-accessible | current | Wireless MAC Access Control Whitelist |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1 | RowcfgWlanAclWhiteTableEntry | not-accessible | current | Wireless MAC Access Control Whitelist Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1.1 | ColumncfgWlanAclWhiteIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1.2 | ColumncfgWlanAclWhiteEnabled | read-write | current | Enable this entry in the ACL. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1.3 | ColumncfgWlanAclWhiteInterface | read-write | current | Name of the virtual wireless interface on which this entry is active. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1.4 | ColumncfgWlanAclWhiteAddr | read-write | current | MAC address in the ACL. **Format:** `00:14:5a:02:10:42` Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.7.1.5 | ColumncfgWlanAclWhiteMask | read-write | current | Mask of the MAC address to specify ranges of MAC addresses. To be used like CIDR notation of IP addresses. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8 | TablecfgWlanAclBlackTable | not-accessible | current | Wireless MAC Access Control Blacklist. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1 | RowcfgWlanAclBlackTableEntry | not-accessible | current | Wireless MAC Access Control Blacklist Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1.1 | ColumncfgWlanAclBlackIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1.2 | ColumncfgWlanAclBlackEnabled | read-write | current | Enable this entry in the ACL. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1.3 | ColumncfgWlanAclBlackInterface | read-write | current | Name of the virtual wireless interface on which this entry is active. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1.4 | ColumncfgWlanAclBlackAddr | read-write | current | MAC address in the ACL. **Format:** `00:14:5a:02:10:42` Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.8.1.5 | ColumncfgWlanAclBlackMask | read-write | current | Mask of the MAC address to enable the use of ranges of MAC addresses. To be used like CIDR notation of IP addresses. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.9 | NodecfgWlanGlobal | |||
| 1.3.6.1.4.1.16177.1.400.1.1.3.9.1 | ScalarcfgWlanGlblCountry | read-write | current | Wireless country code. **Note:** Refer to documentation which countries are supported for your device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.9.2 | ScalarcfgWlanGlblLinkmonitorInterval | read-write | current | LinkMonitor interval in milliseconds. A new trap is sent every <interval> milliseconds. **Note:** A short interval and/or numerous connections may affect syste… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.9.3 | ScalarcfgWlanGlblLinkmonitorQmrrlogging | read-write | current | LinkMonitor QMRR logging. If enabled, the QMRR statistics collected for phy0 are periodically printed to syslog at the interval set in `cfgWlanGlblLinkmonitorI… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.9.4 | ScalarcfgWlanGlblConnectionStatusWlanInterface | read-write | current | Persistent default of the volatile setting `swDrvConStatWlanIf` The value set here is used to initialize `swDrvConStatWlanIf`. Initialisation happens on startu… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10 | TablecfgWlan802dot1xTable | not-accessible | current | Wireless 802dot1x. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1 | RowcfgWlan802dot1xTableEntry | not-accessible | current | Wireless 802dot1x entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.1 | ColumncfgWlan802dot1xIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.2 | ColumncfgWlan802dot1xName | read-only | current | Name of the virtual wireless interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.3 | ColumncfgWlan802dot1xOwnIpAddr | read-write | current | The own IP address of the authenticator. This field is used as NAS-IP-Address RADIUS attribute. Set this to the IP address with which the authenticator will co… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.4 | ColumncfgWlan802dot1xAuthServerParameter | read-write | current | Reference ID to the radius auth server table. Uses all parameters in the cfgWlan802dot1xAuthServerTable which have as cfgWlan802dot1xAuthSrvId the value set he… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.5 | ColumncfgWlan802dot1xAcctServerParameter | read-write | current | Reference ID to the radius acct server table. Uses all parameters in the cfgWlan802dot1xAcctServerTable which have as cfgWlan802dot1xAcctSrvId the value set he… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.6 | ColumncfgWlan802dot1xRetryPrimaryInterval | read-write | current | Retry interval for trying to return to the primary RADIUS server (in seconds). RADIUS client code will automatically try to use the next server when the curren… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.7 | ColumncfgWlan802dot1xInterimAccountingInterval | read-write | current | Interim accounting update interval in seconds. If this is set (larger than 0) and acct_server is configured, hostapd will send interim accounting updates every… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.8 | ColumncfgWlan802dot1xNasId | read-write | current | Optional NAS identifier string for RADIUS messages. When used, this should be unique to the NAS within the scope of the RADIUS server. For example, a fully qua… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.9 | ColumncfgWlan802dot1xEapType | read-write | current | Specify the EAP type. Applies to STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.10 | ColumncfgWlan802dot1xIdentity | read-write | current | The identity string for EAP. Applies to STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.17 | ColumncfgWlan802dot1xClientKeyPassword | read-write | current | The password to unlock the private key. This is only required if the key is encrypted. Applies to STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.10.1.18 | ColumncfgWlan802dot1xTlsControlParams | read-write | current | Bitfield to control TLS behaviour. * **0x1** ignore certificate validity time * **0x2** ignore ca certificate Applies to STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11 | TablecfgWlan802dot1xAuthServerTable | not-accessible | current | Wireless 802dot1x AuthServer. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1 | RowcfgWlan802dot1xAuthServerTableEntry | not-accessible | current | Wireless 802dot1x AuthServer entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.1 | ColumncfgWlan802dot1xAuthSrvIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.2 | ColumncfgWlan802dot1xAuthSrvEnabled | read-write | current | Enable this entry in the auth server list. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.3 | ColumncfgWlan802dot1xAuthSrvId | read-write | current | ID of the authorisation server table. The configuration item cfgWlan802dot1xAuthServerParameter references to this ID. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.4 | ColumncfgWlan802dot1xAuthSrvIpAddr | read-write | current | IP of the RADIUS server against which will be authenticated. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.5 | ColumncfgWlan802dot1xAuthSrvPort | read-write | current | Port of the RADIUS server against which will be authenticated. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.11.1.6 | ColumncfgWlan802dot1xAuthSrvSharedSecret | read-write | current | Password to connect to the specified RADIUS server. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12 | TablecfgWlan802dot1xAcctServerTable | not-accessible | current | Wireless 802dot1x AcctServer. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1 | RowcfgWlan802dot1xAcctServerTableEntry | not-accessible | current | Wireless 802dot1x AcctServer entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.1 | ColumncfgWlan802dot1xAcctSrvIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.2 | ColumncfgWlan802dot1xAcctSrvEnabled | read-write | current | Enable this entry in the acct server list. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.3 | ColumncfgWlan802dot1xAcctSrvId | read-write | current | ID of the accounting server table. The configuration item cfgWlan802dot1xAcctServerParameter refers to this ID. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.4 | ColumncfgWlan802dot1xAcctSrvIpAddr | read-write | current | IP of the RADIUS accounting server. Set to 0.0.0.0 to disable. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.5 | ColumncfgWlan802dot1xAcctSrvPort | read-write | current | Port of the RADIUS accounting server. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.12.1.6 | ColumncfgWlan802dot1xAcctSrvSharedSecret | read-write | current | Password to connect to the specified RADIUS accounting server. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13 | TablecfgWlan802dot11rTable | not-accessible | current | Wireless 802dot11r. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1 | RowcfgWlan802dot11rTableEntry | not-accessible | current | Wireless 802dot11r Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.1 | ColumncfgWlan802dot11rIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.2 | ColumncfgWlan802dot11rName | read-only | current | Name of the virtual wireless interface. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.3 | ColumncfgWlan802dot11rEnabled | read-write | current | Enable usage of 802.11r on this device. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.4 | ColumncfgWlan802dot11rMobilityDomain | read-write | current | Mobility Domain identifier (dot11FTMobilityDomainID, MDID) MDID is used to indicate a group of APs (within an ESS, i.e., sharing the same SSID) between which a… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.5 | ColumncfgWlan802dot11rPmkR0KeyHolderIdentifier | read-only | current | PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID). Configure this in the field cfgWlan802dot1xNasId. