Wellfleet-FDDI-MIB
294 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.4 | TablewfFddiTable | not-accessible | mandatory | FDDI line record |
| 1.3.6.1.4.1.18.3.4.4.1 | RowwfFddiEntry | not-accessible | mandatory | An entry in the FDDI table |
| 1.3.6.1.4.1.18.3.4.4.1.1 | ColumnwfFDDIDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.4.1.2 | ColumnwfFDDIEnable | read-write | mandatory | Enable/disable parameter, default = enable. |
| 1.3.6.1.4.1.18.3.4.4.1.3 | ColumnwfFDDIState | read-only | mandatory | Line driver state variable, not present, init, down, up. |
| 1.3.6.1.4.1.18.3.4.4.1.4 | ColumnwfFDDISlot | read-only | mandatory | Instance ID slot - filled in by driver. |
| 1.3.6.1.4.1.18.3.4.4.1.5 | ColumnwfFDDINode | read-only | mandatory | Instance ID node - filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'node'. Where 'module' is defined in attri… |
| 1.3.6.1.4.1.18.3.4.4.1.6 | ColumnwfFDDICct | read-write | mandatory | Cct number for this line instance. |
| 1.3.6.1.4.1.18.3.4.4.1.7 | ColumnwfFDDIBofl | read-write | mandatory | The Breath-Of-Life (BOFL) function, when enabled, will disable the LLC interface when the FDDI becomes non-operational (i.e., link unavailable) and the followi… |
| 1.3.6.1.4.1.18.3.4.4.1.8 | ColumnwfFDDIBoflTmo | read-write | mandatory | Specifies the time value (in seconds) of the BOFL timer. The BOFL timer will be set to the value of this attribute when the following conditions are true: 1. T… |
| 1.3.6.1.4.1.18.3.4.4.1.9 | ColumnwfFDDIMtu | read-only | mandatory | The MTU is the maximum allowed frame length on the wire, excluding frame delimiters (i.e. preamble, ending delimiter). The MTU of an FDDI frame includes: FC (1… |
| 1.3.6.1.4.1.18.3.4.4.1.10 | ColumnwfFDDIMadr | read-only | mandatory | PROM-based MAC address, fixed - line driver fills in. |
| 1.3.6.1.4.1.18.3.4.4.1.11 | ColumnwfFDDIOctetsRxOk | read-only | mandatory | Number of bytes received without error. This byte count only includes LLC frames (i.e. no MAC and SMT frames). |
| 1.3.6.1.4.1.18.3.4.4.1.12 | ColumnwfFDDIFramesRxOk | read-only | mandatory | Number of frames received without error. This frame count only includes LLC frames (i.e. no MAC and SMT frames). |
| 1.3.6.1.4.1.18.3.4.4.1.13 | ColumnwfFDDIOctetsTxOk | read-only | mandatory | Number of bytes transmitted without error. This byte count only includes LLC and SMT frames (i.e. no MAC frames). |
| 1.3.6.1.4.1.18.3.4.4.1.14 | ColumnwfFDDIFramesTxOk | read-only | mandatory | Number of frames transmitted without error. This frame count only includes LLC and SMT frames (i.e. no MAC frames ). |
| 1.3.6.1.4.1.18.3.4.4.1.15 | ColumnwfFDDICrcErrRx | read-only | mandatory | Number of frames received with CRC errors. |
| 1.3.6.1.4.1.18.3.4.4.1.16 | ColumnwfFDDIOverrunRx | read-only | mandatory | Number of frames received with internal overrun errors. |
| 1.3.6.1.4.1.18.3.4.4.1.17 | ColumnwfFDDIParityErrRx | read-only | mandatory | Number of frames received with parity errors. |
| 1.3.6.1.4.1.18.3.4.4.1.18 | ColumnwfFDDIMacErrRx | read-only | mandatory | Number of frames received with MAC errors. |
| 1.3.6.1.4.1.18.3.4.4.1.19 | ColumnwfFDDIRingErrRx | read-only | mandatory | Number of receive ring error events. |
| 1.3.6.1.4.1.18.3.4.4.1.20 | ColumnwfFDDISmtRingErrRx | read-only | mandatory | Number of SMT receive ring error events. |
| 1.3.6.1.4.1.18.3.4.4.1.21 | ColumnwfFDDIRingOverrunRx | read-only | mandatory | Number of LLC receive ring overrun events. |
| 1.3.6.1.4.1.18.3.4.4.1.22 | ColumnwfFDDISmtRingOverrunRx | read-only | mandatory | Number of SMT receive ring overrun events. |
| 1.3.6.1.4.1.18.3.4.4.1.23 | ColumnwfFDDIAbortTx | read-only | mandatory | Number of transmit frames with internal abort errors. |
| 1.3.6.1.4.1.18.3.4.4.1.24 | ColumnwfFDDIUnderrunTx | read-only | mandatory | Number of transmit frames aborted with underrun errors. |
| 1.3.6.1.4.1.18.3.4.4.1.25 | ColumnwfFDDIParityErrTx | read-only | mandatory | Number of transmit frames aborted with parity errors. |
| 1.3.6.1.4.1.18.3.4.4.1.26 | ColumnwfFDDIRingErrTx | read-only | mandatory | Number of LLC/SMT transmit ring error events. |
| 1.3.6.1.4.1.18.3.4.4.1.27 | ColumnwfFDDIPortOpErr | read-only | mandatory | Number of port operation error events. |
| 1.3.6.1.4.1.18.3.4.4.1.28 | ColumnwfFDDIInternOpErr | read-only | mandatory | Number of internal operation error events. |
| 1.3.6.1.4.1.18.3.4.4.1.29 | ColumnwfFDDIHostErr | read-only | mandatory | Number of host error events. |
