Wellfleet-BGP-MIB
194 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.3.2.5.1 | NodewfBgpGeneralGroup | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1 | NodewfBgp | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.1 | ScalarwfBgpDelete | read-write | mandatory | Create/Delete parameter for determining whether or not BGP is configured on this router. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.2 | ScalarwfBgpDisable | read-write | mandatory | Enable/Disable parameter for determining whether or not to allow any versions of BGP to start up. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.3 | ScalarwfBgpState | read-only | mandatory | the administrative state of BGP |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.4 | ScalarwfBgpIdentifier | read-write | mandatory | The BGP Identifier for this router. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.5 | ScalarwfBgpLocalAs | read-write | mandatory | The Autonomous System (AS) that this router belongs to. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.6 | ScalarwfBgpEbgpDebugSwitch | read-write | mandatory | If this debug switch is enabled, BGP will not enforce the rule that requires each EBGP peer to be on a directly attached network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.7 | ScalarwfBgpVersion | read-only | mandatory | Vector of supported BGP protocol version numbers. Each peer negotiates the version from this vector. Versions are identified via the string of bits contained w… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.8 | ScalarwfBgpIntraAsIbgpRouting | read-write | mandatory | If this switch is enabled, BGP will perform Intra-AS IBGP routing. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.9 | ScalarwfIbgpFromProtocols | read-write | mandatory | if Intra-AS IBGP routing is enabled, this attribute spcifies if non-BGP external routes can be propogated via IBGP. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.10 | ScalarwfBgpIntAdvTimer | read-write | mandatory | the minimum time interval, in seconds, between injections of EBGP routes into the IP routing table. default is 5. Can't be zero |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.11 | ScalarwfBgpUsedRoutes | read-only | mandatory | the number of received BGP routes that have been submitted for possible inclusion in the IP routing table. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.12 | ScalarwfBgpTotalRoutes | read-only | mandatory | the total number of BGP routes currently maintained. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.13 | ScalarwfBgpTotalPaths | read-only | mandatory | the total number of BGP path attributes blocks currently maintained. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.14 | ScalarwfBgpMaxRedundantIbgpRoutes | read-write | mandatory | Specifies the maximum number of IBGP routes to the same destination to be stored. At this point at least one route is stored even if zero is specified. If set … |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.15 | ScalarwfBgpRouteRequestSwitch | read-write | mandatory | If this switch is enabled and at least one connection to IBGP route server is enabled, alternate routes to a destination which became unreachable will be reque… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.16 | ScalarwfBgpConnCollisionDetect | read-write | mandatory | If this switch is enabled, redundant BGP connections to the same router will be detected and disallowed, i.e. only one BGP connection to the same router will b… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.17 | ScalarwfBgpRsTopology | read-write | mandatory | Specifies IBGP Route Server connection topology: none(Non-RS), RC, full-mesh, or tree. To enable Route Server mode full-mesh or tree topology must be selected. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.18 | ScalarwfBgpClusterIdentifier | read-write | mandatory | If RS Server, cluster Identifer for this server |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.19 | ScalarwfBgpDynamicPolChangeSupport | read-write | mandatory | If this switch is enabled, when a BGP policy rule changes all affected routes are dynamically re-evaluated according to the new policy specification. If this s… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.20 | ScalarwfBgpSoloistSlots | read-write | mandatory | Slot mask for which slots BGP is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.21 | ScalarwfBgpSoloistSlot | read-only | mandatory | Slot on which BGP runs in Soloist mode. Slots can be 1-14. Zero means that BGP is not in a Soloist mode. Default is zero. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.22 | ScalarwfBgpSubnetAggregation | read-write | mandatory | If this switch is enabled, non-BGP originated subnet routes are aggregated to their corresponding natural network routes for advertisement to bgp peers. Advert… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.23 | ScalarwfBgpBlackHoleSupport | read-write | mandatory | If this switch is disabled BGP doesn't submit a 'black-hole' route into IP routing table for an aggregate route advertised to a BGP peer. For action 'drop' pac… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.24 | ScalarwfBgpMedComparison | read-write | mandatory | If this switch is disabled BGP, the Multi-Exit Discriminator (MED) route attribute is not considered in the route selection process. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.25 | ScalarwfBgpIbgpReflection | read-write | mandatory | Enables/Disables reflecting of BGP routes to IBGP peers. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.26 | ScalarwfBgpIbgpEcmpMethod | read-write | mandatory | Method to use IGP ECMP routing information for an IBGP peering. route-balance method distributes a set of destination networks that share the same IBGP Next Ho… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.27 | ScalarwfBgpLocalPrefCalc | read-write | mandatory | Enable/disable local_pref calculation |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.28 | ScalarwfBgpConfedIdentifier | read-write | mandatory | The BGP Confederation Identifier for this router. NIL means this AS is not a member of any confederation |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.29 | ScalarwfBgpConfedPeers | read-write | mandatory | Peer list of this BGP speaker to other member sub_ASs within the same confederation, NIL means no peer from this speaker to neighbor ASs that are members of th… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.1.30 | ScalarwfBgpIgpInterAction | read-write | mandatory | Bit map for BGP/IGP interaction control: bit 15 bit 0 + | | + bit0: eBGP to OSPF bit1: eBGP to RIP bit2 - bit15: Reserved value 0 means no interaction |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2 | TablewfBgpPeerTable | not-accessible | mandatory | The BGP Peer table contains configuration and statistical information regarding this router's BGP peers |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1 | RowwfBgpPeerEntry | not-accessible | mandatory | An entry in the BGP-Peer table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.1 | ColumnwfBgpPeerDelete | read-write | mandatory | Create/Delete: if set to delete, the peer connection is removed |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.2 | ColumnwfBgpPeerDisable | read-write | mandatory | Enable/Disable: controls whether the peer connection is enabled or disabled |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.3 | ColumnwfBgpPeerState | read-only | mandatory | the administrative state of the peer connection on this interface |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.4 | ColumnwfBgpPeerLocalAddr | read-only | mandatory | the local interface address |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.5 | ColumnwfBgpPeerLocalPort | read-only | mandatory | the local TCP port number |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.6 | ColumnwfBgpPeerRemoteAddr | read-only | mandatory | the peer's interface address |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.7 | ColumnwfBgpPeerRemotePort | read-only | mandatory | the peer's TCP port number |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.8 | ColumnwfBgpPeerMinVersion | read-write | mandatory | the minimum BGP version number supported on this connection. Default is 4. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.9 | ColumnwfBgpPeerMaxVersion | read-write | mandatory | the maximum BGP version number supported on this connection Default is 4. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.10 | ColumnwfBgpPeerRemoteAs | read-write | mandatory | the configured peer's AS number. this must be filled in. the AS received in the open message must match this one. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.11 | ColumnwfBgpPeerExtAdvTimer | read-write | mandatory | Time interval in seconds for the MinRouteAdvertisementInterval BGP timer. Default is 30. Can't be zero |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.12 | ColumnwfBgpPeerConnectRetry | read-write | mandatory | the ConnectRetry timer, in seconds. this is the time between TCP connection attempts. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.13 | ColumnwfBgpPeerCfgHoldtime | read-write | mandatory | the configured Holdtime timer, in seconds. this is the maximum time that the peer can wait without receiving a KEEPALIVE from this speaker. if no hold timer is… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.14 | ColumnwfBgpPeerHoldtime | read-only | mandatory | the Holdtime timer value that was negotiated and is in use |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.15 | ColumnwfBgpPeerCfgKeepAlive | read-write | mandatory | the configured KeepAlive timer, in seconds. this is the interval between sending KEEPALIVE messages. if the hold timer was set to zero, this is ignored. otherw… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.16 | ColumnwfBgpPeerKeepAlive | read-only | mandatory | the value used for the KeepAlive timer |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.17 | ColumnwfBgpPeerPathAttrSwitch | read-write | obsolete | controls whether the wfBgp3PathAttrTable (and the bgpRcvdPathAttrTable) will be maintained. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.18 | ColumnwfBgpPeerIdentifier | read-only | mandatory | the BGP ID of the Peer |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.19 | ColumnwfBgpPeerConnState | read-only | mandatory | the state of the BGP connection FSM |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.20 | ColumnwfBgpPeerNegotiatedVersion | read-only | mandatory | the negotiated version of BGP running between the two peers |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.21 | ColumnwfBgpPeerInUpdates | read-only | mandatory | the number of BGP UPDATE messages received on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.22 | ColumnwfBgpPeerOutUpdates | read-only | mandatory | the number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.23 | ColumnwfBgpPeerInTotalMessages | read-only | mandatory | the total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.24 | ColumnwfBgpPeerOutTotalMessages | read-only | mandatory | the total number of messages transmitted from the remote peer on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.25 | ColumnwfBgpPeerLastError | read-only | mandatory | the last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte … |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.26 | ColumnwfBgpPeerTotalRoutes | read-only | mandatory | the total number of routes that were received from this peer that we are currently maintaining. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.27 | ColumnwfBgpPeerFsmEstablishedTransitions | read-only | mandatory | The total number of times the BGP FSM transitioned into the established state. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.28 | ColumnwfBgpPeerFsmEstablishedTime | read-only | mandatory | This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.29 | ColumnwfBgpPeerInUpdateElapsedTime | read-only | mandatory | Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time wfBgpPeerInUpdates is incremented, the value of this object is … |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.30 | ColumnwfBgpPeerMinASOriginationInterval | read-write | mandatory | Time interval in seconds for the MinASOriginationInterval timer. The default value for this timer is 15 seconds. Can't be zero. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.31 | ColumnwfBgpPeerLocalAS | read-write | mandatory | If configured, specifies the AS Number that is sent in OPEN message to this peer. If zero, the AS Number specified with wfBgpLocalAS attribute is used. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.32 | ColumnwfBgpPeerMaxUpdateSize | read-write | mandatory | Specifies the maximum size (in bytes) of UPDATE message that can be sent to this peer. Note that, if the message size that is needed to advertise a single rout… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.33 | ColumnwfBgpPeerRouteEchoSwitch | read-write | mandatory | The switch controls route echoing. If enabled, a BGP route that is selected for forwarding is advertised back to the peer from which the route was received. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.34 | ColumnwfBgpPeerDiscardDuplicateRouteSwitch | read-write | mandatory | Indicates if duplicate routes with the identical path attributes should be discarded. Should be enabled only when peering with an IBGP Route Server. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.35 | ColumnwfBgpPeerRSMode | read-write | mandatory | Indicates the Route Reflector / Route Server Mode of BGP peer: (1) - not a Route Server or Route Reflector connection; (2) - peer is a Route Server client; (3)… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.36 | ColumnwfBgpPeerRSIdentifier | read-write | obsolete | if wfBgpPeerRSMode is BGP_PEER_RS_MODE_INTERNAL or BGP_PEER_RS_MODE_RS_EXTERNAL, specifies the RS Identifier that is send in IDENTIFICATION message. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.37 | ColumnwfBgpPeerCfgDelayGranularity | read-write | mandatory | the configured delay granularity in seconds. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.38 | ColumnwfBgpPeerDelayGranularity | read-only | mandatory | the delay granularity in use |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.39 | ColumnwfBgpPeerLastErrorSrc | read-only | mandatory | The source of the last error notification received/sent \ ( 1 = recv / 2 = sent ). A null is present if no errors \ have occured. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.40 | ColumnwfBgpPeerNexthopSelf | read-write | mandatory | Disable the use of third party advertisements |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.41 | ColumnwfBgpPeerASLoopDetect | read-write | mandatory | Designates whether the router will kill a peering \ session if a Loop is detected in the AS Path. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.42 | ColumnwfBgpPeerBgpEcmpMethod | read-write | mandatory | Defines a method to use IGP ECMP routing information. route-balance method distributes a set of destination networks that share the same BGP Next Hop among ava… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.43 | ColumnwfBgpPeerDampenedRoutes | read-only | mandatory | Number of routes from this peer that are suppressed due to flap dampening. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.44 | ColumnwfBgpPeerTTL | read-write | mandatory | Configurable Time-To-Live field to be used for this peer connection. Unless wfBgpEbgpDebugSwitch is set, a TTL of 1 is used for external BGP connections. A val… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.45 | ColumnwfBgpPeerTcpAuthentication | read-write | mandatory | Indicates if BGP TCP Authentication is enabled\ none(1) - no authentication\ md5(2) - MD5 authentication enabled |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.46 | ColumnwfBgpPeerTcpMd5KeyStorage | read-write | mandatory | Indicates how the wfBgpPeerTcpMd5Key is stored \ in the MIB and configuration file. \ clear-text(1) - the key is stored unencrypted \ encrypted(2) - the key is… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.47 | ColumnwfBgpPeerTcpMd5Key | read-write | mandatory | if nil, no key configured\ if not nil, BGP TCP MD5 authentication key stored in \ wfBgpPeerTcpMd5KeyStorage format |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3 | TablewfBgpAsWeightTable | not-accessible | mandatory | The BGP AS weight table contains weights for autonomous systems for use in best-route calculations |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1 | RowwfBgpAsWeightEntry | not-accessible | mandatory | An entry in the BGP AS weight table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.1 | ColumnwfBgpAsWeightDelete | read-write | mandatory | Create/Delete: if set to delete, the AS entry is removed from this table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.2 | ColumnwfBgpAsWeightDisable | read-write | mandatory | Enable/Disable: controls whether the AS entry is enabled or disabled |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.3 | ColumnwfBgpAsWeightState | read-only | mandatory | the state of this AS weight entry |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.4 | ColumnwfBgpAsWeightNumber | read-only | mandatory | the AS number |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.5 | ColumnwfBgpAsWeightValue | read-write | mandatory | the class-1 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.6 | ColumnwfBgpAsWeightValue2 | read-write | mandatory | the class-2 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.7 | ColumnwfBgpAsWeightValue3 | read-write | mandatory | the class-3 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.8 | ColumnwfBgpAsWeightValue4 | read-write | mandatory | the class-4 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.9 | ColumnwfBgpAsWeightValue5 | read-write | mandatory | the class-5 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.10 | ColumnwfBgpAsWeightValue6 | read-write | mandatory | the class-6 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.11 | ColumnwfBgpAsWeightValue7 | read-write | mandatory | the class-7 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.12 | ColumnwfBgpAsWeightValue8 | read-write | mandatory | the class-8 value to assign to this AS |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4 | TablewfBgpPathAttrTable | not-accessible | obsolete | The BGP received path attribute table contains information about paths to destination networks received by all peers. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1 | RowwfBgpPathAttrEntry | not-accessible | obsolete | An entry in the BGP Path Attribute Table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.1 | ColumnwfBgpPathAttrIpAddrPrefix | read-only | obsolete | the IP address of the destination (sub)network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.2 | ColumnwfBgpPathAttrIpAddrPrefixLen | read-only | obsolete | Length in bits of the IP address prefix in the destination (sub)network address. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.3 | ColumnwfBgpPathAttrPeer | read-only | obsolete | the IP address of the peer where the path information was learned. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.4 | ColumnwfBgpPathAttrOrigin | read-only | obsolete | |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.5 | ColumnwfBgpPathAttrASPathSegment | read-only | obsolete | The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible val… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.6 | ColumnwfBgpPathAttrNextHop | read-only | obsolete | the address of the border router that should be used as the next-hop for the destination network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.7 | ColumnwfBgpPathAttrMultiExitDisc | read-only | obsolete | The optional inter-AS metric. If this attribute has not been provided for this route, the value for this object is -1. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.8 | ColumnwfBgpPathAttrLocalPref | read-only | obsolete | the originating BGP speaker's degree of preference for advertised route (-1..2147483647); if this attribute has not been provided for this route, the value for… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.9 | ColumnwfBgpPathAttrAtomicAggregate | read-only | obsolete | indicates whether or not the local system has selected a less specific route without selecting a more specific route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.10 | ColumnwfBgpPathAttrAggregatorAS | read-only | obsolete | The AS number of the last BGP speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.11 | ColumnwfBgpPathAttrAggregatorAddr | read-only | obsolete | The BGP ID of the last BGP speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.12 | ColumnwfBgpPathAttrCalcLocalPref | read-only | obsolete | The degree of preference calculated by the receiving BGP speaker for an advertised route (-1..2147483647). A value of -1 indicates the absence of this attribute |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.13 | ColumnwfBgpPathAttrBest | read-only | obsolete | an indication of whether or not this was chosen as the best bgp rout to the destination and whether or not it was chosen as a forwarding IP route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.14 | ColumnwfBgpPathAttrUnknown | read-only | obsolete | One or more path attributes not understood by this BGP speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size (255),… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.15 | ColumnwfBgpPathAttrImporterID | read-only | obsolete | For RS, the BGP ID of the border router that imported this route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.16 | ColumnwfBgpPathAttrClusterID | read-only | obsolete | For RS, the sequence of Cluter IDs of the Clusters. Size zero (0) indicates the absence of such attribute(s). |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.17 | ColumnwfBgpPathAttrCommunity | read-only | obsolete | List of BGP communities. Each community is 4 bytes long. Size zero (0) indicates the absence of community attribute. Octets beyond the maximum size (255), if a… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.18 | ColumnwfBgpPathAttrCalcMED | read-only | obsolete | The Multi Exit Disc. calculated by the receiving BGP speaker for an advertised route (-1...2G) |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5 | TablewfBgpDbgTable | not-accessible | mandatory | BGP debug table contains objects that controls generation of BGP debug information |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1 | RowwfBgpDbgEntry | not-accessible | mandatory | a table entry |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.1 | ColumnwfBgpDbgCreate | read-write | mandatory | Create/Delete parameter. Default is created. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.2 | ColumnwfBgpDbgLocAddr | read-only | mandatory | The peer's local address. If 0.0.0.0, debug attributes are applied to all peers to specified Remote Address or with specified BGP version |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.3 | ColumnwfBgpDbgRemoteAddr | read-write | mandatory | The peer's Remote Address . If 0.0.0.0, debug attrubutes are applied to all configured peers from specified Local Address; if 255.255.255.255, debug attrubutes… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.4 | ColumnwfBgpDbgMsgLevel | read-write | mandatory | BGP log messages level. To control certain level of log messages BGP_DBG_MSG_ALL 0x001f0000 - 2031616 BGP_DBG_MSG_DEBUG 0x00010000 - 65536 BGP_DBG_MSG_INFO 0x0… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.5 | ColumnwfBgpDbgMsgTraceSwitch | read-write | mandatory | controls whether BGP messages that are exchanged on this connection are dumped to the log. BGP_DBG_MSG_DUMP_REC_OPEN enables tracing of OPEN messages BGP_DBG_M… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.6 | ColumnwfBgpDbgLogCode | read-write | mandatory | Indicates that a debug log message which corresponds to the value of this attributes should be or should be not sent to the log. Affects wfBgpDbgCodes only. In… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.7 | ColumnwfBgpDbgLogCodeDisable | read-write | mandatory | Indicates that a debug log message defined in wfBgpDbgCode will be or will be not logged |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.8 | ColumnwfBgpDbgCodes | read-only | mandatory | Vector of enabled debug messages (to check only). Messages are identified via the string of bits contained within this attribute. The first octet contains bits… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.9 | ColumnwfBgpDbgBootCodes | read-write | mandatory | User-defined vector of enabled debug messages at boot moment. Coded as instance above |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6 | TablewfBgpVirtualPeerTable | not-accessible | mandatory | The BGP Virtual Peer table contains configuration and statistical information regarding this router's Virtual peers learned via the Route Server |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1 | RowwfBgpVirtualPeerEntry | not-accessible | mandatory | An entry in the BGP-Virtual-Peer table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.1 | ColumnwfBgpVirtualPeerLocalAddr | read-only | mandatory | the local interface address |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.2 | ColumnwfBgpVirtualPeerRemoteAddr | read-only | mandatory | the peer's interface address |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.3 | ColumnwfBgpVirtualPeerIdentifier | read-only | mandatory | the BGP ID of the Peer |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.4 | ColumnwfBgpVirtualPeerInUpdates | read-only | mandatory | the number of BGP UPDATE messages received on this connection. This object should be initialized to zero when the connection is established. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.5 | ColumnwfBgpVirtualPeerTotalRoutes | read-only | mandatory | the total number of routes that were received from this peer that we are currently maintaining. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.6 | ColumnwfBgpVirtualPeerInUpdateElapsedTime | read-only | mandatory | Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time wfBgpVirtualPeerInUpdates is incremented, the value of this obj… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7 | TablewfBgpPathAttributeTable | not-accessible | mandatory | The BGP received path attribute table contains information about paths to destination networks received by all peers. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1 | RowwfBgpPathAttributeEntry | not-accessible | mandatory | An entry in the BGP Path Attribute Table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.1 | ColumnwfBgpPathAttributeIpAddrPrefix | read-only | mandatory | the IP address of the destination (sub)network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.2 | ColumnwfBgpPathAttributeIpAddrPrefixLen | read-only | mandatory | Length in bits of the IP address prefix in the destination (sub)network address. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.3 | ColumnwfBgpPathAttributeImporterID | read-only | mandatory | For RS, the BGP ID of the border router that imported this route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.4 | ColumnwfBgpPathAttributePeer | read-only | mandatory | the IP address of the peer where the path information was learned. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.5 | ColumnwfBgpPathAttributeOrigin | read-only | mandatory | |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.6 | ColumnwfBgpPathAttributeASPathSegment | read-only | mandatory | The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible val… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.7 | ColumnwfBgpPathAttributeNextHop | read-only | mandatory | the address of the border router that should be used as the next-hop for the destination network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.8 | ColumnwfBgpPathAttributeMultiExitDisc | read-only | mandatory | The optional inter-AS metric. If this attribute has not been provided for this route, the value for this object is -1. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.9 | ColumnwfBgpPathAttributeLocalPref | read-only | mandatory | the originating BGP speaker's degree of preference for advertised route (-1..2147483647); if this attribute has not been provided for this route, the value for… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.10 | ColumnwfBgpPathAttributeAtomicAggregate | read-only | mandatory | indicates whether or not the local system has selected a less specific route without selecting a more specific route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.11 | ColumnwfBgpPathAttributeAggregatorAS | read-only | mandatory | The AS number of the last BGP speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.12 | ColumnwfBgpPathAttributeAggregatorAddr | read-only | mandatory | The BGP ID of the last BGP speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.13 | ColumnwfBgpPathAttributeCalcLocalPref | read-only | mandatory | The degree of preference calculated by the receiving BGP speaker for an advertised route (-1..2147483647). A value of -1 indicates the absence of this attribute |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.14 | ColumnwfBgpPathAttributeBest | read-only | mandatory | an indication of whether or not this was chosen as the best bgp rout to the destination and whether or not it was chosen as a forwarding IP route |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.15 | ColumnwfBgpPathAttributeUnknown | read-only | mandatory | One or more path attributes not understood by this BGP speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size (255),… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.16 | ColumnwfBgpPathAttributeClusterID | read-only | mandatory | For RS, the sequence of Cluter IDs of the Clusters. Size zero (0) indicates the absence of such attribute(s). |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.17 | ColumnwfBgpPathAttributeCommunity | read-only | mandatory | List of BGP communities. Each community is 4 bytes long. Size zero (0) indicates the absence of community attribute. Octets beyond the maximum size (255), if a… |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.18 | ColumnwfBgpPathAttributeCalcMED | read-only | mandatory | The Multi Exit Disc. calculated by the receiving BGP speaker for an advertised route (-1...2G) |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.19 | ColumnwfBgpPathAttributeFlapPenalty | read-only | mandatory | Penalty value based on number of route flaps |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.20 | ColumnwfBgpPathAttributeFlapCount | read-only | mandatory | Number of times a route flapped since the last time the penaltywas reset to zero |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.21 | ColumnwfBgpPathAttributeRouteDampened | read-only | mandatory | Shows whether this route is currently suppressed from being announced |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8 | TablewfBgpRouteFlapDampeningTable | not-accessible | mandatory | Table of wfBgpRouteFlapDampeningEntry |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1 | RowwfBgpRouteFlapDampeningEntry | not-accessible | mandatory | An entry in the Route Flap Dampening table |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.1 | ColumnwfBgpRouteFlapDampeningDelete | read-write | mandatory | Create/Delete: if set to delete, the entry is removed |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.2 | ColumnwfBgpRouteFlapDampeningIndex | read-only | mandatory | Index number of this entry in wfBgpRouteFlapDampeningTable |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.3 | ColumnwfBgpRouteFlapDampeningName | read-write | mandatory | Name of this template |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.4 | ColumnwfBgpRouteFlapDampeningCutoffThreshold | read-write | mandatory | Value of penalty over which a route is suppressed. Expressed in number of withdrawals |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.5 | ColumnwfBgpRouteFlapDampeningReuseThreshold | read-write | mandatory | Value of penalty below which a route is unsuppressed. Expressed in number of withdrawals |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.6 | ColumnwfBgpRouteFlapDampeningReachableDecay | read-write | mandatory | Duration in minutes after which the penalty value is reduced to half when the route is reachable. Default is 5 minutes |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.7 | ColumnwfBgpRouteFlapDampeningUnreachableDecay | read-write | mandatory | Duration in minutes after which the penalty value is reduced to half when the route is unreachable. Default is 15 minutes. |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.8 | ColumnwfBgpRouteFlapDampeningMaxHoldDown | read-write | mandatory | Maximum time a route remains suppressed. Expressed in number seconds. Default is 45 minutes |