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.6 | ColumncfgWlan802dot11rPmkR0Lifetime | read-write | current | PMK-RO lifetime in seconds (dot11FTR0KeyLifetime). When Session-Timeout attribute is provided by RADIUS server, then min(Session-Timeout, cfgWlan802dot11rPmkR0… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.7 | ColumncfgWlan802dot11rPmkR1KeyHolderIdentifier | read-write | current | PMK-R1 Key Holder identifier (dot11FTR0KeyHolderID). 6-octet identifier as a hex string. This may be the same as the local MAC address. Default magic number 00… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.9 | ColumncfgWlan802dot11rPmkR1Push | read-write | current | Whether PMK-R1 push is enabled at R0KH. * **0** do not push PMK-R1 to all configured R1KHs (default). * **1** push PMK-R1 to all configured R1KHs whenever a ne… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.10 | ColumncfgWlan802dot11rR0KHParameter | read-write | current | Reference ID to the R0KH parameter table. Uses all parameters in the cfgWlan802dot11rR0KHTable which have as cfgWlan802dot11rR0KHTblId the value set here. Appl… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.11 | ColumncfgWlan802dot11rR1KHParameter | read-write | current | Reference ID to the R1KH parameter table. Uses all parameters in the cfgWlan802dot11rR1KHTable which have as cfgWlan802dot11rR1KHTblId the value set here. Appl… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.12 | ColumncfgWlan802dot11rExpirationEnabled | read-write | current | Enable/disable PMK-R0/-R1 expiration forcing. If set to **enabled(1)**, AP forces PMK-R0s and PMK-R1s expiration once a day (see `cfgWlan802dot11rExpirationTim… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.13 | ColumncfgWlan802dot11rExpirationTime | read-write | current | Daily PMK-R0/-R1 expiration time. Define time (hour:minute) at which PMK-R0s and PMK-R1s expiration is daily forced (if `cfgWlan802dot11rExpirationEnabled` is … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.13.1.14 | ColumncfgWlan802dot11rVlan | read-write | current | The 802.1q VLAN tag of 802.11r backbone traffic. Defines the VLAN tag with which all 802.11r managment frames (ethertype 0x88b7) are transmitted on the backbon… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14 | TablecfgWlan802dot11rR0KHTable | not-accessible | current | Wireless 802dot11r R0KH. List of R0KHs in the same Mobility Domain. This list is used to map R0KH-ID (NAS Identifier) to a destination MAC address when request… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1 | RowcfgWlan802dot11rR0KHTableEntry | not-accessible | current | Wireless 802dot11r R0KH Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.1 | ColumncfgWlan802dot11rR0KHIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.2 | ColumncfgWlan802dot11rR0KHId | read-write | current | ID of the R0KH table. The configuration item cfgWlan802dot11rR0KHParameter references to this ID. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.3 | ColumncfgWlan802dot11rR0KHEnabled | read-write | current | Enable this entry in the R0KH list. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.4 | ColumncfgWlan802dot11rR0KHDestinationMac | read-write | current | MAC addresses of all possible R0KHs from which PMK-R1 can be requested. **Format:** `02:01:02:03:04:05` Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.5 | ColumncfgWlan802dot11rR0KHHID | read-write | current | NAS Identifier of all R0KHs to map to the MAC address. See the field: cfgWlan802dot11rPmkR0KeyHolderIdentifier. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.14.1.6 | ColumncfgWlan802dot11rR0KHKey | read-write | current | Static Key of the R0KH. Connecting R1KHs need to have this key configured. **Format:** `000102030405060708090a0b0c0d0e0f` Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15 | TablecfgWlan802dot11rR1KHTable | not-accessible | current | Wireless 802dot11r R1KH. List of R1KHs in the same Mobility Domain This list is used to map R1KH-ID to a destination MAC address when sending PMK-R1 key from t… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1 | RowcfgWlan802dot11rR1KHTableEntry | not-accessible | current | Wireless 802dot11r R1KH Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.1 | ColumncfgWlan802dot11rR1KHIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.2 | ColumncfgWlan802dot11rR1KHId | read-write | current | ID of the R1KH table. The configuration item cfgWlan802dot11rR1KHParameter references to this ID. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.3 | ColumncfgWlan802dot11rR1KHEnabled | read-write | current | Enable this entry in the R1KH list. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.4 | ColumncfgWlan802dot11rR1KHDestinationMac | read-write | current | MAC addresses of all R1KHs which can reqest PMK-R1 from the local R0KH. **Format:** `02:01:02:03:04:05` Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.5 | ColumncfgWlan802dot11rR1KHHID | read-write | current | PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) 6-octet identifier as a hex string to map to the MAC. This may be the same as the destination MAC. See the … |
| 1.3.6.1.4.1.16177.1.400.1.1.3.15.1.6 | ColumncfgWlan802dot11rR1KHKey | read-write | current | Static Key of the R0KH. These keys are used wenn sending updates to R1KHs from the local R0KH. The respective key has to match the respective entry on the targ… |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16 | TablecfgWlanNeighbourTable | not-accessible | current | Hostapd Neighbour Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1 | RowcfgWlanNeighbourTableEntry | not-accessible | current | Hostapd Neighbour Table Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1.1 | ColumncfgWlanNeighbourIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1.2 | ColumncfgWlanNeighbourId | read-write | current | ID of the neighbour table. The configuration item `cfgWlanIfaceNeighbourParameter` references to this ID. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1.3 | ColumncfgWlanNeighbourEnabled | read-write | current | Enable this entry in the list. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1.4 | ColumncfgWlanNeighbourBSSID | read-write | current | BSSID (MAC address) of the neighbour. **Format:** `00:14:5a:02:10:42` Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.1.3.16.1.5 | ColumncfgWlanNeighbourFrequency | read-write | current | Frequency in MHz of the neighbour. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.4 | NodecfgRouting | |||
| 1.3.6.1.4.1.16177.1.400.1.1.4.1 | NodecfgRouteDefault | |||
| 1.3.6.1.4.1.16177.1.400.1.1.4.1.1 | ScalarcfgRouteDefGateway | read-write | current | The default gateway defines the node on an IP network that serves as a router for any other network which is not defined in the routing table. Applies to AP an… |
| 1.3.6.1.4.1.16177.1.400.1.1.4.1.2 | ScalarcfgRouteDefGwOverride | read-write | current | Override a default gateway previously received via DHCP with the value in cfgRouteDefGateway. If this is disabled and a default gateway already exists it will … |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2 | TablecfgRouteTable | not-accessible | current | Static routes |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1 | RowcfgRouteTableEntry | not-accessible | current | Static route. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.1 | ColumncfgRouteTableIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.2 | ColumncfgRouteTableEnabled | read-write | current | Enable/Disable this route entry. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.3 | ColumncfgRouteTableDestinationNetwork | read-write | current | Destination network in CIDR notation. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.5 | ColumncfgRouteTableGateway | read-write | current | Gateway to destination network. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.6 | ColumncfgRouteTableSource | read-write | current | Source for traffic to destination network. Optional. Use only if you have multiple possible sources. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.2.1.8 | ColumncfgRouteTableCarpId | read-write | current | The CARP instance which brings this route up. Has to be set to -1 when this is a normal route and should not be handled by a CARP instance. All routes which ha… |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3 | TablecfgMRouteTable | not-accessible | current | Static multicast routes. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1 | RowcfgMRouteTableEntry | not-accessible | current | Static multicast routes. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.1 | ColumncfgMRouteTableIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.2 | ColumncfgMRouteTableEnabled | read-write | current | Enable/Disable this multicast route entry. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.3 | ColumncfgMRouteTableInput | read-write | current | Input interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.4 | ColumncfgMRouteTableSource | read-write | current | Unicast source address to listen to. If it is set to 0.0.0.0 all multicast traffic will be forwarded. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.5 | ColumncfgMRouteTableGroup | read-write | current | Multicast group to forward. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.4.3.1.6 | ColumncfgMRouteTableOutput | read-write | current | Output interface(s). Can be a list of interface names separated by spaces. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.5 | NodecfgIpTables | |||