| 1.3.6.1.4.1.18.3.4.4.1.30 | ColumnwfFDDISmtConnectionPolicy | read-write | mandatory | A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it reject… |
| 1.3.6.1.4.1.18.3.4.4.1.31 | ColumnwfFDDISmtTNotify | read-write | mandatory | The timer used in the Neighbor Notification protocol, reported in seconds and ranging from 2 to 30 seconds. |
| 1.3.6.1.4.1.18.3.4.4.1.32 | ColumnwfFDDIMacTReq | read-write | mandatory | Specifies the maximum time value of 'wfFddiPathMaxTReq' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiPathMaxT… |
| 1.3.6.1.4.1.18.3.4.4.1.33 | ColumnwfFDDIMacTMax | read-only | mandatory | The requested maximum TTRT to be supported by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| 1.3.6.1.4.1.18.3.4.4.1.34 | ColumnwfFDDIMacTvxValue | read-only | mandatory | The requested value of TvxValue represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| 1.3.6.1.4.1.18.3.4.4.1.35 | ColumnwfFDDIMacTMin | read-only | mandatory | The requested minimum TTRT to be requested by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). |
| 1.3.6.1.4.1.18.3.4.4.1.36 | ColumnwfFDDIHardwareFilter | read-write | mandatory | Hardware filter (CAM) parameter. |
| 1.3.6.1.4.1.18.3.4.4.1.37 | ColumnwfFDDISmtEnable | read-write | mandatory | Enable Station Management periodic timer and NIF protocol. |
| 1.3.6.1.4.1.18.3.4.4.1.38 | ColumnwfFDDITxQueueLength | read-only | mandatory | Current Transmit Queue Length |
| 1.3.6.1.4.1.18.3.4.4.1.39 | ColumnwfFDDIRxQueueLength | read-only | mandatory | Current Receive Queue Length |
| 1.3.6.1.4.1.18.3.4.4.1.40 | ColumnwfFDDITxClipFrames | read-only | mandatory | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| 1.3.6.1.4.1.18.3.4.4.1.41 | ColumnwfFDDIRxReplenMisses | read-only | mandatory | Number of packet buffer misses while attempting to replenish driver receive ring. |
| 1.3.6.1.4.1.18.3.4.4.1.42 | ColumnwfFDDICfgTxQueueLength | read-write | mandatory | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based … |
| 1.3.6.1.4.1.18.3.4.4.1.43 | ColumnwfFDDICfgRxQueueLength | read-write | mandatory | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero cuases router based d… |
| 1.3.6.1.4.1.18.3.4.4.1.44 | ColumnwfFDDILineNumber | read-write | mandatory | Logical line number associated with this driver entity. |
| 1.3.6.1.4.1.18.3.4.4.1.45 | ColumnwfFDDIForcePeerTree | read-write | mandatory | This attribute allows all FDDI Peer/Tree connections to reach the 'Thru' state. This is done to give the user some flexibility and allow them to Daisy Chain th… |
| 1.3.6.1.4.1.18.3.4.4.1.46 | ColumnwfFDDIInvalidFrameStatusRx | read-only | mandatory | A count of the number of badly formed frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 cont… |
| 1.3.6.1.4.1.18.3.4.4.1.47 | ColumnwfFDDIRxOversizedFrames | read-only | mandatory | Number of LLC frames received whose length exceeded the MTU. |
| 1.3.6.1.4.1.18.3.4.4.1.48 | ColumnwfFDDIRxSmtOversizedFrames | read-only | mandatory | Number of SMT frames received whose length exceeded the MTU. |
| 1.3.6.1.4.1.18.3.4.4.1.49 | ColumnwfFDDIRxUndersizedFrames | read-only | mandatory | Number of LLC frames received whose length was less than 20 bytes including the FC byte and a 4 byte CRC. |
| 1.3.6.1.4.1.18.3.4.4.1.50 | ColumnwfFDDIRxSmtUndersizedFrames | read-only | mandatory | Number of SMT frames received whose length was less than 37 bytes including the FC byte and a 4 byte CRC. |
| 1.3.6.1.4.1.18.3.4.4.1.51 | ColumnwfFDDIModule | read-only | mandatory | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.4.1.52 | ColumnwfFDDIActualNode | read-only | mandatory | Actual Node number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.4.1.53 | ColumnwfFDDILastChange | read-only | mandatory | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second… |
| 1.3.6.1.4.1.18.3.4.4.1.54 | ColumnwfFDDIOutQLen | read-only | mandatory | The instantaneous current length of the output packet queue (in packets). |
| 1.3.6.1.4.1.18.3.4.4.1.55 | ColumnwfFDDIRxSmtOctets | read-only | mandatory | Number of bytes received without error. This byte count only includes SMT frames (i.e. no MAC and LLC frames). |
| 1.3.6.1.4.1.18.3.4.4.1.56 | ColumnwfFDDIRxSmtFrames | read-only | mandatory | Number of frames received without error. This frame count only includes SMT frames (i.e. no MAC and LLC frames). |
| 1.3.6.1.4.1.18.3.4.4.1.57 | ColumnwfFDDIIntProcessings | read-only | mandatory | Counts the number of times the interrupt service routine has been called |
