WIRELESS-INNOVATIONS-PRODUCTS-MIB
241 objects
MIB for Wireless Innovations distributed management system.
Imported Objects
| ANDREW-MIB | wirelessInnovations |
| ENTITY-MIB | PhysicalIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-MIB | sysName |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime TEXTUAL-CONVENTION TruthValue VariablePointer |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.331.1.2.1 | IdentitywirelessInnovationsProducts | MIB for Wireless Innovations distributed management system. | ||
| 1.3.6.1.4.1.331.1.2.1.1 | IdentitycommonDeviceObjects | current | Objects valid for common objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.1 | IdentitycommonDeviceBasic | current | Basic information. | |
| 1.3.6.1.4.1.331.1.2.1.1.1.1 | ScalarbasicAgentVersion | read-only | current | This is the software version of the agent and is determined according to the software version control rules of the particular device. |
| 1.3.6.1.4.1.331.1.2.1.1.1.2 | ScalarbasicCurrentMibVersion | read-only | current | This object denotes the current MIB's version. This value is built by the first line of the DESCRIPTION value of the most recent REVISION statement of the curr… |
| 1.3.6.1.4.1.331.1.2.1.1.1.3 | ScalarbasicWirelessInnovationsMibVersion | read-only | current | The version of the WIRELESS-INNOVATIONS-PRODUCTS-MIB, which is included in this (component specific) MIB. This value is the same as the first line of the DESCR… |
| 1.3.6.1.4.1.331.1.2.1.1.1.4 | ScalarbasicCurrentTime | read-write | current | Current time in Coordinated Universal Time (UTC) format. |
| 1.3.6.1.4.1.331.1.2.1.1.1.5 | ScalarbasicAgentIPAddress | read-write | obsolete | Note! This object is obsolete and no longer supported. New object is 'connManOrigAgentIPAddressCS'. This is the IP address of the DCM used in dial-in access. S… |
| 1.3.6.1.4.1.331.1.2.1.1.1.6 | ScalarbasicAgentIPAddressNew | accessible-for-notify | current | This OID is used in the changedIPAddressEvent only. |
| 1.3.6.1.4.1.331.1.2.1.1.1.7 | ScalarbasicAgentLocationIdentification | read-only | current | Geographic location identification of the Agent, either GPS coordinates or the serving cell identification of the Agent's wireless modem (Location Area). If th… |
| 1.3.6.1.4.1.331.1.2.1.1.1.8 | ScalarbasicAgentLocationAlias | read-only | current | Alias name of the geographic location area (zone name) where the Agent is currently in. If the Agent does not support geographic location identification, an em… |
| 1.3.6.1.4.1.331.1.2.1.1.1.9 | ScalarbasicAgentOutOfOperationArea | read-only | current | Indicates whether the Agent is currently out of operation. This may be caused e.g. by geographical location change (moving out of active areas / active zones) … |
| 1.3.6.1.4.1.331.1.2.1.1.1.10 | ScalarbasicAgentConditionChangedConfig | accessible-for-notify | current | This OID is used in the changedParameterEvent only. Indicates the condition why the changedParameterEvent was fired. 0 = user maintenance via another user inte… |
| 1.3.6.1.4.1.331.1.2.1.1.1.11 | IdentitybasicGpsData | current | GPS data and related Objects. If the Agent doesn't support GPS data at all, always 'no such object' has to be returned to any request within this section. | |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.1 | ScalargpsDataTimestamp | read-only | current | Timestamp of GPS data set reported by GPS device. |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.2 | ScalargpsZoneName | read-only | current | Zone name related to GPS position (gpsLatitude/gpsLongitude) or empty string in case the position is not within a zone. Note! In case the actual position refle… |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.3 | ScalargpsLatitude | read-only | current | Position latitude. Numeric value (decimal), positive value for north, negative for south, including a decimal point. Allowed characters '-','0'..'9','.' |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.4 | ScalargpsLongitude | read-only | current | Position longitude. Numeric value (decimal), positive value for east, negative for west, including a decimal point. Allowed characters '-','0'..'9','.' |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.5 | ScalargpsSpeed | read-only | current | Speed in km/h. Numeric value (decimal) including a decimal point. Allowed characters '0'..'9','.' |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.6 | ScalargpsBearingDegree | read-only | current | Direction in relation to north in degree. Numeric value (decimal) including a decimal point. Allowed characters '0'..'9','.' |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.7 | ScalargpsAltitude | read-only | current | Position altitude or empty string in case altitude is not available. Numeric value (decimal) including a decimal point. Allowed characters '0'..'9','.' |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.8 | ScalargpsNoOfSatellites | read-only | current | Number of used satellites (decimal). |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.50 | IdentitygpsEventData | current | Additional GPS event data. | |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.50.1 | ScalargpsEventType | accessible-for-notify | current | GPS event type. 1 = Agent has detected start moving 2 = Agent has detected stop moving 3 = Agent has entered a GPS zone 4 = Agent has left a GPS zone 5 = GPS e… |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.50.2 | ScalargpsEventTime | accessible-for-notify | current | GPS event generation time in Coordinated Universal Time (UTC) format. |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.50.3 | NotificationgpsEvent | current | Notification sent by the agent to indicate the occurrence of any type of GPS event (see gpsEventType). | |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.51 | IdentitygpsEventConfiguration | current | Additional GPS event configuration data. | |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.51.1 | ScalargpsEventEnabled | read-write | current | Object that shows resp. controls whether the GPS event notification is enabled or not. |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.51.2 | ScalargpsEventDestinationIsAlarmRecipient | read-write | current | Object that shows resp. controls whether the GPS event notification destination is the standard notification destination (true: destination is alarmRecipient) … |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.51.3 | ScalargpsEventDestination | read-write | current | Object that shows resp. controls the destination of the GPS event notification. Setting the IP address to 0.0.0.0 will also have the effect of disabling the no… |