| 1.3.6.1.4.1.16177.1.400.1.1.6 | NodecfgQos | |||
| 1.3.6.1.4.1.16177.1.400.1.1.6.1 | ScalarcfgQosL3PrioEnabled | read-write | current | Layer 3 Prioritization. Controls IP Precedence based priority assignments. Actual prioritization on the wireless link only occurs if `cfgQosWmeEnabled` is enab… |
| 1.3.6.1.4.1.16177.1.400.1.1.6.2 | TablecfgQosDscpToTidMapTable | not-accessible | current | Mapping table from DSCP class selector (IP TOS) to wireless priority (TID). |
| 1.3.6.1.4.1.16177.1.400.1.1.6.2.1 | RowcfgQosDscpToTidMapTableEntry | not-accessible | current | QoS DSCP to TID Mapping Table Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.2.1.1 | ColumncfgQosDscpToTidMapTableIndex | not-accessible | current | QoS DSCP to TID Mapping Table Index. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.2.1.2 | ColumncfgQosDscpToTidMapValue | read-write | current | Layer 2 priorities for IP precedence values 0-7. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.3 | TablecfgQosVlanToTidMapTable | not-accessible | current | Mapping table from layer 2 priorities (802.1p) to wireless priority (TID). |
| 1.3.6.1.4.1.16177.1.400.1.1.6.3.1 | RowcfgQosVlanToTidMapTableEntry | not-accessible | current | QoS Vlan to TID Priority Table Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.3.1.1 | ColumncfgQosVlanToTidMapTableIndex | not-accessible | current | QoS Vlan to TID Priority Table Entry Index. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.3.1.2 | ColumncfgQosVlanToTidMapValue | read-write | current | Layer 2 priorities for VLAN priorities 0-7. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4 | TablecfgQosIpToTidMapTable | not-accessible | current | Mapping table from IP header (Source, Destination, Protocol, Port), to wireless priority (TID). |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1 | RowcfgQosIpToTidMapTableEntry | not-accessible | current | IP to TID Priority Table Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.1 | ColumncfgQosIpToTidMapTableIndex | not-accessible | current | IP to TID Priority Table Index. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.2 | ColumncfgQosIpToTidMapSrcNet | read-write | current | Source network for ip prioritization rule, in CIDR format. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.3 | ColumncfgQosIpToTidMapDestNet | read-write | current | Destination network for ip prioritization rule, in CIDR format. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.4 | ColumncfgQosIpToTidMapProto | read-write | current | Protocol for ip prioritization rule, allowed protocols are: **any(0)**, **udp(1)** or **tcp(2)**. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.5 | ColumncfgQosIpToTidMapSrcPort | read-write | current | Source port for ip prioritization rule, use port -1 to match any port. This setting can only be used if the protocol is set to udp or tcp. Applies to AP and ST… |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.6 | ColumncfgQosIpToTidMapDestPort | read-write | current | Destination port for ip prioritization rule, use port -1 to match any port. This setting can only be used if the protocol is set to udp or tcp. Applies to AP a… |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.7 | ColumncfgQosIpToTidMapPrecedence | read-write | current | Precedence to set for ip prioritization rule. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.6.4.1.8 | ColumncfgQosIpToTidMapEnabled | read-write | current | Enable/disable ip prioritisation rules. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.11 | NodecfgLogging | |||
| 1.3.6.1.4.1.16177.1.400.1.1.11.2 | NodecfgLogRemote | |||
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1 | TablecfgLogRemoteTable | not-accessible | current | List of syslog destinations. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1 | RowcfgLogRemoteTableEntry | not-accessible | current | List of syslog destinations. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.1 | ColumncfgLogRemoteIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.2 | ColumncfgLogRemoteEnabled | read-write | current | Log messages to file. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.3 | ColumncfgLogRemoteLevel | read-only | current | Log only messages with equal or higher priority than prio N (0-7). Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.4 | ColumncfgLogRemoteProtocol | read-write | current | Protocol to send log messages. The udp(0) protocol complies with the standard syslog protocol. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.5 | ColumncfgLogRemoteIp | read-write | current | Remote IP address. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.6 | ColumncfgLogRemotePort | read-write | current | Remote port. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12 | NodecfgSnmp | |||
| 1.3.6.1.4.1.16177.1.400.1.1.12.1 | NodecfgSnmpd | |||
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.1 | ScalarcfgSnmpdLocation | read-write | current | SNMP system location. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.2 | ScalarcfgSnmpdContact | read-write | current | SNMP contact. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.3 | ScalarcfgSnmpdVersion | read-write | current | SNMP version, either **v2c(0)** or **v3usm(1)**, for the users admin, maintainer and monitor. Please refer to the user guide for more information about the acc… |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.4 | ScalarcfgSnmpdName | read-write | current | SNMP node name often used in NMS. By convention, this is the node's fully-qualified domain name. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.5 | ScalarcfgSnmpdEnabled | read-write | current | Enable or disable the SNMP Agent. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.6 | ScalarcfgSnmpdAddress | read-write | current | Address to which the SNMP Agent binds. The default is 'udp:0.0.0.0:161'. When defining a configuration, default arguments may be ommited. Multiple space and/or… |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.100 | NodecfgSnmpdCommunity | |||
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.100.1 | ScalarcfgSnmpdComAdmin | read-write | current | Password for the administrator. This is the community or the passphrase for the user administrator depending on the cfgSnmpdVersion: * **v2c:** community strin… |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.100.2 | ScalarcfgSnmpdComMaintainer | read-write | current | Password for the maintainer. This is the community or the passphrase for the user maintainer depending on the cfgSnmpdVersion: * **v2c:** community string for … |
| 1.3.6.1.4.1.16177.1.400.1.1.12.1.100.3 | ScalarcfgSnmpdComMonitor | read-write | current | Password for the monitor. This is the community or the passphrase for the user monitor depending on the cfgSnmpdVersion: * **v2c:** community string for monito… |
| 1.3.6.1.4.1.16177.1.400.1.1.12.10 | NodecfgSnmpTrap | |||
| 1.3.6.1.4.1.16177.1.400.1.1.12.10.1 | ScalarcfgSnmpTrapEnabled | read-write | current | Enable sending of SNMP traps. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.10.2 | ScalarcfgSnmpTrapVersion | read-write | current | SNMP version with which traps are sent. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.10.3 | ScalarcfgSnmpTrapCommunity | read-write | current | SNMP community if SNMP v2c is used. If SNMP v3 is used the community string is the password. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.12.10.4 | ScalarcfgSnmpTrapDest | read-write | current | IP address of the trap receiver. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13 | NodecfgDhcp | |||
| 1.3.6.1.4.1.16177.1.400.1.1.13.1 | NodecfgDhcpGlobal | |||
| 1.3.6.1.4.1.16177.1.400.1.1.13.1.1 | ScalarcfgDhcpGlobalEnabled | read-write | current | Enable DHCP server functionality. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.2 | TablecfgDhcpDnsmasqTable | not-accessible | current | DHCP Dnsmasq instances. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.2.1 | RowcfgDhcpDnsmasqTableEntry | not-accessible | current | DHCP Dnsmasq instances. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.2.1.1 | ColumncfgDhcpDnsmasqIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.2.1.2 | ColumncfgDhcpDnsmasqScopeParameter | read-write | current | Parameter to set which scope ID to use for the DHCP server. This is used in conjunction with the scope ID parameter (see cfgDhcpScopeId). |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3 | TablecfgDhcpScopeTable | not-accessible | current | DHCP instance configs. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1 | RowcfgDhcpScopeTableEntry | not-accessible | current | DHCP instance configs. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.1 | ColumncfgDhcpScopeIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.2 | ColumncfgDhcpScopeId | read-write | current | Several scopes can share the same ID. This is used in conjunction with the DHCP parameter (see cfgDhcpDnsmasqScopeParameter). Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.3 | ColumncfgDhcpScopeInterface | read-write | current | Network interface (ETH, VLAN, WLAN) on which the DHCP server runs. If the interface is part of a bridge, the server will run on that bridge. Applies to AP and … |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.4 | ColumncfgDhcpScopeStart | read-write | current | Specifies the offset from the network address of the underlying interface to calculate the minimum address that may be leased to clients. It may be greater tha… |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.5 | ColumncfgDhcpScopeLimit | read-write | current | Specifies the maximum allowable address that may be leased to clients, calculated as network address + 'start' + 'limit'. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.6 | ColumncfgDhcpScopeLeasetime | read-write | current | Specifies the lease time of addresses handed out to clients, e.g. 12h or 30m. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.7 | ColumncfgDhcpScopeGateway | read-write | current | Specifies the gateway address handed out to clients. A value of 0.0.0.0 means not used. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.8 | ColumncfgDhcpScopeDnsServer1 | read-write | current | Specifies the primary DNS server address handed out to clients. A value of 0.0.0.0 means not used. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.13.3.1.9 | ColumncfgDhcpScopeDnsServer2 | read-write | current | Specifies the secondary DNS server address handed out to clients. If the first DNS server is not used, this server will also be ignored. A value of 0.0.0.0 mea… |