| 1.3.6.1.4.1.18.3.4.4.1.58 | ColumnwfFDDITxProcessings | read-only | mandatory | Counts the number of times the transmit routine fsi_xmt_oper_act(), has been called |
| 1.3.6.1.4.1.18.3.4.4.1.59 | ColumnwfFDDIRxProcessings | read-only | mandatory | Counts the number of times RINT processing takes place in the interrupt service routine. |
| 1.3.6.1.4.1.18.3.4.4.1.60 | ColumnwfFDDITxRNRProcessings | read-only | mandatory | Counts the number of times the transmit complete routine fsi_xmt_cmpl(), has been called |
| 1.3.6.1.4.1.18.3.4.4.1.61 | ColumnwfFDDISmtRxProcessings | read-only | mandatory | Counts the number of time RINT was processing was performed on the SMT receive ring. |
| 1.3.6.1.4.1.18.3.4.4.1.62 | ColumnwfFDDIPhyALogPtr | read-only | mandatory | Address of the Debug Phy Event Buffer for Phy A. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| 1.3.6.1.4.1.18.3.4.4.1.63 | ColumnwfFDDIPhyBLogPtr | read-only | mandatory | Address of the Debug Phy Event Buffer for Phy B. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| 1.3.6.1.4.1.18.3.4.4.1.64 | ColumnwfFDDIPromiscuous | read-write | mandatory | For now this attribute is used only in BNX code !!! The promiscuous parameter allows address filtering based on the destination MAC addresses. When enabled, al… |
| 1.3.6.1.4.1.18.3.4.4.1.65 | ColumnwfFDDILLCFrameControl | read-write | mandatory | Frame control used for LLC frames, using synchronous frames for reserved priority traffic when specified. |
| 1.3.6.1.4.1.18.3.4.4.1.66 | ColumnwfFDDITurboBofl | read-write | mandatory | DEBUG parameter - Turbo bofl enabled or disabled, by adjusting BoflNum and BoflLen bofl packets can be made to fill the links available bandwith. This function… |
| 1.3.6.1.4.1.18.3.4.4.1.67 | ColumnwfFDDIBoflNum | read-write | mandatory | DEBUG parameter - Number of breath of life packets per breath of life |
| 1.3.6.1.4.1.18.3.4.4.1.68 | ColumnwfFDDIBoflLen | read-write | mandatory | DEBUG parameter - breath of life packet length |
| 1.3.6.1.4.1.18.3.4.15.1 | NodewfFddiSmtGroup | |||
| 1.3.6.1.4.1.18.3.4.15.1.2 | TablewfFddiSmtTable | not-accessible | mandatory | A list of SMT entries. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1 | RowwfFddiSmtEntry | not-accessible | mandatory | A SMT entry containing information common to a given SMT. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.1 | ColumnwfFddiSmtSlot | read-only | mandatory | Slot number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.2 | ColumnwfFddiSmtNode | read-only | mandatory | Node/connector number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.3 | ColumnwfFddiSmtCct | read-only | mandatory | Circuit number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.4 | ColumnwfFddiSmtStationId | read-only | mandatory | Unique identifier of an FDDI station. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.5 | ColumnwfFddiSmtOpVersionId | read-only | mandatory | The version that this station is using for its operation. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.6 | ColumnwfFddiSmtMacCt | read-only | mandatory | The number of MACs in a station. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.7 | ColumnwfFddiSmtNonMasterCt | read-only | mandatory | The number of non master ports (A, B, or S PORTs) in a station. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.8 | ColumnwfFddiSmtEcmState | read-only | mandatory | Indicates the current state of the ECM state machine. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.9 | ColumnwfFddiSmtCfState | read-only | mandatory | The attachment configuration for a station. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.10 | ColumnwfFddiSmtBypassPresent | read-only | mandatory | A flag indicating if the station has an optical bypass on its A/B port pair. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.11 | ColumnwfFddiSmtRemoteDisconnectFlag | read-only | mandatory | A flag indicating that the station was remotely disconnected from the network as a result of receiving an 'wfFddiSmtStationAction' disconnect in a Parameter Ma… |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.12 | ColumnwfFddiSmtStationStatus | read-only | mandatory | This variable indicates the current state of the primary and secondary paths within this station. |
| 1.3.6.1.4.1.18.3.4.15.1.2.1.13 | ColumnwfFddiSmtPeerWrapFlag | read-only | mandatory | This variable assumes the value of the 'PeerWrapFlag' in CFM. |