| 1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.9 | ColumnwfBgpRouteFlapDampeningMemoryLimit | read-write | mandatory | If the state of a route(reachable/unreachable) remains stable for this duration, the penalty is cleared and the route unsuppressed. Expressed in number of minu… |
| 1.3.6.1.4.1.18.3.5.3.2.5.2 | NodewfBgp3Group | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1 | NodewfBgp3 | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.1 | ScalarwfBgp3Delete | read-write | mandatory | Create/Delete parameter for determining whether or not BGP3 is configured on this router. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.2 | ScalarwfBgp3Disable | read-write | mandatory | Enable/Disable parameter for determining whether or not to start-up BGP3. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.3 | ScalarwfBgp3State | read-only | mandatory | the administrative state of BGP-3 |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.4 | ScalarwfBgp3IntraAsIbgpRouting | read-write | obsolete | If this switch is enabled, BGP-3 will perform Intra-AS IBGP routing. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.5 | ScalarwfBgp3IntAdvTimer | read-write | obsolete | the minimum time interval, in seconds, between injections of EBGP routes into the IP routing table. default is 5. can't be zero |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.6 | ScalarwfBgp3RipRules | read-write | obsolete | if enabled, IBGP routes that are also reachable via a RIP route will be consider 'reachable' and will be used. the use of this is highly discouraged. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.7 | ScalarwfBgp3UsedRoutes | read-only | obsolete | the number of received BGP-3 routes that have been submitted for possible inclusion in the IP routing table. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.1.8 | ScalarwfBgp3TotalRoutes | read-only | obsolete | the total number of BGP-3 routes currently maintained. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2 | TablewfBgp3PathAttrTable | not-accessible | obsolete | The BGP3 received path attribute table contains information about paths to destination networks received by all peers. This table is deprecated and replaced wi… |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1 | RowwfBgp3PathAttrEntry | not-accessible | obsolete | An entry in the BGP-3 Path Attribute Table |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.1 | ColumnwfBgp3PathAttrPeer | read-only | obsolete | the BGP identifier of the peer where the path information was learned. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.2 | ColumnwfBgp3PathAttrDestNetwork | read-only | obsolete | the address of the destination network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.3 | ColumnwfBgp3PathAttrOrigin | read-only | obsolete | |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.4 | ColumnwfBgp3PathAttrASPath | read-only | obsolete | the set of ASes that must be traversed to reach the network. Each AS is represented as a pair of octets according to the following algorithm: first-byte-of-pai… |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.5 | ColumnwfBgp3PathAttrNextHop | read-only | obsolete | the address of the border router that should be used as the next-hop for the destination network. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.6 | ColumnwfBgp3PathAttrInterASMetric | read-only | obsolete | the optional inter-AS metric. if this attribute has not been provided for this route, the value for this object is 0. |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.7 | ColumnwfBgp3PathAttrASPathWeight | read-only | obsolete | the calculated AS path weight |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.8 | ColumnwfBgp3PathAttrBgpPreference | read-only | obsolete | the preference that is used to calculate this route with other BGP routes to the same destination |
| 1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.9 | ColumnwfBgp3PathAttrBest | read-only | obsolete | an indication of whether or not this was chosen as the best route to the destination |
| 1.3.6.1.4.1.18.3.5.3.2.5.3 | NodewfBgp4Group | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.3.1 | NodewfBgp4 | |||
| 1.3.6.1.4.1.18.3.5.3.2.5.3.1.1 | ScalarwfBgp4Delete | read-write | mandatory | Create/Delete parameter for determining whether or not BGP-4 is configured on this router. |
| 1.3.6.1.4.1.18.3.5.3.2.5.3.1.2 | ScalarwfBgp4Disable | read-write | mandatory | Enable/Disable parameter for determining whether or not to start-up BGP-4. |
| 1.3.6.1.4.1.18.3.5.3.2.5.3.1.3 | ScalarwfBgp4State | read-only | mandatory | the administrative state of BGP-4 |