| 1.3.6.1.4.1.16177.1.400.1.1.14 | NodecfgNtp | |||
| 1.3.6.1.4.1.16177.1.400.1.1.14.1 | ScalarcfgNtpEnabled | read-write | current | Synchronize the system time with given server. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.14.2 | ScalarcfgNtpServer1 | read-write | current | NTP server 1. If the IP is set to 0.0.0.0 the NTP client will only listen to broadcast packages. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.14.3 | ScalarcfgNtpServer2 | read-write | current | NTP server 2. Used as fallback if server 1 cannot be reached. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.15 | NodecfgHttp | |||
| 1.3.6.1.4.1.16177.1.400.1.1.15.1 | ScalarcfgHttpUser | read-only | current | Web administrator username. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.15.2 | ScalarcfgHttpPassword | read-write | current | Web administrator password. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.15.3 | ScalarcfgHttpEnabled | read-write | current | Configure if the webserver shall be started. When disabling the webserver, make sure you still have another way to access the device, e.g by CLI or via SNMP. A… |
| 1.3.6.1.4.1.16177.1.400.1.1.15.4 | ScalarcfgHttpRedirectEnabled | read-write | current | If enabled, all access to `cfgHttpHttpAddress` shall be redirected to `cfgHttpHttpsAddress`. This does not disable http. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.15.5 | ScalarcfgHttpHttpAddress | read-write | current | Address to which the http server binds. The default is '0.0.0.0:80'. Multiple space and/or comma separated tuples are allowed. **Examples** * 192.168.1.20:80 *… |
| 1.3.6.1.4.1.16177.1.400.1.1.15.6 | ScalarcfgHttpHttpsAddress | read-write | current | Address to which the https server binds. The default is '0.0.0.0:443'. Multiple space and/or comma separated tuples are allowed. **Examples** * 192.168.1.20:44… |
| 1.3.6.1.4.1.16177.1.400.1.1.16 | NodecfgLldp | |||
| 1.3.6.1.4.1.16177.1.400.1.1.16.1 | ScalarcfgLldpEnabled | read-write | current | Enable LLDP. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.16.2 | ScalarcfgLldpDescription | read-write | current | LLDP Description Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.17 | NodecfgMdns | |||
| 1.3.6.1.4.1.16177.1.400.1.1.17.1 | ScalarcfgMdnsEnabled | read-write | current | Enable mDNS. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.17.2 | ScalarcfgMdnsNetwork | read-write | current | Space separated list of mDNS aware network interfaces |
| 1.3.6.1.4.1.16177.1.400.1.1.40 | NodecfgNlm | |||
| 1.3.6.1.4.1.16177.1.400.1.1.40.1 | NodecfgNlmGlobal | |||
| 1.3.6.1.4.1.16177.1.400.1.1.40.1.1 | ScalarcfgNlmGlblEnabled | read-write | current | Enable the Network Link Monitor. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2 | TablecfgNlmMonitorTable | not-accessible | current | NLM Monitor Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1 | RowcfgNlmMonitorTableEntry | not-accessible | current | NLM Monitor Table Entry. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.1 | ColumncfgNlmMonIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.2 | ColumncfgNlmMonEnabled | read-write | current | Enable this entry in the monitor list. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.3 | ColumncfgNlmMonInterval | read-write | current | Execution interval of this monitor in milliseconds. In case of an event driven monitor (e.g. `cfgNlmMonType` set to **wlan(2)**), this defines a timeout. Appli… |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.4 | ColumncfgNlmMonCount | read-write | current | NLM monitor counter. The number of times the measured criteria has to be down, until the monitor is reported as down. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.5 | ColumncfgNlmMonType | read-write | current | Objects which can be monitored. * **phy(0)** monitor checks periodically the link status of the ethernet interfaces defined by `cfgNlmMonInterfaces`. If at lea… |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.6 | ColumncfgNlmMonInterfaces | read-write | current | NLM monitor interface(s). This parameter specifies the name of the interface(s) which is/are to be monitored. For the type **phy(0)** multiple interfaces are a… |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.7 | ColumncfgNlmMonDestination | read-write | current | NLM monitor destination. This parameter specifies the IPv4 address which is to be monitored. It will only be used when `cfgNlmMonType` is set to **icmp(1)**. A… |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.10 | ColumncfgNlmMonUpAction | read-write | current | NLM 'up' state monitor action. The action is executed on a monitor-state transition to 'up'. Set to 0 to disable (i.e. no action). Supported actions: **1xxx** … |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.11 | ColumncfgNlmMonDownAction | read-write | current | NLM 'down' state monitor script. The action is executed on a monitor-state transition to 'down'. Set to 0 to disable (i.e. no action). Supported actions: **1xx… |
| 1.3.6.1.4.1.16177.1.400.1.1.40.2.1.12 | ColumncfgNlmMonScanLoopInterval | read-write | current | Scan loop debounce interval in milliseconds. If set to non-zero it will mark interface 'down' after receiving scan loop trap 415 and mark it 'up' after scan lo… |
| 1.3.6.1.4.1.16177.1.400.1.1.100 | NodecfgCli | |||
| 1.3.6.1.4.1.16177.1.400.1.1.100.1 | ScalarcfgCliEnabled | read-write | current | CLI feature support configuration. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.100.2 | ScalarcfgCliUsername | read-write | current | CLI username. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.100.3 | ScalarcfgCliPassword | read-write | current | CLI password. For SSH, a password is mandatory. Accessing the device via telnet without using a password is done by setting the password to an empty string (ze… |
| 1.3.6.1.4.1.16177.1.400.1.1.100.4 | ScalarcfgCliTelnetEnabled | read-write | current | CLI telnet support configuration. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.100.6 | ScalarcfgCliSshEnabled | read-write | current | CLI ssh support configuration. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.1.100.8 | ScalarcfgCliTelnetAddress | read-write | current | Address to which the telnet server for CLI binds. The default is '0.0.0.0:23'. Multiple space and/or comma separated tuples are allowed. **Examples** * 192.168… |
| 1.3.6.1.4.1.16177.1.400.1.1.100.9 | ScalarcfgCliSshAddress | read-write | current | Address to which the ssh server for CLI binds. The default is '0.0.0.0:22'. Multiple space and/or comma separated tuples are allowed. **Examples** * 192.168.1.… |
| 1.3.6.1.4.1.16177.1.400.1.1.101 | NodecfgCellular | |||
| 1.3.6.1.4.1.16177.1.400.1.1.101.1 | TablecfgCellSimTable | not-accessible | current | SIM parameter table Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1 | RowcfgCellSimTableEntry | not-accessible | current | SIM parameter table entry Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.1 | ColumncfgCellSimIndex | not-accessible | current | SIM parameter table entry index Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.2 | ColumncfgCellSimApn | read-write | current | APN (Access Point Name) **Example** * gprs.swisscom.ch Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.3 | ColumncfgCellSimUsername | read-write | current | Username Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.4 | ColumncfgCellSimPassword | read-write | current | Password Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.5 | ColumncfgCellSimPinEnabled | read-write | current | PIN authentication enabled Set to enabled if PIN authentication is required for this SIM. Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.6 | ColumncfgCellSimPin | read-write | current | SIM PIN Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.1.101.1.1.7 | ColumncfgCellSimAuthType | read-write | current | Authentication type Applies to LTE products only. |
| 1.3.6.1.4.1.16177.1.400.1.3 | Noderpc | |||
| 1.3.6.1.4.1.16177.1.400.1.3.1 | NoderpcConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.1.3.1.1 | ScalarrpcCfgRevert | read-write | current | In case there are any changes in the configuration section, which are not applied yet, they can be all reverted by writing **all(1)** to this parameter. Readin… |
| 1.3.6.1.4.1.16177.1.400.1.3.1.2 | ScalarrpcCfgApply | read-write | current | All changes to any parameter in the configuration section have to be applied before they come into operation. To apply all new parameters to the device, set th… |
| 1.3.6.1.4.1.16177.1.400.1.3.1.4 | ScalarrpcCfgFile | read-write | current | Export or import a configuration to or from a file respectively. Please refer to setCfgFileUrl for more information on how to set the configuration file. Readi… |
