WL400-DOT11EXT-MIB
99 objects
The 802.11 Extension MIB module.
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | BITS Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | MacAddress RowStatus TruthValue |
| WL400-GLOBAL-REG | wl400Modules wl400Products |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.232.143.1.2 | Identitydot11ExtMibModule | The 802.11 Extension MIB module. | ||
| 1.3.6.1.4.1.232.145.1 | Nodedot11ExtMIB | |||
| 1.3.6.1.4.1.232.145.1.1 | Nodedot11ExtConf | |||
| 1.3.6.1.4.1.232.145.1.1.1 | Nodedot11ExtGroups | |||
| 1.3.6.1.4.1.232.145.1.1.1.1 | GroupsmtGroup | current | The additional objects for Station Management | |
| 1.3.6.1.4.1.232.145.1.1.1.2 | GroupassocGroup | current | The association group | |
| 1.3.6.1.4.1.232.145.1.1.1.3 | GroupsecurityGroup | current | The security group | |
| 1.3.6.1.4.1.232.145.1.1.1.4 | GroupsecNotificationGroup | current | The security-related notifications. | |
| 1.3.6.1.4.1.232.145.1.1.1.5 | GrouproamGroup | current | The roaming group | |
| 1.3.6.1.4.1.232.145.1.1.2 | Nodedot11ExtCompl | |||
| 1.3.6.1.4.1.232.145.1.1.2.1 | Compliancedot11ExtBasicCompl | current | The implementation requirements for an IEEE 802.11 Station. | |
| 1.3.6.1.4.1.232.145.1.1.2.2 | Compliancedot11ExtAPCompl | current | The implementation requirements for an Access Point. | |
| 1.3.6.1.4.1.232.145.1.1.2.3 | Compliancedot11ExtWBUCompl | current | The implementation requirements for a WBU. | |
| 1.3.6.1.4.1.232.145.1.2 | Nodedot11ExtGenObjs | |||
| 1.3.6.1.4.1.232.145.1.2.1 | Nodesmt | |||
| 1.3.6.1.4.1.232.145.1.2.1.1 | ScalarsmtAssociationID | read-only | current | The Association ID of an association between an Access Point and a Station. The size constraint is taken from IEEE 802.11 section 7.3.1.8. For an Access Point,… |
| 1.3.6.1.4.1.232.145.1.2.1.2 | ScalarsmtCapabilityInfo | read-only | current | The Capability Information of this entity. |
| 1.3.6.1.4.1.232.145.1.2.1.3 | ScalarsmtPowerSaveInterval | read-write | current | The time limit, in units of beacon intervals, after which the Client will go into Power Save Mode if the Client does not detect activity. For an Access Point, … |
| 1.3.6.1.4.1.232.145.1.2.1.4 | ScalarsmtListenInterval | read-write | current | The time, in units of beacon intervals, that may pass before the Client awakens and listens for the next Beacon. For an Access Point, this object is always zer… |
| 1.3.6.1.4.1.232.145.1.2.1.5 | ScalarsmtATIMWindow | read-write | current | The duration of the ATIM Window, in TUs. For an Access Point, this object is always zero. |
| 1.3.6.1.4.1.232.145.1.2.1.6 | ScalarsmtOperationalChannels | read-write | current | The list of DS channels that shall be scanned with a higher priority. All channels allowed by the current regulatory domain are scanned, the channels specified… |
| 1.3.6.1.4.1.232.145.1.2.1.7 | ScalarsmtCurrentBSSID | read-only | current | The current Basic Service Set ID. For a Client, this object either contains the BSSID of the Access Point with which the Client is associated or the BSSID of t… |
| 1.3.6.1.4.1.232.145.1.2.1.8 | ScalarsmtCurrentSSID | read-only | current | The current Service Set ID. For a Client, this object either contains the SSID of the infrastructure network or the SSID of the IBSS it currently associated wi… |
| 1.3.6.1.4.1.232.145.1.2.1.9 | ScalarsmtCurrentBSSType | read-only | current | The type of the Basic Service Set. For a Client, this object indicates the type of SS it currently is associated with, participating in. For an Access Point, t… |
| 1.3.6.1.4.1.232.145.1.2.1.10 | ScalarsmtPublicKeyEnable | read-write | current | This object specifies whether public-key techniques shall be used to negotiate keys. |
| 1.3.6.1.4.1.232.145.1.2.1.11 | ScalarsmtQualityLevel0 | read-write | current | This object relates quality level to a transmission rate. Level 0 specifies the lowest (basic) rate. |