| 1.3.6.1.4.1.331.1.2.1.1.1.11.51.4 | ScalargpsHeartbeatInterval | read-write | current | Object that shows resp. controls the GPS event heartbeat interval (in minutes). Set this object to 0 in order to disable the GPS event of type heartbeat. Set t… |
| 1.3.6.1.4.1.331.1.2.1.1.2 | IdentitycommonDeviceAlarm | current | Alarm objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.2.1 | ScalaralarmRecipient | read-write | current | The recipient of all notifications. This IP address can be changed in order to switch the recipient to another (auxiliary) recipient. It can be useful if the O… |
| 1.3.6.1.4.1.331.1.2.1.1.2.2 | ScalaralarmForwardingEnabled | read-write | current | Set this value to true(1) in order to enable alarm forwarding. Note, that the alarm recipients IP address has to be set to alarmRecipient prior to enable alarm… |
| 1.3.6.1.4.1.331.1.2.1.1.2.3 | ScalaralarmHeartbeatInterval | read-write | current | The heartbeat mechanism is an alternative to OMC polling. A heartbeatEvent notification is sent by the agent to indicate that the device and the connection are… |
| 1.3.6.1.4.1.331.1.2.1.1.2.4 | ScalaralarmSynchronize | read-write | current | This object must be set to true(1) in order to force the agent to resend all active alarms to the current manager. Setting this object to false(2) has no effec… |
| 1.3.6.1.4.1.331.1.2.1.1.2.5 | ScalaralarmTrapCounter | read-only | current | This is the counter indicating how many total notifications have been sent from the device since last bootup (or reboot). The counter is included in every priv… |
| 1.3.6.1.4.1.331.1.2.1.1.2.6 | TablealarmTable | not-accessible | current | The alarm table lists all the alarms currently active into the equipment. An entry is added to the table anytime an alarm condition raises. An entry is removed… |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1 | RowalarmEntry | not-accessible | current | Alarm table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.1 | ColumnalarmIDX | not-accessible | current | Table index to identify the instance. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.2 | ColumnalarmID | read-only | current | This is the most generic identifier of the problem. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.3 | ColumnalarmSpecificProblem | read-only | current | X733 compliance: specific problem unique code,according to a common alarm list. This unique list will be maintained at a central location. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.4 | ColumnalarmPerceivedSeverity | read-only | current | According to X733 and common alarm list: 0=indeterminate 1=critical 2=major 3=minor 4=warning 5=cleared 6=information |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.5 | ColumnalarmEventDateTime | read-only | current | X733 compatibility: time stamp for alarm condition change changes can occur on severity level (including set and clear) |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.6 | ColumnalarmEventType | read-only | current | According to X733 and common alarm list:The Event Type categorises the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.7 | ColumnalarmProbableCause | read-only | current | According to X733 and common alarm list:The Probable Cause defines further qualification of an alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.8 | ColumnalarmAdditionalText | read-only | current | According to X733 and common alarm list: The Additional Text allows a free form text description to be reported. It contains a formatted description of the ala… |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.9 | ColumnalarmEquipmentCTA | read-only | current | Must be a Common Topology Address (CTA) This represents the topological address of the equipment below the Agent and references the alarm source. It may also c… |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.10 | ColumnalarmPhysicalIndex | read-only | current | This objects carries the value of entPhysicalIndex of the affected component. |
| 1.3.6.1.4.1.331.1.2.1.1.2.6.1.11 | ColumnalarmEquipmentPointer | read-only | current | The purpose of this object is to provide a pointer (OID) into the component specific MIB that relates most directly to this particular alarm. If this alarm is … |
| 1.3.6.1.4.1.331.1.2.1.1.2.7 | ScalaralarmChangedParameterPointer | accessible-for-notify | current | This OID is used in the changedParameterEvent only. It is a pointer to a component-specific object, whose parameter was changed. It points to the highest part … |
| 1.3.6.1.4.1.331.1.2.1.1.2.8 | ScalaralarmSeveritiesSupported4Set | read-only | current | Bitcoded value indication the supported alarm severity levels within a SET via the alarmConfigTable: Bit0=indeterminate (0x01) Bit1=critical (0x02) Bit2=major … |
| 1.3.6.1.4.1.331.1.2.1.1.2.9 | TablealarmConfigTable | not-accessible | obsolete | Agent alarm configuration table. This table lists all alarms supported by the agent. It is used to read resp. change default alarm parameter settings. This set… |
| 1.3.6.1.4.1.331.1.2.1.1.2.9.1 | RowalarmConfigEntry | not-accessible | obsolete | Alarm configuration table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.9.1.1 | ColumnalarmConfig4alarmID | read-only | obsolete | Referenced alarm ID: This is the most generic identifier of the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.9.1.2 | ColumnalarmConfigSeverity | read-write | obsolete | Reading this object indicates the current level the alarm is set at. Setting this object changes the current level accordingly. Note! Severity 5=cleared in thi… |
| 1.3.6.1.4.1.331.1.2.1.1.2.10 | TablealarmUsertextTable | not-accessible | obsolete | Agent alarm user text configuration table. This table lists all alarms that support user defined text. It is used to read resp. change default alarm user text … |
| 1.3.6.1.4.1.331.1.2.1.1.2.10.1 | RowalarmUsertextEntry | not-accessible | obsolete | Alarm user text configuration table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.10.1.1 | ColumnalarmUsertext4CTA | read-only | obsolete | Referenced Common Topology Address. It may also contain optional parameters, details see textual convention CTA. |
