Wellfleet-DS3E3-MIB
34 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.26.10 | TablewfDs3E3ConfigTable | not-accessible | mandatory | The DS3/E3 Configuration table |
| 1.3.6.1.4.1.18.3.4.26.10.1 | RowwfDs3E3ConfigEntry | not-accessible | mandatory | per circuit DS3/E3 configuration objects; wfDs3E3ConfigLineIndex corresponds to Wellfleet circuit number |
| 1.3.6.1.4.1.18.3.4.26.10.1.1 | ColumnwfDs3E3ConfigDelete | read-write | mandatory | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.26.10.1.2 | ColumnwfDs3E3ConfigDisable | read-write | mandatory | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.26.10.1.3 | ColumnwfDs3E3ConfigState | read-only | mandatory | State of the DS3 Port. |
| 1.3.6.1.4.1.18.3.4.26.10.1.4 | ColumnwfDs3E3ConfigLastChange | read-only | mandatory | The value of sysUpTime at the time the interface entered its current operational state. |
| 1.3.6.1.4.1.18.3.4.26.10.1.5 | ColumnwfDs3E3ConfigLineIndex | read-only | mandatory | this corresponds to the Wellfleet circuit number |
| 1.3.6.1.4.1.18.3.4.26.10.1.6 | ColumnwfDs3E3ConfigIfIndex | read-only | mandatory | this is value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.18.3.4.26.10.1.7 | ColumnwfDs3E3ConfigLineType | read-write | mandatory | the variety of DS3/E3 application implementing this circuit |
| 1.3.6.1.4.1.18.3.4.26.10.1.8 | ColumnwfDs3E3ConfigLineCoding | read-write | mandatory | the variety of Zero Code Suppression used on the link |
| 1.3.6.1.4.1.18.3.4.26.10.1.9 | ColumnwfDs3E3ConfigLoopbackConfig | read-write | mandatory | the loopback configuration of the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.10 | ColumnwfDs3E3ConfigLineStatus | read-only | mandatory | the status of the DS3/E3 line |
| 1.3.6.1.4.1.18.3.4.26.10.1.11 | ColumnwfDs3E3ConfigPrimaryClockSource | read-write | mandatory | Selects the Primary source of the Tx Clock for the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.12 | ColumnwfDs3E3ConfigSecondaryClockSource | read-write | mandatory | Selects the Secondary source of the Tx Clock for the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.13 | ColumnwfDs3E3ConfigMtu | read-write | mandatory | MTU parameter for all channels on DS3 . |
| 1.3.6.1.4.1.18.3.4.26.10.1.14 | ColumnwfDs3E3ConfigLineBuildOut | read-write | mandatory | Set according to cable length, short (less than 225 feet) or long (greater than 225 feet). |
| 1.3.6.1.4.1.18.3.4.26.10.1.15 | ColumnwfDs3E3ConfigCurrentClock | read-only | mandatory | Indicates the clock source currently in use by the DS1 |
| 1.3.6.1.4.1.18.3.4.26.10.1.16 | ColumnwfDs3E3ConfigExtClockOperational | read-only | mandatory | Indicates whether the External clock is operational |
| 1.3.6.1.4.1.18.3.4.26.10.1.17 | ColumnwfDs3E3ConfigSetupAlarmThreshold | read-write | mandatory | Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the time specified by this parameter… |
| 1.3.6.1.4.1.18.3.4.26.10.1.18 | ColumnwfDs3E3ConfigClearAlarmThreshold | read-write | mandatory | Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for greater than the time specified … |
| 1.3.6.1.4.1.18.3.4.26.10.1.19 | ColumnwfDs3E3ConfigLoopbackState | read-only | mandatory | Indicates the current loopback state of this interface. The interface can be in one the following states: Line Loopback Payload Loopback no loopback Loopback m… |
| 1.3.6.1.4.1.18.3.4.26.10.1.20 | ColumnwfDs3E3ConfigSendCode | read-only | mandatory | This variable is currently read-only and it indicates what type of code has been sent across the DS3 interface by the device. The values mean: SENDNOCODE - sen… |
| 1.3.6.1.4.1.18.3.4.26.17 | TablewfDs3E3ActionTable | not-accessible | mandatory | DS3E3 configuration Action record - write only Configuration parameters |
| 1.3.6.1.4.1.18.3.4.26.17.1 | RowwfDs3E3ActionEntry | not-accessible | mandatory | An entry in the DS3E3 Config table |
| 1.3.6.1.4.1.18.3.4.26.17.1.1 | ColumnwfDs3E3ActionPortLineNumber | read-only | mandatory | Instance ID LineNumber, filled in by driver |
| 1.3.6.1.4.1.18.3.4.26.17.1.2 | ColumnwfDs3E3ActionSendFeacLoopCode | read-write | mandatory | Selects a Far End Alarm and Control Channel code to be sent to the remote end. |
| 1.3.6.1.4.1.18.3.4.26.17.1.3 | ColumnwfDs3E3ActionSendFeacDs1LoopUpCode | read-write | mandatory | Selects Loop Up code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28). |
| 1.3.6.1.4.1.18.3.4.26.17.1.4 | ColumnwfDs3E3ActionSendFeacDs1LoopDownCode | read-write | mandatory | Selects Loop Down code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28). |
| 1.3.6.1.4.1.18.3.4.26.17.1.5 | ColumnwfDs3E3ActionClearCurrentStats | read-write | mandatory | Clears this port's Current 15 minute Statistics. |
| 1.3.6.1.4.1.18.3.4.26.17.1.6 | ColumnwfDs3E3ActionClearFarEndCurrentStats | read-write | mandatory | Clears this port's Far End, Current 15 minute Statistics. |
| 1.3.6.1.4.1.18.3.4.26.17.1.7 | ColumnwfDs3E3ActionClearDayCurrentStats | read-write | mandatory | Clears this port's Current Day Statistics. |
| 1.3.6.1.4.1.18.3.4.26.17.1.8 | ColumnwfDs3E3ActionClearFarEndDayCurrentStats | read-write | mandatory | Clears this port's Far End, Current Day Statistics. |
| 1.3.6.1.4.1.18.3.4.26.17.1.9 | ColumnwfDs3E3ActionClearIntervalStats | read-write | mandatory | Clears All Interval Statistics (15 minute and day) of this port. |
| 1.3.6.1.4.1.18.3.4.26.17.1.10 | ColumnwfDs3E3ActionClearFarEndIntervalStats | read-write | mandatory | Clears All Far End Interval Statistics (15 minute and day) of this port. |