| 1.3.6.1.4.1.232.145.1.2.1.12 | ScalarsmtQualityLevel1 | read-write | current | This object relates quality level to a transmission rate. Level 1 specifies the second lowest (basic) rate. |
| 1.3.6.1.4.1.232.145.1.2.1.13 | ScalarsmtQualityLevel2 | read-write | current | This object relates quality level to a transmission rate. Level 2 specifies the an arbitrary (higher) rate. |
| 1.3.6.1.4.1.232.145.1.2.1.14 | ScalarsmtQualityPenalty | read-write | current | This object specifies a quality penalty for transmission failures. |
| 1.3.6.1.4.1.232.145.1.2.1.15 | ScalarsmtStationDBTimeout | read-write | current | This object specifies a timeout on entries and their state information in the Station database. For Clients the Station database is mapped on the roamTable. Fo… |
| 1.3.6.1.4.1.232.145.1.2.1.16 | ScalarsmtQualityIndicator | read-write | current | This object selects the quality indicator from the baseband. Current quality indicators are: 1 = Signal Quality 1 (SQ1) 2 = Signal Quality 2 (SQ2) 3 = Signal Q… |
| 1.3.6.1.4.1.232.145.1.2.1.17 | ScalarsmtQualityUpperLimit | read-write | current | An upper limit for the quality. |
| 1.3.6.1.4.1.232.145.1.2.1.18 | ScalarsmtQualityLowerLimit | read-write | current | A lower limit for the quality. |
| 1.3.6.1.4.1.232.145.1.2.1.19 | ScalarsmtOEMCapabilityInformation | read-only | current | The OEM Capability Information. |
| 1.3.6.1.4.1.232.145.1.2.1.20 | ScalarsmtCWMin | read-write | current | The CWMin value as defined by IEEE 802.11. Needs to be a power of 2, minus 1. |
| 1.3.6.1.4.1.232.145.1.2.1.21 | ScalarsmtCWMax | read-write | current | The CWMax value as defined by IEEE 802.11. Needs to be a power of 2, minus 1, larger than or equal to smtCWMin. |
| 1.3.6.1.4.1.232.145.1.2.1.22 | ScalarsmtACKWindow | read-write | current | The ACK frame time out defined in number of slottimes. This can be used to optimize long range links. |
| 1.3.6.1.4.1.232.145.1.3 | Nodedot11ExtAPObjs | |||
| 1.3.6.1.4.1.232.145.1.3.1 | Nodeassoc | |||
| 1.3.6.1.4.1.232.145.1.3.1.1 | ScalarassocTableMaxLength | read-only | current | This object specifies the maximum number of associations the assocTable can hold. |
| 1.3.6.1.4.1.232.145.1.3.1.2 | TableassocTable | not-accessible | current | The Association table. This table contains all the Clients associated with the Access Point. The index of the entry equals the Association ID of the Client wit… |
| 1.3.6.1.4.1.232.145.1.3.1.2.1 | RowassocEntry | not-accessible | current | An entry in the Association Table. |
| 1.3.6.1.4.1.232.145.1.3.1.2.1.1 | ColumnassocIndex | not-accessible | current | The index into the association table. The index equals the association ID that is in use for the Client. |
| 1.3.6.1.4.1.232.145.1.3.1.2.1.2 | ColumnassocAddress | read-only | current | MAC address of a Client associated with the Access Point. If the association is pending (that is, the Client is scanning, authenticating or associating), assoc… |
| 1.3.6.1.4.1.232.145.1.3.1.2.1.3 | ColumnassocQuality | read-only | current | An indicator for the quality of the Client. If the association is still pending, the quality is calculated over the received Probe Requests from the Client. If… |
| 1.3.6.1.4.1.232.145.1.3.1.2.1.4 | ColumnassocAge | read-only | current | An indicator (in seconds) for the age of the information on the Client. The age is reset to 0 if any activity of this Client is detected. |
| 1.3.6.1.4.1.232.145.1.3.1.2.1.5 | ColumnassocRSSI | read-only | current | An indicator for the RSSI of the Client. If the association is still pending, the RSSI is calculated over the received Probe Requests from the Client. If the C… |
| 1.3.6.1.4.1.232.145.1.3.2 | Nodesecurity | |||
| 1.3.6.1.4.1.232.145.1.4 | Nodedot11ExtEvents | |||
| 1.3.6.1.4.1.232.145.1.4.0 | Nodedot11ExtEventsV2 | |||