| 1.3.6.1.4.1.331.1.2.1.1.2.10.1.2 | ColumnalarmUsertext4alarmID | read-only | obsolete | Referenced alarm ID: This is the most generic identifier of the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.10.1.3 | ColumnalarmUsertext | read-write | obsolete | User defined text for referenced alarmID at referenced CTA. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11 | IdentityalarmThresholds | current | With this section alarm thresholds are handled. If the agent doesn't support alarm threshold management at all, always 'no such object' has to be returned to a… | |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1 | TablealarmThresholdTable | not-accessible | current | This table provides threshold information for each alarm that has user-defined thresholds. Thresholds can be thought of as single or ranged. A single threshold… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1 | RowalarmThresholdEntry | not-accessible | current | Alarm threshold configuration table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.1 | ColumnalarmThreshold4CTA | read-only | current | 1st table index. Referenced Common Topology Address. In distributed systems the threshold for the same alarm may be configured different depending on the topol… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.2 | ColumnalarmThreshold4alarmID | read-only | current | 2nd table index. Referenced alarm ID: This is the most generic identifier of the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.3 | ColumnalarmThresholdIdx | read-only | current | Some alarms have just a single threshold, others have a minimum and a maximum threshold. This index identifies whether this is a single, minimum, or maximum th… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.4 | ColumnalarmThresholdDescription | read-only | current | Textual description of the referenced threshold entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.5 | ColumnalarmThresholdUnit | read-only | current | Unit of the referenced threshold entry. E.g. dB, dBm, Hz, ... or empty string. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.6 | ColumnalarmThresholdScale | read-only | current | This is the scale factor for the referenced threshold entry and only applies to simple thresholds. The value should be 0 in the case of a complex threshold. Ot… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.7 | ColumnalarmThresholdStepValue | read-only | current | This object only applies to simple thresholds. It is used to identify the discrete intermediate values of the complete threshold range from alarmThresholdMinVa… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.8 | ColumnalarmThresholdMinValueAllowed | read-only | current | Possible values: Simple thresholds with defined ranges: This is the allowed minimum value of the threshold range. Single minimum thresholds: This is the value … |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.9 | ColumnalarmThresholdMaxValueAllowed | read-only | current | Possible values: Simple thresholds with defined ranges: This is the allowed maximum value of the threshold range. Single maximum thresholds: This is the value … |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.10 | ColumnalarmThresholdActValue | read-write | current | This is the actual value of the referenced threshold entry. For simple threshold ranges, please refer to alarmThresholdMinValueAllowed and alarmThresholdMaxVal… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.1.1.11 | ColumnalarmThresholdPointerToValueLookupTableMainIndex | read-only | current | For complex alarm thresholds, this is the pointer into the alarmThresholdValueLookupTable. This object does not apply to simple thresholds and should be 0 in t… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2 | TablealarmThresholdValueLookupTable | not-accessible | current | This table contains the threshold values of those alarms with ranges that are: 1. not linear or 2. cannot be described in by the few basic parameters in alarmT… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2.1 | RowalarmThresholdValueLookupEntry | not-accessible | current | Alarm threshold value lookup table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2.1.1 | ColumnalarmThresholdLookupMainIdx | read-only | current | Main table index referenced by alarmThresholdPointerToValueLookupTableMainIndex. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2.1.2 | ColumnalarmThresholdLookupValueIdx | read-only | current | 2nd table index. References the possible threshold values. |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2.1.3 | ColumnalarmThresholdLookupValue | read-only | current | This object indicates a value that may be used to set alarmThresholdActValue for the corresponding alarm. Instances of this object must be ordered such that th… |
| 1.3.6.1.4.1.331.1.2.1.1.2.11.2.1.4 | ColumnalarmThresholdLookupValueDescription | read-only | current | This is the ascii string indicating the 'real' set value, including the units if applicable. For example if setting an external alarm polarity, this object may… |
| 1.3.6.1.4.1.331.1.2.1.1.2.12 | ScalaralarmSummary | read-only | current | System summary alarm status. Can be used for a simple system summary alarm polling. This object gets also delivered with the heartbeatEvent notification. |
| 1.3.6.1.4.1.331.1.2.1.1.2.13 | TablealarmConfig2Table | not-accessible | current | Agent alarm configuration table. This table lists all alarms supported by the agent. It is used to read resp. change default alarm parameter settings. This set… |
| 1.3.6.1.4.1.331.1.2.1.1.2.13.1 | RowalarmConfig2Entry | not-accessible | current | Alarm configuration table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.13.1.1 | ColumnalarmConfig2CTAidx | read-only | current | Referenced Common Topology Address. It may also contain optional parameters, details see textual convention CTA. |
| 1.3.6.1.4.1.331.1.2.1.1.2.13.1.2 | ColumnalarmConfig2alarmIDidx | read-only | current | Referenced alarm ID: This is the most generic identifier of the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.13.1.3 | ColumnalarmConfig2Severity | read-write | current | Reading this object indicates the current level the alarm is set at. Setting this object changes the current level accordingly. Note! Severity 5=cleared in thi… |
| 1.3.6.1.4.1.331.1.2.1.1.2.13.1.4 | ColumnalarmConfig2Latency | read-write | current | Alarm raise latency in seconds. Note: This object may not given for all alarms. |
| 1.3.6.1.4.1.331.1.2.1.1.2.14 | TablealarmUsertext2Table | not-accessible | current | Agent alarm user text configuration table. This table lists all alarms that support user defined text. It is used to read resp. change default alarm user text … |
