Wellfleet-DSUCSU-MIB
25 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.30.1 | TablewfDsuCsuIfTable | not-accessible | mandatory | DSU CSU line record. |
| 1.3.6.1.4.1.18.3.4.30.1 | NodewfDsuCsuIfTrap | Indicates a change in the status of the line. The value returned in the trap will indicate the current state as defined in wfDsuCsuServiceStatus. | ||
| 1.3.6.1.4.1.18.3.4.30.1.1 | RowwfDsuCsuIfEntry | not-accessible | mandatory | An entry in the DSU CSU IF table |
| 1.3.6.1.4.1.18.3.4.30.1.1.1 | ColumnwfDsuCsuIfDelete | read-write | mandatory | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.30.1.1.2 | ColumnwfDsuCsuIfSlot | read-only | mandatory | Instance ID Slot, filled in by driver |
| 1.3.6.1.4.1.18.3.4.30.1.1.3 | ColumnwfDsuCsuIfConnector | read-only | mandatory | Instance ID Connector, filled in by the driver. |
| 1.3.6.1.4.1.18.3.4.30.1.1.4 | ColumnwfDsuCsuSoftRev | read-only | mandatory | Displays the Software Revision of the DSU CSU card. |
| 1.3.6.1.4.1.18.3.4.30.1.1.5 | ColumnwfDsuCsuHardRev | read-only | mandatory | Displays the Hardware Revision of the DSU CSU card. |
| 1.3.6.1.4.1.18.3.4.30.1.1.6 | ColumnwfDsuCsuOpMode | read-write | mandatory | Identifies the type of telco service that the DSU CSU is connected to. Opmode should be set to dds1-56kbps (1) when connected to a DDS1 56 Kbps line. Opmode sh… |
| 1.3.6.1.4.1.18.3.4.30.1.1.7 | ColumnwfDsuCsuTxClkSelect | read-write | mandatory | Default timing, or clock, source for transmiting data to the network. There must be only one source on a DDS line. Timing should always be slave (1) when conne… |
| 1.3.6.1.4.1.18.3.4.30.1.1.8 | ColumnwfDsuCsuUnitReset | read-write | mandatory | Enables the operator to remotely reset the unit. Using this command will cause the unit to terminate all its connections and drop data. |
| 1.3.6.1.4.1.18.3.4.30.1.1.9 | ColumnwfDsuCsu64KTxMonitor | read-write | mandatory | This signal is used in 64K Clear Channel mode to suppress customer data in the event that the data duplicates a network control code. A setting of enabled(1) s… |
| 1.3.6.1.4.1.18.3.4.30.1.1.10 | ColumnwfDsuCsuOpState | read-only | mandatory | Indicates the current operating state of the DSU CSU card. |
| 1.3.6.1.4.1.18.3.4.30.1.1.11 | ColumnwfDsuCsuServiceStatus | read-only | mandatory | The Current status of the physical interface. Your network carrier can send Out-of-Service or Maintenance Mode codes. |
| 1.3.6.1.4.1.18.3.4.30.1.1.12 | ColumnwfDsuCsuV54Lpbk | read-write | mandatory | Enables the operator to control, and examine the state of, V.54 loopbacks within the DSU CSU. |
| 1.3.6.1.4.1.18.3.4.30.1.1.13 | ColumnwfDsuCsuV54Timer | read-write | mandatory | Duration in seconds that a test specified in wfDsuCsuTestLpbk is to execute. |
| 1.3.6.1.4.1.18.3.4.30.1.1.14 | ColumnwfDsuCsuV54Errors | read-only | mandatory | Indicates the number of errors reported during the last loopback test. This count will only be updated for loopbacks with test pattern. |
| 1.3.6.1.4.1.18.3.4.30.1.1.15 | ColumnwfDsuCsuCqmsLaWindow | read-write | mandatory | Indicates the number of minutes within the window in which the availability of the line (network) is to be calculated. The availability of the line is an indic… |
| 1.3.6.1.4.1.18.3.4.30.1.1.16 | ColumnwfDsuCsuCqmsLaErrors | read-only | mandatory | Indicates the total number of seconds that the line was not in service in the last window of size wfDsuCsuCqmsLaWindow. |
| 1.3.6.1.4.1.18.3.4.30.1.1.17 | ColumnwfDsuCsuCqmsLaPollRate | read-write | mandatory | Indicates the number of seconds between polls for line status from the DsuCsu. A value of 1 forces polling every second. A value of 60 forces polling every min… |
| 1.3.6.1.4.1.18.3.4.30.1.1.18 | ColumnwfDsuCsuCqmsReset | read-write | mandatory | Resets the CQMS counters to their default values. For Line Availability, wfDsuCsuCqmsLaErrCnt is reset. |
| 1.3.6.1.4.1.18.3.4.30.1.1.19 | ColumnwfDsuCsuOOSErrors | read-only | mandatory | The number of seconds in which Out of Service control codes were received from the Telco. The counter is incremented whenever a sample within a second indicate… |
| 1.3.6.1.4.1.18.3.4.30.1.1.20 | ColumnwfDsuCsuFrameErrors | read-only | mandatory | The number of seconds in which the unit was out of frame with the Telco. This is only applicable in 64K mode. The counter is incremented whenever a sample with… |
| 1.3.6.1.4.1.18.3.4.30.1.1.21 | ColumnwfDsuCsuLOLErrors | read-only | mandatory | The number of seconds in which the unit has detected that no signal is present on the line, and/or no line is present. |
| 1.3.6.1.4.1.18.3.4.30.1.1.22 | ColumnwfDsuCsuInitState | read-only | mandatory | Indictes the state of the DSU/CSU initialization sequence. The state will indicate if the DSU/CSU has been initialized and is in the *monitor* state polling th… |