| 1.3.6.1.4.1.16177.1.400.1.3.2 | NoderpcFirmware | |||
| 1.3.6.1.4.1.16177.1.400.1.3.2.1 | ScalarrpcFwFlash | read-write | current | Start download/flash of a new firmware. To flash a new firmware to the device, define a valid URL accessible by the device. Change the firmware URL parameter `… |
| 1.3.6.1.4.1.16177.1.400.1.3.3 | NoderpcSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.3.3.1 | ScalarrpcSysReboot | read-write | current | Reboot system after n seconds. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.3.3.2 | ScalarrpcSysFactoryReset | read-write | current | Perform a factory reset (i.e. reset device configuration, including administrator password and HTTPS/802.1x certificates, to its default state). **Note:** You … |
| 1.3.6.1.4.1.16177.1.400.1.3.3.3 | ScalarrpcSysErrorReset | read-write | current | Writing **reset(1)** to this parameter will reset all logged warning and errors of the system. The device LEDs will indicate normal operating state after resul… |
| 1.3.6.1.4.1.16177.1.400.1.3.3.4 | ScalarrpcSysKernelLogReset | read-write | current | Reset kernel logs. * Writing **reset(1)** to this parameter will clear all kernel logs. * Reading this parameter will show the status of the process. A **nop(0… |
| 1.3.6.1.4.1.16177.1.400.1.3.4 | NoderpcCertificate | |||
| 1.3.6.1.4.1.16177.1.400.1.3.4.1 | ScalarrpcCrtFile | read-write | current | Import or export a HTTPS/802.1X certification/key to or from a file respectively. Please refer to setCrtFileUrl for more information on how to set the certific… |
| 1.3.6.1.4.1.16177.1.400.1.3.6 | NoderpcDriver | |||
| 1.3.6.1.4.1.16177.1.400.1.3.6.1 | TablerpcDrvTable | not-accessible | current | RPC driver module |
| 1.3.6.1.4.1.16177.1.400.1.3.6.1.1 | RowrpcDrvTableEntry | not-accessible | current | RPC driver module |
| 1.3.6.1.4.1.16177.1.400.1.3.6.1.1.1 | ColumnrpcDrvIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.3.6.1.1.2 | ColumnrpcDrvName | read-only | current | Name of the radio device Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.3.6.1.1.5 | ColumnrpcDrvDfsSimulateRadar | read-write | current | Simulate a radar detection on the current channel. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.4 | Nodesettings | |||
| 1.3.6.1.4.1.16177.1.400.1.4.1 | NodesetConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.1.4.1.1 | ScalarsetCfgFileUrl | read-write | current | The configuration file URL defines to or from which location the configuration file will be exported or imported. At the moment only TFTP protocol is supported… |
| 1.3.6.1.4.1.16177.1.400.1.4.3 | NodesetWireless | |||
| 1.3.6.1.4.1.16177.1.400.1.4.3.1 | TablesetWlanDeviceTable | not-accessible | current | Wireless hardware modules. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1 | RowsetWlanDeviceTableEntry | not-accessible | current | Wireless hardware module. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1.1 | ColumnsetWlanDevIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1.2 | ColumnsetWlanDevName | read-only | current | Name of the wireless device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1.3 | ColumnsetWlanDevRfOutput | read-write | current | Enable/disable RF output. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1.6 | ColumnsetWlanDevFrequency | read-write | current | Wireless frequency in MHz. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.1.1.8 | ColumnsetWlanDevPower | read-write | current | Wireless output power as effective isotropic radiated power (EIRP) in dBm including antenna gain. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6 | TablesetWlanDbgTable | not-accessible | current | Wireless handoff debug parameters. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1 | RowsetWlanDbgTableEntry | not-accessible | current | Wireless handoff debug parameters entry. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.1 | ColumnsetWlanDbgIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.2 | ColumnsetWlanDbgIfaceName | read-only | current | Name of the virtual wireless interface. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.3 | ColumnsetWlanDbgHandoff | read-write | current | Volatile setting to enable/disable the handoff messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.4 | ColumnsetWlanDbgScan | read-write | current | Volatile setting to enable/disable the scan messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.5 | ColumnsetWlanDbgMlme | read-write | current | Volatile setting to enable/disable the MLME messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.6 | ColumnsetWlanDbgEvents | read-write | current | Volatile setting to enable/disable the Events messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.7 | ColumnsetWlanDbgBeaconrssi | read-write | current | Volatile setting to enable/disable the Beacon RSSI messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.8 | ColumnsetWlanDbgAckrssi | read-write | current | Volatile setting to enable/disable the ACK RSSI messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.9 | ColumnsetWlanDbgBeaconfiltered | read-write | current | Volatile setting to enable/disable the Beacon filtered RSSI messages in syslog. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.10 | ColumnsetWlanDbgRatelimit | read-write | current | Volatile value to enable/disable the rate limiter messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products … |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.12 | ColumnsetWlanDbgBeacontsf | read-write | current | Volatile setting to enable/disable the beacon RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! TS is internal TSF. Applies to S… |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.13 | ColumnsetWlanDbgRange | read-write | current | Volatile setting for distance measurement messages in syslog. **Note:** Distance value is not in meters. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.3.6.1.14 | ColumnsetWlanDbgReports | read-write | current | Volatile setting for periodical WLAN debug data reporting. Applies to STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.4.4 | NodesetConfmgmtd | |||
| 1.3.6.1.4.1.16177.1.400.1.4.4.1 | ScalarsetCfgdLogLevel | read-write | current | Log message level, N = 0-8. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.4.5 | NodesetFirmware | |||
| 1.3.6.1.4.1.16177.1.400.1.4.5.1 | ScalarsetFwFileUrl | read-write | current | Download firmware from this URL. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.4.5.2 | ScalarsetFwKeepConfig | read-write | current | Try to import configuration from the previous firmware version. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.4.6 | NodesetCertificate | |||
| 1.3.6.1.4.1.16177.1.400.1.4.6.1 | ScalarsetCrtFileUrl | read-write | current | Download/upload URL for HTTPS/802.1x certificats and keys The certification/key (for HTTPS/802.1X) file-URL defines the location of the certification/key file … |
| 1.3.6.1.4.1.16177.1.400.1.4.6.2 | ScalarsetCrtFileSelector | read-write | current | Set this field to select which file should be downloaded/uploaded via the rpcCrtFile. * **0** means legacy HTTPS. Upload/download certificate and key from the … |
| 1.3.6.1.4.1.16177.1.400.1.4.6.3 | ScalarsetCrtFileFormat | read-write | current | Set the certificate/key file format for `rpcCrtFile` actions * **0** means the imported/exported certificate/key will be in the PEM format. * **1** means the i… |
| 1.3.6.1.4.1.16177.1.400.1.4.6.4 | ScalarsetCrtFilePkcs12Passphrase | read-write | current | Set the PKCS#12 passphrase used to import with `rpcCertFile` This passphrase will be used during the import to decrypt the container data. The `cfgWlan802dot1x… |
| 1.3.6.1.4.1.16177.1.400.1.4.7 | NodesetSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.4.7.1 | ScalarsetSysTime | read-write | current | System time as epoch. |
| 1.3.6.1.4.1.16177.1.400.1.5 | Nodehardware | |||
| 1.3.6.1.4.1.16177.1.400.1.5.1 | NodehwSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.5.1.1 | ScalarhwSysProduct | read-only | current | Product type. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.1.2 | ScalarhwSysSerial | read-only | current | Serial number of the product. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.1.3 | ScalarhwSysRevision | read-only | current | ERP revision of the product. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.1.4 | ScalarhwSysVersion | read-only | current | Version of the product. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2 | NodehwNetwork | |||
| 1.3.6.1.4.1.16177.1.400.1.5.2.1 | TablehwNetEthernetTable | not-accessible | current | Ethernet network interfaces |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1 | RowhwNetEthernetTableEntry | not-accessible | current | Ethernet network interface |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.1 | ColumnhwNetEthIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.2 | ColumnhwNetEthName | read-only | current | Name of the ethernet interface. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.3 | ColumnhwNetEthAssembled | read-only | current | Ethernet interface present or not. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.4 | ColumnhwNetEthMacAddress | read-only | current | Ethernet MAC address.. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.5 | ColumnhwNetEthOperation | read-only | current | Ethernet interface plugged or unplugged. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.6 | ColumnhwNetEthSpeed | read-only | current | Ethernet speed in Mbps. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.2.1.1.7 | ColumnhwNetEthHwIndex | read-only | current | The physical address of the Ethernet interface of the base board, since not all products are assembled the same way this is to describe how the wiring is done.… |