| 1.3.6.1.4.1.331.1.2.1.1.2.14.1 | RowalarmUsertext2Entry | not-accessible | current | Alarm user text configuration table entry. |
| 1.3.6.1.4.1.331.1.2.1.1.2.14.1.1 | ColumnalarmUsertext2CTAidx | read-only | current | Referenced Common Topology Address. It may also contain optional parameters, details see textual convention CTA. |
| 1.3.6.1.4.1.331.1.2.1.1.2.14.1.2 | ColumnalarmUsertext2alarmIDidx | read-only | current | Referenced alarm ID: This is the most generic identifier of the alarm. |
| 1.3.6.1.4.1.331.1.2.1.1.2.14.1.3 | ColumnalarmUsertext2 | read-write | current | User defined text for referenced alarmID at referenced CTA. |
| 1.3.6.1.4.1.331.1.2.1.1.3 | IdentitycommonDeviceNotification | current | Notification objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.3.1 | NotificationalarmTrap | current | Trap workflow: - this notification is sent any time an alarm raises or gets cleared - no acknowledge is required if sent as trap (not valid if sent as inform) … | |
| 1.3.6.1.4.1.331.1.2.1.1.3.2 | NotificationheartbeatEvent | current | A notification sent by the agent to indicate that the device and the connection are still active. The send interval is decided by means of alarmHeartbeatInterv… | |
| 1.3.6.1.4.1.331.1.2.1.1.3.3 | NotificationchangedParameterEvent | current | If manual user changes via other interfaces than SNMP, automatic changes based on geographic location change or any operating mode change happened, this notifi… | |
| 1.3.6.1.4.1.331.1.2.1.1.3.4 | NotificationchangedIPAddressEvent | current | Used to notify a new agent IP address to the manager determined by the value of alarmRecipient resp. connVpnManagerVirtualIP. This is NOT used if the agent is … | |
| 1.3.6.1.4.1.331.1.2.1.1.3.5 | NotificationagentRebootRequiredEvent | current | This notification is sent if any configuration change by the manager requires an agent reboot. | |
| 1.3.6.1.4.1.331.1.2.1.1.3.6 | NotificationagentUpAndRunningEvent | current | This notification is sent to indicate any agent startup. V1.5.0.0 extension: - basicAgentOutOfOperationArea indicates whether the Agent is out of its operation… | |
| 1.3.6.1.4.1.331.1.2.1.1.3.7 | NotificationagentShutdownEvent | current | This notification is sent by the Agent during shutdown to indicate that the system will be 'out of service'. On reception of this notification the Manager has … | |
| 1.3.6.1.4.1.331.1.2.1.1.3.8 | NotificationchangedLocationAreaEvent | current | This notification is sent by the Agent in case of a location (zone) change that caused no other parameter changes. In case of a location (zone) change that cau… | |
| 1.3.6.1.4.1.331.1.2.1.1.4 | IdentitycommonDeviceConformance | current | Conformance objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.1 | GroupcommonDeviceBasicGroup | current | A collection of objects providing basic device status and control. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.2 | GroupcommonDeviceAlarmGroup | current | A collection of alarm information common to all devices. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.3 | GroupcommonDeviceNotificationGroup | current | A collection of notifications common to all devices. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.4 | IdentitycommonDeviceCompliance | current | Compliance objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.4.1 | CompliancecommonDeviceBasicCompliance | current | The compliance statement for all devices in this system. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.5 | GroupcommonDeviceConnectivityGroup | current | A collection of objects providing for connectivity control. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.6 | GroupcommonDeviceControlGroup | current | A collection of device control objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.97 | GroupoptionalNotificationsGroup | current | A collection of optional notifications. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.98 | GroupoptionalObjectsGroup | current | A collection of optional objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.4.99 | GroupobsoleteObjectsGroup | obsolete | This group contains all objects whose status has been changed to obsolete. | |
| 1.3.6.1.4.1.331.1.2.1.1.5 | IdentitycommonDeviceConnectivity | current | Connectivity objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.1 | ScalarconnAgentUID | read-only | current | This is the agent unique identifier. The manager uses this UID to distinguish the agents integrated in the managers database. It has to be included in every pr… |
| 1.3.6.1.4.1.331.1.2.1.1.5.2 | ScalarconnAgentMainConnectivityType | read-write | obsolete | Note! This object is obsolete and no longer supported. New objects are 'connAgentMainConnectivity' and corresponding 'connAgntOrigIfConnectionType'. Agent main… |
| 1.3.6.1.4.1.331.1.2.1.1.5.3 | ScalarconnAgentIPAddressLAN | read-write | current | This is the IP address of the agent, if the agent is connected to a LAN network. The port number is that one the agent listens for SNMP GET/SET requests. It de… |
| 1.3.6.1.4.1.331.1.2.1.1.5.4 | ScalarconnAgentMainConnectivity | read-write | current | Agent main connectivity. This identifies resp. sets the preferred interface the agent connects to the network. It depends on the agent implementation whether a… |
| 1.3.6.1.4.1.331.1.2.1.1.5.5 | ScalarconnAgentNotificationType | read-write | current | Notification type the agent uses for any event defined within commonDeviceNotification and any component specific event. See TC NotificationType. |
| 1.3.6.1.4.1.331.1.2.1.1.5.6 | ScalarconnAgentUID2 | read-only | current | This is an alternative unique identifier of the Agent. This UID can be used by the Manager to detect system replacement at Agent side (connAgentUID changed whi… |
| 1.3.6.1.4.1.331.1.2.1.1.5.7 | ScalarconnAgentWebCommunicationProtocol | read-write | current | This object indicates / controls which web communication protocol is active at the Agent. This setting applies to any HTTP based communication: Agent standard … |
| 1.3.6.1.4.1.331.1.2.1.1.5.8 | ScalarconnAgentInformTimeout | read-write | current | This object shows/controls the timeout (in seconds) used by the Agent waiting for inform responses before resending. Valid values are: 10s, 20s, 30s, 40s, 50s,… |