| 1.3.6.1.4.1.232.145.1.4.0.1 | NotificationsecurityViolation | current | A security violation was detected. The secLastErrorCode indicates the type of error/violation, the secLastErrorAddress indicates the involved MAC address. | |
| 1.3.6.1.4.1.232.145.1.5 | Nodedot11ExtWBUObjs | |||
| 1.3.6.1.4.1.232.145.1.5.1 | Noderoam | |||
| 1.3.6.1.4.1.232.145.1.5.1.1 | ScalarroamScanType | read-write | current | This object configures the type of scanning the Client uses. |
| 1.3.6.1.4.1.232.145.1.5.1.2 | ScalarroamScanInterval | read-write | current | The interval, in units of beacon intervals, between successive scans during an association. |
| 1.3.6.1.4.1.232.145.1.5.1.3 | ScalarroamProbeDelay | read-write | current | This object specifies the delay (in ms) to be used prior to transmitting a Probe frame during active scanning. The object implements the ProbeDelay parameter o… |
| 1.3.6.1.4.1.232.145.1.5.1.4 | ScalarroamMinChannelTime | read-write | current | This object specifies the minimum time (in time units) to spend on each channel when scanning. The object implements the MinChannelTime parameter in the MLME-S… |
| 1.3.6.1.4.1.232.145.1.5.1.5 | ScalarroamMaxChannelTime | read-write | current | This object specifies the maximum time (in time units) to spend on each channel when scanning. The object implements the MaxChannelTime parameter in the MLME-S… |
| 1.3.6.1.4.1.232.145.1.5.1.6 | ScalarroamJoinTimeout | read-write | current | The firmware will keep trying to find a suitable BSS until another MLME-JOIN.request is issued. The object roamJoinTimeout allows the application to estimate h… |
| 1.3.6.1.4.1.232.145.1.5.1.7 | ScalarroamBeaconPeriodTimeout | read-write | current | The time limit, in units of beacon intervals, after which the association is voided if no beacons are received. |
| 1.3.6.1.4.1.232.145.1.5.1.8 | ScalarroamDontSwitch | read-write | current | The time limit, in units of beacon intervals, during which the Client will not use BSS quality parameters for making the roaming decissions if it becomes assoc… |
| 1.3.6.1.4.1.232.145.1.5.1.9 | ScalarroamBlackout | read-write | current | The time, in units of beacon intervals, during which the BSS is not considered candidate after the association was denied or voided. |
| 1.3.6.1.4.1.232.145.1.5.1.10 | ScalarroamDisassociateTime | read-write | current | The time, in units of beacon intervals, taken by the Disassociate procedure. |
| 1.3.6.1.4.1.232.145.1.5.1.11 | ScalarroamHandoffTime | read-write | current | Time, in time units, during which data to the Access Point is hold before a handoff is performed. |
| 1.3.6.1.4.1.232.145.1.5.1.12 | ScalarroamWeightMetric1 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.13 | ScalarroamWeightMetric2 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.14 | ScalarroamWeightMetric3 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.15 | ScalarroamWeightMetric4 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.16 | ScalarroamWeightMetric5 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.17 | ScalarroamWeightMetric6 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.18 | ScalarroamWeightMetric7 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.19 | ScalarroamWeightMetric8 | read-write | current | A metric used to make roaming decisions. |
| 1.3.6.1.4.1.232.145.1.5.1.20 | ScalarroamMisc1 | read-write | current | A misc roaming value. |
| 1.3.6.1.4.1.232.145.1.5.1.21 | ScalarroamMisc2 | read-write | current | A misc roaming value. |
| 1.3.6.1.4.1.232.145.1.5.1.22 | ScalarroamTableLength | read-only | current | This object specifies the maximum number of entries the roamTable can hold. |
| 1.3.6.1.4.1.232.145.1.5.1.23 | TableroamTable | not-accessible | current | The Roaming table contains all the BSSs the Client is aware of. An entry in the roamTable is only valid if the roamBSSID object of that entry contains a MAC ad… |