| 1.3.6.1.4.1.18.3.4.15.1.3 | TablewfFddiSmtExtTable | not-accessible | mandatory | A list of SMT extension entries. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1 | RowwfFddiSmtExtEntry | not-accessible | mandatory | A SMT entry containing information common to a given SMT. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.1 | ColumnwfFddiSmtDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.2 | ColumnwfFddiSmtExtSlot | read-only | mandatory | Slot number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.3 | ColumnwfFddiSmtExtNode | read-only | mandatory | Node/connector number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.4 | ColumnwfFddiSmtExtCct | read-only | mandatory | Circuit number associated with an SMT entity. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.5 | ColumnwfFddiSmtHiVersionId | read-only | mandatory | The highest version of SMT that this station supports. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.6 | ColumnwfFddiSmtLoVersionId | read-only | mandatory | The lowest version of SMT that this station supports. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.7 | ColumnwfFddiSmtManufacturerData | read-only | mandatory | Contains 32 Octets of manufacturer data. The first component, manufacturing OUI, is the 3 octet Organizationally Unique Identifier (OUI) assigned by IEEE. The … |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.8 | ColumnwfFddiSmtUserData | read-write | mandatory | Contains 32 Octets of user defined information in ascii format. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.9 | ColumnwfFddiSmtMibVersionId | read-only | mandatory | The version of the FDDI MIB of this station. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.10 | ColumnwfFddiSmtMasterCts | read-only | mandatory | The number of M ports in a node. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.11 | ColumnwfFddiSmtAvailablePaths | read-only | mandatory | A bit string that indicates the path types that are available in the station. The value initially takes the value 0, then for each type of path that this node … |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.12 | ColumnwfFddiSmtConfigCapabilities | read-only | mandatory | A bit string which indicates the configuration capabilities of a node. The 'Hold Available' bit indicates the support of the optional Hold function, which is c… |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.13 | ColumnwfFddiSmtConfigPolicy | read-only | mandatory | A bit string representing the configuration policies currently desired in a node. 'Hold' is one of the terms used for the 'Hold' flag. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.14 | ColumnwfFddiSmtStatRptPolicy | read-write | mandatory | If ENABLED, indicates that the node will generate Status Report Frames (SRF) for its implemented events. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.15 | ColumnwfFddiSmtTraceMaxExpiration | read-write | mandatory | Maximum propogation time for a Trace on an FDDI topology. The value is stored in milliseconds. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.16 | ColumnwfFddiSmtTimeStamp | read-only | mandatory | Holds the time of creation of the last Status Report Frame (SRF). |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.17 | ColumnwfFddiSmtTransitionTimeStamp | read-only | mandatory | Holds the time of occurrence of the last condition or event. |
| 1.3.6.1.4.1.18.3.4.15.1.3.1.18 | ColumnwfFddiSmtDatProtocol | read-write | mandatory | SMT will implement an optional ANSI duplicate address test involving periodic transmission of NSA NIF frames addressed to itself if enabled by this attribute. |
| 1.3.6.1.4.1.18.3.4.15.1.4 | TablewfFddiSmtActionTable | not-accessible | mandatory | A list of SMT action entries. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1 | RowwfFddiSmtActionEntry | not-accessible | mandatory | An SMT entry containing actions common to a given SMT. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1.1 | ColumnwfFddiSmtActionDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1.2 | ColumnwfFddiSmtActionSlot | read-only | mandatory | Slot number associated with an SMT action entity. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1.3 | ColumnwfFddiSmtActionNode | read-only | mandatory | Node/connector number associated with an SMT action entity. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1.4 | ColumnwfFddiSmtActionCct | read-only | mandatory | Circuit number associated with an SMT action entity. |