| 1.3.6.1.4.1.16177.1.400.1.5.3 | NodehwWireless | |||
| 1.3.6.1.4.1.16177.1.400.1.5.3.1 | TablehwWlanDeviceTable | not-accessible | current | Hardware information of the wireless LAN devices. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1 | RowhwWlanDeviceTableEntry | not-accessible | current | Wireless LAN devices |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.1 | ColumnhwWlanDevIndex | not-accessible | current | Entry index of table |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.2 | ColumnhwWlanDevAssembled | read-only | current | Wireless device present or not. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.3 | ColumnhwWlanDevType | read-only | current | Type of the wireless device. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.4 | ColumnhwWlanDevSerial | read-only | current | Serial number / customer field. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.5 | ColumnhwWlanDevRevision | read-only | current | ERP revision of the RF board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.6 | ColumnhwWlanDevVersion | read-only | current | Version of the RF board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.7 | ColumnhwWlanDevPcbId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.8 | ColumnhwWlanDevAssemblyId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.9 | ColumnhwWlanDevMacAddress | read-only | current | MAC address. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.10 | ColumnhwWlanDevAntennaProfileId | read-only | current | Antenna profile ID. Please check the user manual for antenna details. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.11 | ColumnhwWlanDevAntennaGain | read-only | current | Antenna gain in dBi. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.1.1.12 | ColumnhwWlanDevCableLoss | read-only | current | Cable loss in dB. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.3.2 | NodehwWlanGlobal | |||
| 1.3.6.1.4.1.16177.1.400.1.5.3.2.2 | ScalarhwWlanGlblRegulatoryRegionId | read-only | current | Regulatory region ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10 | NodehwBaseBoard | |||
| 1.3.6.1.4.1.16177.1.400.1.5.10.1 | ScalarhwBbType | read-only | current | Product type of the base board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10.2 | ScalarhwBbSerial | read-only | current | Serial number of the base board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10.3 | ScalarhwBbRevision | read-only | current | ERP revision of the base board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10.4 | ScalarhwBbVersion | read-only | current | Version of the base board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10.5 | ScalarhwBbPcbId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.10.6 | ScalarhwBbAssemblyId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11 | NodehwIfaceBoard | |||
| 1.3.6.1.4.1.16177.1.400.1.5.11.1 | ScalarhwIfBrdAssembled | read-only | current | Interface board present or not. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.2 | ScalarhwIfBrdType | read-only | current | Product type of the interface board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.3 | ScalarhwIfBrdSerial | read-only | current | Serial number of the interface board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.4 | ScalarhwIfBrdRevision | read-only | current | ERP Revision of the interface board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.5 | ScalarhwIfBrdVersion | read-only | current | Version of the interface board. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.6 | ScalarhwIfBrdPcbId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.11.7 | ScalarhwIfBrdAssemblyId | read-only | current | Hardware assembly ID. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.21 | NodehwSensor | |||
| 1.3.6.1.4.1.16177.1.400.1.5.21.1 | TablehwSensorTable | not-accessible | current | Hardware sensor information table. |
| 1.3.6.1.4.1.16177.1.400.1.5.21.1.1 | RowhwSensorTableEntry | not-accessible | current | Hardware sensor entry. |
| 1.3.6.1.4.1.16177.1.400.1.5.21.1.1.1 | ColumnhwSensorIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.5.21.1.1.2 | ColumnhwSensorName | read-only | current | Name of the hardware sensor. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.21.1.1.3 | ColumnhwSensorUnit | read-only | current | Unit of the hardware sensor. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.5.21.1.1.4 | ColumnhwSensorValue | read-only | current | Value of the hardware sensor. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6 | Nodesoftware | |||
| 1.3.6.1.4.1.16177.1.400.1.6.2 | NodeswFirmware | |||
| 1.3.6.1.4.1.16177.1.400.1.6.2.1 | ScalarswFwName | read-only | current | Firmware name. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.2.2 | ScalarswFwVersion | read-only | current | Firmware name. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.2.3 | ScalarswFwRevision | read-only | current | Firmware name. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.3 | NodeswSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.6.3.1 | ScalarswSysRebootReason | read-only | current | Reason for the reboot of the system. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.3.2 | ScalarswSysBootStatus | read-only | current | The boot status indicates whether the booting sequence of the device has been completed. |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100 | TableswSysMessageTable | not-accessible | current | System messages (e.g. errors, warnings). |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100.1 | RowswSysMessageTableEntry | not-accessible | current | System message entry |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100.1.1 | ColumnswSysMsgIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100.1.2 | ColumnswSysMsgPriority | read-only | current | Message priority/level. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100.1.3 | ColumnswSysMsgCode | read-only | current | Message code. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.3.100.1.4 | ColumnswSysMsgText | read-only | current | Message. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.4 | NodeswOperatingSystem | |||
| 1.3.6.1.4.1.16177.1.400.1.6.4.1 | ScalarswOsName | read-only | current | Operating system name. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.4.2 | ScalarswOsVersion | read-only | current | Operating system version. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.4.3 | ScalarswOsRevision | read-only | current | Operating system revision. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.4.4 | ScalarswOsUptime | read-only | current | Up time of the operating system. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.5 | NodeswDriver | |||
| 1.3.6.1.4.1.16177.1.400.1.6.5.1 | TableswDrvDfsTable | not-accessible | current | DFS driver statistics |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1 | RowswDrvDfsTableEntry | not-accessible | current | DFS driver statistics |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1.1 | ColumnswDrvDfsIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1.2 | ColumnswDrvDfsName | read-only | current | Name of the wireless device. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1.3 | ColumnswDrvDfsPulsesDetected | read-write | current | Pulses detected by the wireless device. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1.4 | ColumnswDrvDfsPulsesProcessed | read-write | current | Pulses processed by the wireless device. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.1.1.5 | ColumnswDrvDfsRadarDetected | read-write | current | Radar sequences detected by the wireless device. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4 | TableswDrvCntWlanMacTable | not-accessible | current | Wireless MAC layer statistics. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1 | RowswDrvCntWlanMacTableEntry | not-accessible | current | Wireless MAC layer statistics. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.1 | ColumnswDrvCntWlanMacIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.2 | ColumnswDrvCntWlanMacName | read-only | current | Name of the wireless device. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.3 | ColumnswDrvCntWlanMacTxHandlersDrop | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.4 | ColumnswDrvCntWlanMacTxHandlersQueued | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.5 | ColumnswDrvCntWlanMacTxHandlersDropUnencrypted | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.6 | ColumnswDrvCntWlanMacTxHandlersDropFragment | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.7 | ColumnswDrvCntWlanMacTxHandlersDropWep | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.8 | ColumnswDrvCntWlanMacTxHandlersDropNotAssoc | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.9 | ColumnswDrvCntWlanMacTxHandlersDropUnauthPort | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.10 | ColumnswDrvCntWlanMacRxHandlersDrop | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.11 | ColumnswDrvCntWlanMacRxHandlersQueued | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.12 | ColumnswDrvCntWlanMacRxHandlersDropNullfunc | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.13 | ColumnswDrvCntWlanMacRxHandlersDropDefrag | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.14 | ColumnswDrvCntWlanMacRxHandlersDropShort | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.15 | ColumnswDrvCntWlanMacTxExpandSkbHead | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.16 | ColumnswDrvCntWlanMacTxExpandSkbHeadCloned | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.17 | ColumnswDrvCntWlanMacRxExpandSkbHead | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.18 | ColumnswDrvCntWlanMacRxExpandSkbHead2 | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.19 | ColumnswDrvCntWlanMacRxHandlersFragments | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.4.1.20 | ColumnswDrvCntWlanMacTxstatusDrop | read-only | current | MAC debug entry. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6 | TableswDrvCntWlanWmmTable | not-accessible | current | WMM statistics. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1 | RowswDrvCntWlanWmmTableEntry | not-accessible | current | WMM statistics. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.1 | ColumnswDrvCntWlanWmmTableIndex | not-accessible | current | Entry index of table. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.2 | ColumnswDrvCntWlanWmmName | read-only | current | Name of the queue. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.3 | ColumnswDrvCntWlanWmmTx | read-only | current | Number of frames sent in this queue. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.4 | ColumnswDrvCntWlanWmmRx | read-only | current | Number of frames received in this queue. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.5 | ColumnswDrvCntWlanWmmShortRetries | read-only | current | Number of retries for frames shorter than RTS. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.6 | ColumnswDrvCntWlanWmmLongRetries | read-only | current | Number of retries for frames longer than RTS. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.6.1.7 | ColumnswDrvCntWlanWmmExceededRetries | read-only | current | Number of failed transmissions due to exceeding of the retry limit. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.7 | ScalarswDrvConStatWlanIf | read-write | current | Volatile wlan interface selector for `swDrvConStatTable`. Changes made here will be lost upon reconfiguration or a reboot. Use `cfgWlanGlblConnectionStatusWlan… |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8 | TableswDrvConStatTable | not-accessible | current | Connection Status Information. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1 | RowswDrvConStatTableEntry | not-accessible | current | Connection Status Information per Station. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.1 | ColumnswDrvConStatIndex | not-accessible | current | Entry index of Table. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.2 | ColumnswDrvConStatWlanName | read-only | current | WLAN interface name. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.3 | ColumnswDrvConStatMacName | read-only | current | Station MAC address. In AP mode this is the MAC address of the connected client (STA). In client (STA) mode this is the MAC address of the AP to which the clie… |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.4 | ColumnswDrvConStatRxBrExtra | read-only | current | Station rx bitrate extra. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.5 | ColumnswDrvConStatRxBrType | read-only | current | Station rx bitrate type. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.6 | ColumnswDrvConStatRxBrValue | read-only | current | Station rx bitrate value. Multiplied by 10 if `swDrvConStatRxBrType` is 'legacy'. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.7 | ColumnswDrvConStatRxBytes | read-only | current | Station rx bytes. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.8 | ColumnswDrvConStatRxPackets | read-only | current | Station rx packets. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.9 | ColumnswDrvConStatTxBrExtra | read-only | current | Station tx bitrate extra. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.10 | ColumnswDrvConStatTxBrType | read-only | current | Station tx bitrate type. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.11 | ColumnswDrvConStatTxBrValue | read-only | current | Station tx bitrate value. Multiplied by 10 if `swDrvConStatTxBrType` is 'legacy'. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.12 | ColumnswDrvConStatTxBytes | read-only | current | Station tx bytes. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.13 | ColumnswDrvConStatTxPackets | read-only | current | Station tx packets. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.14 | ColumnswDrvConStatSigChain0 | read-only | current | Station signal chain 0 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.15 | ColumnswDrvConStatSigChain1 | read-only | current | Station signal chain 1 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.16 | ColumnswDrvConStatSigChain2 | read-only | current | Station signal chain 2 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.17 | ColumnswDrvConStatSigAvgChain0 | read-only | current | Station signal average chain 0 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.18 | ColumnswDrvConStatSigAvgChain1 | read-only | current | Station signal average chain 1 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.19 | ColumnswDrvConStatSigAvgChain2 | read-only | current | Station signal average chain 2 in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.20 | ColumnswDrvConStatTxRetries | read-only | current | Station tx retries. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.21 | ColumnswDrvConStatTxFailed | read-only | current | Station tx failed. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.22 | ColumnswDrvConStatCacheNo | read-only | current | Station Dump Cache Access Number. The cache gets refreshed if it is older than 5 seconds. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.23 | ColumnswDrvConStatSigCombined | read-only | current | Station signal combined of all active chains in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.8.1.24 | ColumnswDrvConStatSigAvgCombined | read-only | current | Station signal average combined of all active chains in dBm. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9 | TableswDrvCntWlanTable | not-accessible | current | Wireless Dev Counters |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1 | RowswDrvCntWlanTableEntry | not-accessible | current | Wireless Dev Counters |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.1 | ColumnswDrvCntWlanIndex | not-accessible | current | Entry index of Table |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.2 | ColumnswDrvCntWlanName | read-only | current | Name of the wireless Dev |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.4 | ColumnswDrvCntWlanAssocSuccess | read-only | current | Number of successful associations. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.5 | ColumnswDrvCntWlanAssocFailure | read-only | current | Number of unsuccessful associations. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.6 | ColumnswDrvCntWlanAssocFailureMaxSta | read-only | current | Number of times the maximum number of stations has been exceeded. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.7 | ColumnswDrvCntWlanNumAssocSta | read-only | current | Number of associated STA. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.8 | ColumnswDrvCntWlanEapAuthStarted | read-only | current | Number of EAP authentication sessions started since the AP has been started. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.9 | ColumnswDrvCntWlanEapAuthFailed | read-only | current | Number of EAP authentication sessions that have failed since the AP has been started. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.10 | ColumnswDrvCntWlanChannelActive | read-only | current | Time in ms during which the device has been on the current channel. On STA when it's no associated the current channel is the lowest channel of selected countr… |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.11 | ColumnswDrvCntWlanChannelBusy | read-only | current | Time in ms during which the medium has been considered busy on the current channel. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.12 | ColumnswDrvCntWlanChannelTransmit | read-only | current | Time in ms during which the device has been in transmit mode on the current channel. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.13 | ColumnswDrvCntWlanChannelReceive | read-only | current | Time in ms during which the device has been in receive mode on the current channel. Applies to AP and STA. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.14 | ColumnswDrvCntWlanChannelNoise | read-only | current | Measured channel noise in 1 dB steps. **Notice:** This value is not an absolute power level but the internal representation of the measured noise floor. Applie… |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.20 | ColumnswDrvCntWlanEapAuthStartedFT | read-only | current | EAP sessions started through FT. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.21 | ColumnswDrvCntWlanEapAuthStartedFILS | read-only | current | EAP sessions started through FILS. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.5.9.1.22 | ColumnswDrvCntWlanEapAuthStartedPKMSA | read-only | current | EAP sessions started through PKMSA. Applies to AP. 802.11n products only. |
| 1.3.6.1.4.1.16177.1.400.1.6.6 | NodeswRdm | |||
| 1.3.6.1.4.1.16177.1.400.1.6.6.1 | ScalarswRdmMaxEirp | read-only | current | Maximal equivalent isotropically radiated power (EIRP) in dBm. This value shows the maximal aggregated transmit power over all configured chains. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.6.6.2 | ScalarswRdmMaxApp | read-only | current | Maximal antenna port power in dBm. This value shows the maximal transmit power of a single chain. Applies to AP. |
| 1.3.6.1.4.1.16177.1.400.1.6.20 | NodeswBootloader | |||