| 1.3.6.1.4.1.232.145.1.5.1.23.1 | RowroamEntry | not-accessible | current | An entry in the Roaming table. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.1 | ColumnroamIndex | not-accessible | current | The index into the table |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.2 | ColumnroamBSSID | read-only | current | The BSSID of the BSS. If this entry in the roamTable is not used, the roamBSSID is all zeros. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.3 | ColumnroamSSID | read-only | current | The Service Set ID the BSS is part of. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.4 | ColumnroamBSSType | read-only | current | The BSS Type of the entry. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.5 | ColumnroamChannel | read-only | current | The DS channel the BSS is using. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.6 | ColumnroamAge | read-only | current | An indicator (in seconds) for the age of the information on the BSS. The age is reset to 0 if a Beacon of this BSS is received. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.7 | ColumnroamQuality | read-only | current | An indicator for the quality of the BSS. The quality is calculated over the received Beacons of the BSS and depends on the selected quality indicator. The sema… |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.8 | ColumnroamLoad | read-only | current | An indicator for the load of the BSS. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.9 | ColumnroamBeaconPeriod | read-only | current | The beacon period (in time units) of this BSS. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.10 | ColumnroamDTIMPeriod | read-only | current | The DTIM period of this BSS. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.11 | ColumnroamCapabilityInfo | read-only | current | The Capability Information for this BSS. |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.12 | ColumnroamRates | read-only | current | The bit rates supported by the BSS. The least-significant 7 bits of each non-null octet value are a count from 00h -7Fh, corresponding to data rates in increme… |
| 1.3.6.1.4.1.232.145.1.5.1.23.1.13 | ColumnroamRSSI | read-only | current | An indicator for the RSSI of the BSS. The RSSI is calculated over the received Beacons of the BSS. |
| 1.3.6.1.5.1 | ScalarsecMACAclMaxTableLength | read-only | current | The maximum number of entries that the secMACAclTable can contain. |
| 1.3.6.1.5.2 | TablesecMACAclTable | not-accessible | current | The table containing an access control list (acl) with MAC addresses of 802.11 Clients and whether they are allowed to communicate with the wireless network th… |
| 1.3.6.1.5.2.1 | RowsecMACAclEntry | not-accessible | current | An entry in the table. |
| 1.3.6.1.5.2.1.1 | ColumnsecMACAclIndex | not-accessible | current | The index into the secMACAclTable. |
| 1.3.6.1.5.2.1.2 | ColumnsecMACAclAddress | read-create | current | The MAC address of a Client allowed to join the network through this Access Point. The address FF-FF-FF-FF-FF-FF constitutes the default behaviour for addresse… |
| 1.3.6.1.5.2.1.3 | ColumnsecMACAclAllowed | read-create | current | The flag indicating whether the corresponding MAC address is allowed to communicate through this Access Point or not. |
| 1.3.6.1.5.2.1.4 | ColumnsecMACAclRowStatus | read-create | current | The status value for creating and deleting rows in this table. |
| 1.3.6.1.5.3 | ScalarsecLastError | read-only | current | When a security violation or error occurs, the error code is written to this variable in the form of a string. |
| 1.3.6.1.5.4 | ScalarsecLastErrorAddress | read-only | current | When a security violation or error occurs, the MAC address involved in the violation or error is written to this variable. |