| 1.3.6.1.4.1.331.1.2.1.1.5.9 | ScalarconnAgentInformRetries | read-write | current | This object shows/controls the number of retries used by the Agent in case inform resending. Allowed range is 1 to 20 times or -1. The value of -1 indicates re… |
| 1.3.6.1.4.1.331.1.2.1.1.5.10 | IdentityconnManagerOriginated | current | Connectivity objects for connections initiated by the manager. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.10.1 | ScalarconnManOrigAgentIPAddressCS | read-write | current | This is the IP address of the agent, if the agent gets accessed by an incoming circuit switched call (address of the agent dial-in server). The port number is … |
| 1.3.6.1.4.1.331.1.2.1.1.5.10.2 | ScalarconnManOrigAuthUsernameCS | read-write | current | This is the username for PPP authentication, if the agent gets accessed by an incoming circuit switched call. It depends on the agent implementation whether a … |
| 1.3.6.1.4.1.331.1.2.1.1.5.10.3 | ScalarconnManOrigAuthPasswordCS | read-write | current | This is the password for PPP authentication, if the agent gets accessed by an incoming circuit switched call. For security reasons it is highly recommended tha… |
| 1.3.6.1.4.1.331.1.2.1.1.5.10.4 | ScalarconnManOrigIdleTimeoutCS | read-write | current | Communication idle timeout in minutes for agent incoming circuit switched connections. When expires the agent should drop the incoming circuit switched connect… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11 | IdentityconnAgentOriginated | current | Connectivity objects for connections initiated by the agent. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1 | TableconnAgntOrigIfTable | not-accessible | current | Agent connectivity interface table. This table lists all possible interfaces that can be used for network connections at agent side. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1 | RowconnAgntOrigIfEntry | not-accessible | current | Interface table entry. It depends on the agent implementation and connectivity type whether all the table entry objects are used at all resp. how it is interpr… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.1 | ColumnconnAgntOrigIfIndex | read-only | current | Table index. Also used to indicate the priority for interfaces of the same network type. Lower indexes indicate higher priority. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.2 | ColumnconnAgntOrigIfConnectivityType | read-only | obsolete | Note! This object is obsolete and no longer supported. New objects are 'connAgntOrigIfNetworkType' and 'connAgntOrigIfConnectionType'. Connectivity type of thi… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.3 | ColumnconnAgntOrigIfEnabled | read-write | current | This object shows/controls whether this interface is enabled or disabled. It also shows whether or not such control is applicable. A GET may return: notApplica… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.4 | ColumnconnAgntOrigIfExtraSetting | read-write | current | Depending on network type, used for: - CS, PS: modem / network initialization string. - SMS: SMS prefix. - DC, LAN: not used. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.5 | ColumnconnAgntOrigIfPhoneNo | read-write | current | Depending on network type, e.g. used for: - circuit switched dial-out PPP connections: Telephone number of the recipient for all notifications. - packet switch… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.6 | ColumnconnAgntOrigIfAuthUsername | read-write | current | Username. Depending on network type, e.g. used for: - circuit switched dial-out PPP connections: This string is used to authenticate the user's access to the O… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.7 | ColumnconnAgntOrigIfAuthPassword | read-write | current | Password, for security reasons it is highly recommended that reading this object returns 14 asterisk character '**************'. Depending on network type, e.g… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.8 | ColumnconnAgntOrigIfNetworkType | read-only | current | Network type of this interface. See TC NetworkType. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.1.1.9 | ColumnconnAgntOrigIfConnectionType | read-write | current | Connection type of this interface. See TC ConnectionType. This object shows/controls the connection type of this interface. It also shows whether or not such c… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.2 | ScalarconnAgntOrigIdleTimeoutPSODreqBySMS | read-write | current | Communication idle timeout in minutes for agent side 'On Demand' packet switched network connection. Note! This applies ONLY when the connect request was issue… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.3 | ScalarconnAttachPSODrequesterSMS | accessible-for-notify | current | This OID is used in the changedIPAddressEvent only. If the agent is connected PSOD and the connection to the packet data network access server was invoked by a… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.4 | ScalarconnAttachPSODbySMSenabled | read-write | current | Shows/sets whether SMS initiated packet switched network connection in the 'On demand' mode is enabled or disabled. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.5 | ScalarconnAgentSMSserviceCenter | read-write | current | SMS service center number. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.6 | ScalarconnAgentDisconnectTrigger | read-write | current | With this object the manager is able to force a disconnect of an active agent originated network connection. A GET always returns notApplicable(0). A SET to no… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7 | IdentityconnAgentVpn | current | VPN communication objects. If the agent doesn't support VPN at all, always 'no such object' has to be returned to any request within this section. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.1 | ScalarconnVpnEnabled | read-write | current | This object shows/controls whether VPN communication is enabled or disabled. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.2 | ScalarconnVpnServerPhysicalIP | read-only | current | Physical IP address and port of actually connected VPN server. In case VPN is actually not connected, '0.0.0.0' will be responded. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.3 | ScalarconnVpnManagerVirtualIP | read-write | current | Virtual VPN IP address and port of the recipient of all notifications in case VPN is enabled. Otherwise alarmRecipient (physical IP address) is used. Note! In … |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.4 | ScalarconnVpnAgentIPIsVirtual | accessible-for-notify | current | This OID is used in the changedIPAddressEvent only, see also description there. Indicates whether the reported IP address is a virtual VPN address or not. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.5 | IdentityconnAndrewVpn | current | Andrew VPN objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.5.1 | ScalarconnAndrewVpnEncryptionType | read-write | current | Encryption type for transferred data except keep alive packet. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.5.2 | ScalarconnAndrewVpnAuthUsername | read-write | current | VPN authentication user name. This string is used to authenticate the access to the VPN server. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.5.3 | ScalarconnAndrewVpnAuthPassword | read-write | current | VPN authentication password. This string is used to authenticate the access to the VPN server. For security reasons it is highly recommended that reading this … |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.5.4 | ScalarconnAndrewVpnKeepAliveTime | read-write | current | Keep alive interval in seconds. Cyclic I am alive communication between VPN client and server. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.6 | IdentityconnOpenVpn | current | Open VPN objects. | |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.6.1 | ScalarconnOpenVpnProtocol | read-write | current | Protocol for communicating with OpenVPN server - UDP or TCP. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.7 | ScalarconnVpnClientVirtualIP | read-only | current | Actual virtual IP address of the Agent (VPN client). In case VPN is currently not connected, 0.0.0.0 has to be responded. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.8 | ScalarconnVpnNotificationDestinationIsAlarmRecipient | read-write | current | Object that shows resp. controls in case of VPN connection whether the destination for all notifications is the standard notification destination (true: destin… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.9 | ScalarconnVpnConnectionMode | read-only | current | Object that shows whether the current VPN mode is secure (vpnConnected) or in unsecure fallback mode (vpnFailed). unknownOrNotApplicable is used in case VPN is… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10 | IdentityconnVpnServerGroups | current | Objects handling VPN server groups. Due to server scalability and failover aspects more than one server may be used. The server groups identify the different s… | |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.1 | ScalarconnVpnServerAssignState | read-only | current | Object that shows whether the Agent/VPN client is assigned to a VPN server group. unknownOrNotApplicable is used in case VPN is disabled. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.2 | ScalarconnVpnAssignedServerGroupNo | read-only | current | Object that shows the actual assigned VPN server group number (>0) or 0 in case VPN server is not assigned. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.3 | ScalarconnVpnAssignedServerType | read-only | current | Object that shows whether the Agent/VPN client is actually connected to resp. currently trying to connect the main or backup VPN server. unknownOrNotApplicable… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.10 | TableconnVpnServerGroupTable | not-accessible | current | Table that holds VPN server groups. Due to scalability aspects more than one entry may be used. This table identifies the different server group instances of t… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.10.1 | RowconnVpnServerGroupEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.10.1.1 | ColumnconnVpnServerGroupIdx | read-only | current | Table index to identify the instance. Corresponds with VPN server group number. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.10.1.2 | ColumnconnVpnServerMainIP | read-write | current | Main VPN server physical IP address and port. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.10.10.1.3 | ColumnconnVpnServerBackupIP | read-write | current | Backup VPN server physical IP address and port. |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.7.11 | ScalarconnVpnDisconnectTrigger | read-write | current | With this object the manager is able to force an immediate VPN disconnect. A GET always returns notApplicable(0). A SET to notApplicable(0) has no affect and t… |
| 1.3.6.1.4.1.331.1.2.1.1.5.11.8 | ScalarconnAgntOrigAlwaysOnInactivityTimer | read-write | current | Communication idle timeout (related to application oriented incoming data requests) in minutes for agent outgoing always on connections. When expired the agent… |
| 1.3.6.1.4.1.331.1.2.1.1.5.12 | TableconnAgentSmsWlTable | not-accessible | current | Agent SMS whitelist table. This table lists all accepted SMS numbers for incoming SMS requests. |
| 1.3.6.1.4.1.331.1.2.1.1.5.12.1 | RowconnAgentSmsWlEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.331.1.2.1.1.5.12.1.1 | ColumnconnAgentSmsWlIndex | read-only | current | Table index to identify the instance. |
| 1.3.6.1.4.1.331.1.2.1.1.5.12.1.2 | ColumnconnAgentSmsWlNumber | read-write | current | Authorized SMS phone number for incoming SMS requests. |
| 1.3.6.1.4.1.331.1.2.1.1.5.13 | ScalarconnAgentZoneChangeNotificationsEnabled | read-write | current | This object shows/controls whether all location area change based notifications are enabled or not. Location area change based notifications are: - changedPara… |
| 1.3.6.1.4.1.331.1.2.1.1.6 | IdentitycommonDeviceControl | current | Device and agent application control objects. Objects in this group provide for resetting of remote devices. In the future, other control such as software down… | |
| 1.3.6.1.4.1.331.1.2.1.1.6.1 | ScalarctrlApplication | read-write | current | This object allows the agent application to be reset and if needed, the operating system as well. A GET must return running(0). A SET to reboot(1) causes a com… |
| 1.3.6.1.4.1.331.1.2.1.1.7 | IdentitycommonDeviceFeatureKeys | current | With this section software features of the agent are handled. If the agent doesn't support software feature keys at all, always 'no such object' has to be retu… | |
| 1.3.6.1.4.1.331.1.2.1.1.7.1 | TablefeatureKeyTable | not-accessible | current | This table lists all possible SW features supported by the agent. |
| 1.3.6.1.4.1.331.1.2.1.1.7.1.1 | RowfeatureKeyEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.331.1.2.1.1.7.1.1.1 | ColumnfeatureKeyIdx | not-accessible | current | Table index. |