| 1.3.6.1.4.1.16177.1.400.1.6.20.1 | ScalarswBootName | read-only | current | Name of the bootloader. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.20.2 | ScalarswBootVersion | read-only | current | Version of the bootloader. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.20.3 | ScalarswBootBuildDate | read-only | current | Date when the bootloader was built. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.6.30 | NodeswConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.1.6.30.1 | ScalarswCfgChangesCount | read-only | current | Number of not yet applied device configuration changes. Applies to AP and STA. |
| 1.3.6.1.4.1.16177.1.400.1.100 | Nodeconformance | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1 | Nodegroups | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1 | NodegroupConfiguration | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.1 | GroupgroupCfgSystem | current | System Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2 | NodegroupCfgNetwork | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.1 | GroupgroupCfgNetEthernet | current | Network Ethernet Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.2 | GroupgroupCfgNetWlan | current | Wireless Interface Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.3 | GroupgroupCfgNetVlan | current | VLAN Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.6 | GroupgroupCfgNetIp | current | IP Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.7 | GroupgroupCfgNetCarp | current | IP Carp Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.9 | GroupgroupCfgNetMacVLan | current | Mac Vlan Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.2.11 | GroupgroupCfgNetWwan | current | Wwan Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3 | NodegroupCfgWireless | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.1 | GroupgroupCfgWlanDevice | current | Wireless Interface Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.2 | GroupgroupCfgWlanInterface | current | Wireless Interface Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.3 | GroupgroupCfgWlanHandoff | current | Wireless Handoff Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.4 | GroupgroupCfgWlanScanFreq | current | Wireless Scanlist Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.5 | GroupgroupCfgWlanWme | current | Wireless WME properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.6 | GroupgroupCfgWlanDbg | current | Wireless Debug Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.7 | GroupgroupCfgWlanAclBlack | current | Wireless ACL Black Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.8 | GroupgroupCfgWlanAclWhite | current | Wireless ACL White Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.9 | GroupgroupCfgWlanGlobal | current | Wireless Global Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.10 | GroupgroupCfgWlan802dot1x | current | Wireless 802.1X Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.11 | GroupgroupCfgWlan802dot1xAuth | current | Wireless 802.1X Auth Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.12 | GroupgroupCfgWlan802dot1xAcct | current | Wireless 802.1X Acct Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.13 | GroupgroupCfgWlan802dot11r | current | Wireless 802.11r properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.3.14 | GroupgroupCfgWlanNeighbour | current | Wireless neighbour properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.4 | NodegroupCfgRouting | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.4.1 | GroupgroupCfgRouteDefault | current | Routing Default Route Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.4.2 | GroupgroupCfgRouteTable | current | Static Routes Group | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.4.3 | GroupgroupCfgMRouteTable | current | Static Routes Group | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.11 | GroupgroupCfgLogging | current | Logging Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.12 | NodegroupCfgSnmp | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.12.1 | GroupgroupCfgSnmpd | current | SNMP Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.12.10 | GroupgroupCfgSnmpTrap | current | SNMP Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.13 | NodegroupCfgDhcp | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.13.1 | GroupgroupCfgDhcpGlobal | current | DHCP Global Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.13.2 | GroupgroupCfgDhcpDnsmasq | current | Dnsmasq Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.13.3 | GroupgroupCfgDhcpScope | current | DHCP Individual Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.14 | GroupgroupCfgNtp | current | NTP Client Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.15 | GroupgroupCfgHttp | current | HTTP Server Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.16 | GroupgroupCfgLldp | current | HTTP Server Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.17 | GroupgroupCfgMdns | current | mDNS service properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.18 | NodegroupCfgQos | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.18.1 | GroupgroupCfgQosGlobal | current | QoS general maintree properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.18.2 | GroupgroupCfgQosDscpToTidMapTable | current | QoS L3 To L2 Map properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.18.3 | GroupgroupCfgQosVlanToTidMapTable | current | Qos Vlan To L2 Priority properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.18.4 | GroupgroupCfgQosIpToTidMapTable | current | QoS Flow Priority properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.40 | GroupgroupCfgNlm | current | Nlm properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.100 | GroupgroupCfgCli | current | CLI Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.101 | NodegroupCfgCellular | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.1.101.1 | GroupgroupCfgCellSim | current | Cellular Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.2 | NodegroupStatus | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.3 | NodegroupRpc | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.3.1 | GroupgroupRpcConfiguration | current | RPCs for Configuration | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.3.2 | GroupgroupRpcFirmware | current | RPCs for Firmware | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.3.3 | GroupgroupRpcSystem | current | RPCs for the System | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.3.4 | GroupgroupRpcCertificate | current | RPCs for HTTPS Certificate/Key | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.3.6 | GroupgroupRpcDriver | current | RPCs Software Driver | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4 | NodegroupSettings | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.1 | GroupgroupSetConfigurationFile | current | Configuration File Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.3 | GroupgroupSetWireless | current | Wireless Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.4 | GroupgroupSetWlanDbg | current | Wireless Debug Properties | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.5 | GroupgroupSetConfmgmtd | current | Configuration Manager Daemon Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.6 | GroupgroupSetFirmware | current | Firmware Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.7 | GroupgroupSetCertificate | current | HTTPS Certificate/Key File Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.4.8 | GroupgroupSetSystem | current | System Settings | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5 | NodegroupHardware | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.1 | GroupgroupHwSystem | current | Hardware System | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.2 | GroupgroupHwNetwork | current | Hardware Network | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.3 | GroupgroupHwWireless | current | Hardware Wireless | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.4 | GroupgroupHwBaseBoard | current | Hardware Base Board | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.5 | GroupgroupHwIfaceBoard | current | Hardware Interface Board | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.5.7 | GroupgroupHwSensor | current | Hardware Sensors | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6 | NodegroupSoftware | |||
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.1 | GroupgroupSwFirmware | current | Software Firmware | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.2 | GroupgroupSwSystem | current | Software System | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.3 | GroupgroupSwOperatingSystem | current | Software System | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.4 | GroupgroupSwDrvDfs | current | Software Driver DFS Statistics | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.7 | GroupgroupSwDrvCntWlanMac | current | Software Driver DFS Statistics | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.8 | GroupgroupSwDrvCntWlanWmm | current | Software Driver WMM Statistics | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.9 | GroupgroupSwDrvConStat | current | Software Driver Connection Status | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.10 | GroupgroupSwDrvCntWlanTable | current | Software Driver Wlan Counters | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.11 | GroupgroupSwRdm | current | Software RDM | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.20 | GroupgroupSwBootloader | current | Bootloader Informations | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.6.30 | GroupgroupSwConfiguration | current | Device Configuration Information | |
| 1.3.6.1.4.1.16177.1.400.1.100.1.7 | NodegroupFeatures | |||
| 1.3.6.1.4.1.16177.1.400.1.100.2 | Nodecompliances | |||
| 1.3.6.1.4.1.16177.1.400.1.100.2.1 | Compliancecompliance | current | Implementation requirements for DT50 bindings |