| 1.3.6.1.4.1.331.1.2.1.1.7.1.1.2 | ColumnfeatureKeyDescription | read-only | current | Textual description of the feature. |
| 1.3.6.1.4.1.331.1.2.1.1.7.1.1.3 | ColumnfeatureKeyEnabled | read-only | current | This object shows whether the feature is enabled or not. |
| 1.3.6.1.4.1.331.1.2.1.1.7.2 | ScalarfeatureKeyNew | read-write | current | With this object a new SW feature can be enabled by writing a valid feature key. A GET always returns an empty string. A SET with an invalid feature key result… |
| 1.3.6.1.4.1.331.1.2.1.1.8 | IdentitycommonDeviceFileTransfer | current | Objects for file transfer control. The actual file transfer is done via HTTP. In this section the following naming definition applies: - file upload: file tran… | |
| 1.3.6.1.4.1.331.1.2.1.1.8.1 | IdentityfUpload | current | Objects for file upload control. The actual file transfer is done via HTTP POST. If the Agent doesn't support file upload at all, always 'no such object' has t… | |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.1 | ScalarfulState | read-write | current | File upload state. idle: State idle indicates that no file upload is active. Initial and final state. State transition back to idle is always initiated by the … |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.2 | ScalarfulSegmentationSupported | read-only | current | Indicates whether the Agent supports segmented file upload or not. |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.3 | ScalarfulFilename | read-write | current | Name of file to upload. Set only allowed if fulState = preparation. |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.4 | ScalarfulMD5 | read-write | current | 128 bit MD5 hash of file to upload represented as a sequence of 32 hexadecimal lowercase characters. Set only allowed if fulState = preparation. |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.5 | ScalarfulUploadURL | read-only | current | URL for file upload to be used by the Manager together with the HTTP POST command. |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.6 | ScalarfulResultOk | read-only | current | File upload result, indicates whether file upload was successful or not. Value only valid if fulState = md5checkDone or any state transition responded an error… |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.7 | ScalarfulResultString | read-only | current | Detailed description of file upload result. Syntax: 'E'(rror)|'W'(arning)|'I'(nfo)+': <Result text>' or empty string. Possible result strings (examples): - 'I:… |
| 1.3.6.1.4.1.331.1.2.1.1.8.1.8 | ScalarfulDestFolder | read-write | current | V1.5.0.0 extension: Destination folder of file to upload. If the folder does not yet exist, the Agent has to create it during the SET request. Path separator c… |
| 1.3.6.1.4.1.331.1.2.1.1.9 | IdentitycommonDeviceSwUpdateActivationRemoval | current | Objects to control Agent software update, activation or removal. If the Agent doesn't support software update/activation/removal at all, always 'no such object… | |
| 1.3.6.1.4.1.331.1.2.1.1.9.1 | ScalarswActivePackageVersion | read-only | current | Version of the actual active SW package at the Agent. Typically this version is equal to basicAgentVersion but e.g. in distributed systems it may differ. |
| 1.3.6.1.4.1.331.1.2.1.1.9.2 | ScalarswActivePackagePatchLevel | read-only | current | Patch level of the actual active SW package at the Agent. |
| 1.3.6.1.4.1.331.1.2.1.1.9.3 | TableswPackagesTable | not-accessible | current | This table lists all SW packages that are available at the Agent. |
| 1.3.6.1.4.1.331.1.2.1.1.9.3.1 | RowswPackagesEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.331.1.2.1.1.9.3.1.1 | ColumnswPackagesIdx | not-accessible | current | Table index. |
| 1.3.6.1.4.1.331.1.2.1.1.9.3.1.2 | ColumnswPackagesAvailable | read-only | current | Version of available SW package. |
| 1.3.6.1.4.1.331.1.2.1.1.9.3.1.3 | ColumnswPackagesPatchlevel | read-only | current | Patch level of available SW package. |
| 1.3.6.1.4.1.331.1.2.1.1.9.4 | ScalarswState | read-write | current | SW update / activation / removal state. idle: State idle indicates that no SW update / activation / removal is active. Initial state. State transition back to … |
| 1.3.6.1.4.1.331.1.2.1.1.9.5 | ScalarswPackageVersion | read-write | current | Version of new SW package to be updated / activated / removed. |
| 1.3.6.1.4.1.331.1.2.1.1.9.6 | ScalarswPackagePatchLevel | read-write | current | Patch level of new SW package to be updated / activated / removed. |
| 1.3.6.1.4.1.331.1.2.1.1.9.7 | ScalarswActivationForced | read-write | current | SW package activation 'force' option. |
| 1.3.6.1.4.1.331.1.2.1.1.9.8 | ScalarswStateResultOk | read-only | current | Actual state result, indicates whether transition to actual state was successful or not. Value only valid if swState = versionRsp or versionActivationOrRemoval… |
| 1.3.6.1.4.1.331.1.2.1.1.9.9 | ScalarswStateResultString | read-only | current | Detailed description of actual state result. Syntax: 'E'(rror)|'W'(arning)|'I'(nfo)+': <Result text>' or empty string. Possible result strings (examples): - 'I… |
| 1.3.6.1.4.1.331.1.2.1.1.9.10 | TableswNeededFilesTable | not-accessible | current | This table lists all files of the new SW package that are not yet available at the Agent. V1.5.3.0 extension: - immediate file activation after upload introduc… |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1 | RowswNeededFilesEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1.1 | ColumnswNeededFilesIdx | not-accessible | current | Table index. |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1.2 | ColumnswNeededFilesFilename | read-only | current | Name of a needed file which is part of the new SW package. |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1.3 | ColumnswNeededFilesFolder | read-only | current | Corresponding folder for swNeededFilesFilename. Path separator character is the slash '/'. This is a relative path (no leading slash) within the new SW package… |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1.4 | ColumnswNeededFilesImmediateActivationRequired | read-only | current | This object identifies whether the file needs immediate activation after upload or not. If this object is not available, the Manager has to assume false. |
| 1.3.6.1.4.1.331.1.2.1.1.9.10.1.5 | ColumnswNeededFilesImmediateActivationSync | read-only | current | In case swNeededFilesImmediateActivationRequired is true, this object identifies the file activation finished synchronization notification, sent out by the Age… |
| 1.3.6.1.4.1.331.1.2.1.1.9.11 | ScalarswFinalActivationNotification | read-only | current | This object identifies the final SW package activation finished notification, sent out by the Agent at the end of a SW package activation when all steps of the… |
| 1.3.6.1.4.1.331.1.2.1.1.9.20 | NotificationswActivationProgress | current | This notification is sent to provide SW package activation progress information to the Manager. Progress information strings during activation come with swStat… | |
| 1.3.6.1.4.1.331.1.2.1.2 | IdentitygroupNodeM | current | Placeholder for all Node products. | |
| 1.3.6.1.4.1.331.1.2.1.3 | IdentitygroupBCELL | current | Placeholder for all Brite-Cell products. | |
| 1.3.6.1.4.1.331.1.2.1.4 | IdentitygroupAMR | current | Placeholder for all AMR products. | |
| 1.3.6.1.4.1.331.1.2.1.5 | IdentitygroupMiniRepeater | current | Placeholder for all miniRepeater products | |
| 1.3.6.1.4.1.331.1.2.1.6 | IdentitygroupION | current | Placeholder for all ION products. | |
| 1.3.6.1.4.1.331.1.2.1.6.1 | IdentityionM | current | ION-M section. | |
| 1.3.6.1.4.1.331.1.2.1.6.2 | IdentityionB | current | ION-B section. | |
| 1.3.6.1.4.1.331.1.2.1.6.3 | IdentityionU | current | ION-U section. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AlarmDescrString | OCTET STRING (SIZE (0..128)) | current | An octet string containing alarm description information in human-readable form. |
| ConnectionType | INTEGER { notApplicable(0), onDemand(1), alwaysOn(2) } | current | Actual type of connection the agent is connected to the network. 0= Not applicable for the network type 1='On Demand' 2='Always On' |
| ConnectivityType | INTEGER { csod(1), csao(2), psod(3), psao(4), dcod(5), dcao(6), sms(7), lan(8) } | current | Type of connection the agent is connected to the network. 1=CSOD (Circuit Switched network, 'On Demand') 2=CSAO (Circuit Switched network, 'Always On') 3=PSOD (Packet Switched network, 'On Demand') 4=PSAO (Packet Switch… |
| CTA | OCTET STRING (SIZE (1..64)) | current | This is the Common Topology Address and is built in a hierarchical form: First_level_add, second_level_add, third_level_add,.... Syntax is <integer>.<integer>.<integer>.... V1.2.2.0 extension: There are cases where ther… |
| EventType | INTEGER { communications(1), qualityOfService(2), processingError(3), equipment(4), environmental(5) } | current | The event type of an alarm. See also: - ISO/IEC 10164-4, chapter 8.1.1 - ISO/IEC 10165-2, chapter 14.2 |
| IPAddressAndPort | OCTET STRING (SIZE (7..21)) | current | An IP address with up to 21 characters in the format a.b.c.d:port, e.g. 192.168.1.2:164. If the port is omitted, then the colon must also be omitted. Note! In future versions this may be extended to support IPv6 address… |
| NetworkType | INTEGER { cs(1), ps(2), dc(3), sms(4), lan(5) } | current | Network type. 1=CS (Circuit Switched network) 2=PS (Packet Switched network) 3=DC (circuit switched Direct Connection over serial line) 4=SMS (Short Message Service) 5=LAN (Local Area Network) |
| NotificationType | INTEGER { trap(1), inform(2) } | current | Notification type used for outgoing notifications. 1=SNMP trap 2=SNMP inform |
| PositiveIntegerButNotZero | Integer32 (1..2147483647) | current | All integers > 0 |
| PositiveIntegerIncludingZero | Integer32 (0..2147483647) commonDeviceObjects OBJECT-IDENTITY STATUS current DESCRIPTION "Objects valid for common objects." ::= { wirelessInnovationsProducts 1 } commonDeviceBasic OBJECT-IDENTITY STATUS current DESCRIPTION "Basic information." ::= { commonDeviceObjects 1 } | current | All integers >= 0 |
| ProbableCause | INTEGER { unknown(0), adapterError(1), applicationSubsystemFailure(2), bandwidthReduced(3), callEstablishmentError(4), communicationsProtocolError(5), communicationsSubsystemFailure(6), configurationOrCustomizationError(7), congestion(8), corruptData(9), cpuCyclesLimitExceeded(10), dTEDCEInterfaceError(11), dataSetOrModemError(12), degradedSignal(13), enclosureDoorOpen(14), equipmentMalfunction(15), excessiveVibration(16), fileError(17), fireDetected(18), floodDetected(19), framingError(20), heatingOrVentilationOrCoolingSystemProblem(21), humidityUnacceptable(22), inputOutputDeviceError(23), inputDeviceError(24), lANError(25), leakDetected(26), localNodeTransmissionError(27), lossOfFrame(28), lossOfSignal(29), materialSupplyExhausted(30), multiplexerProblem(31), outOfMemory(32), outputDeviceError(33), performanceDegraded(34), powerProblem(35), pressureUnacceptable(36), processorProblem(37), pumpFailure(38), queueSizeExceeded(39), receiveFailure(40), receiverFailure(41), remoteNodeTransmissionError(42), resourceAtOrNearingCapacity(43), responseTimeExcessive(44), retransmissionRateExcessive(45), softwareError(46), softwareProgramAbnormallyTerminated(47), softwareProgramError(48), storageCapacityProblem(49), temperatureUnacceptable(50), thresholdCrossed(51), timingProblem(52), toxicLeakDetected(53), transmitFailure(54), transmitterFailure(55), underlyingResourceUnavailable(56), versionMismatch(57), snmpTrapColdStart(100), snmpTrapWarmStart(101), snmpTrapLinkDown(102), snmpTrapLinkUp(103), snmpTrapAuthenticationFailure(104), snmpTrapEgpNeighborloss(105), snmpTrapEnterpriseSpecific(106), snmpTrapLinkUpDown(107) } | current | See ISO/IEC 10164-4, chapter 8.1.2.1 |
| Severity | INTEGER { indeterminate(0), critical(1), major(2), minor(3), warning(4), cleared(5), information(6) } | current | According to X733 and common alarm list: 0=indeterminate 1=critical 2=major 3=minor 4=warning 5=cleared 6=information |
| Severity4Set | INTEGER (-128..127) | current | Bitcoded value indication the supported alarm severity levels within a SET: Bit0=indeterminate (0x01) Bit1=critical (0x02) Bit2=major (0x04) Bit3=minor (0x08) Bit4=warning (0x10) Bit5=disable (0x20) Bit6=information (0x… |
| SpecificProblem | Unsigned32 (0..65535) | current | Specific Problem is defined in accordance with definitions given in ITU-T Recommendation X.733 clause 8.1.2.2. The list of Specific Problem codes for Wireless Innovations Products is maintained in Buchdorf. |
| Version | OCTET STRING (SIZE (0 | 5..15)) | current | Hierarchical nested major and minor version, release, and build identification. Syntax: '<major>.<minor>.<release>.<build>' or empty string. Each part has 1 up to 3 digits (0-9), '.<build>' at the end is optional. Examp… |