| 1.3.6.1.4.1.18.3.4.15.1.4.1.5 | ColumnwfFddiSmtStationAction | read-write | mandatory | This object when read, always returns a value of other(1). The behavior of setting this variable to each of the acceptable values is as follows: Other: Results… |
| 1.3.6.1.4.1.18.3.4.15.2 | NodewfFddiMacGroup | |||
| 1.3.6.1.4.1.18.3.4.15.2.2 | TablewfFddiMacTable | not-accessible | mandatory | A list of MAC entries. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1 | RowwfFddiMacEntry | not-accessible | mandatory | A MAC entry containing information common to a given MAC. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.1 | ColumnwfFddiMacSlot | read-only | mandatory | Slot number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.2 | ColumnwfFddiMacNode | read-only | mandatory | Node/connector number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.3 | ColumnwfFddiMacCct | read-only | mandatory | Circuit number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.4 | ColumnwfFddiMacUpstreamNbr | read-only | mandatory | The MAC's upstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 … |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.5 | ColumnwfFddiMacDownstreamNbr | read-only | mandatory | The MAC's downstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '0… |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.6 | ColumnwfFddiMacSmtAddress | read-only | mandatory | The 48 bit individual address of the MAC used for SMT frames. SMT uses the MSB form for representation of 48-bit addresses. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.7 | ColumnwfFddiMacTNeg | read-only | mandatory | The negotiated TTRT during the claim process represented as an unsigned integer specifying time in nanoseconds. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.8 | ColumnwfFddiMacRmtState | read-only | mandatory | Indicates the current state of the Ring Management state machine. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.9 | ColumnwfFddiMacOldUpstreamNbr | read-only | mandatory | The previous value of the MAC's upstream neighbor's long individual MAC address. It has an initial value of the SMT-Unknown-MAC Address and is only modified as… |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.10 | ColumnwfFddiMacOldDownstreamNbr | read-only | mandatory | The previous value of the MAC's downstream neighbor's long individual MAC address. It has an initial value of the SMT-Unknown-MAC Address and is only modified … |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.11 | ColumnwfFddiMacTokenCts | read-only | mandatory | A count that should as closely as possible match the number of times the station has received a token (total of non-restricted and restricted) on this MAC. Thi… |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.12 | ColumnwfFddiMacErrorCts | read-only | mandatory | A count of the number of frames that were detected in error by this MAC that had not been detected in error by another MAC. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.13 | ColumnwfFddiMacLostCts | read-only | mandatory | A count of the number of instances that this MAC detected a format error during frame reception such that the frame was stripped. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.14 | ColumnwfFddiMacDaFlag | read-only | mandatory | Duplicate Address Flag. An RMT flag used to indicate that the MAC under control has the same address as another MAC on the FDDI. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.15 | ColumnwfFddiMacUnaDaFlag | read-only | mandatory | A flag, UNDA_Flag, set when the upstream neighbor reports a duplicate address condition. Cleared once the condition clears. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.16 | ColumnwfFddiMacFrameErrorFlag | read-only | mandatory | Indicates the MAC Frame Error Condition is present when set. Cleared when the condition clears and on station initialization. |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.17 | ColumnwfFddiMacMaUnitDataAvailable | read-only | mandatory | A flag indicating that the MAC is available for the transmission and reception of Protocol Data Units (PDUs). The MAC and LLC interface will be established whe… |
| 1.3.6.1.4.1.18.3.4.15.2.2.1.18 | ColumnwfFddiMacDownstreamPortType | read-only | mandatory | Indicates the PC-Type of the first port that is downstream of this MAC (the exit port). |
| 1.3.6.1.4.1.18.3.4.15.2.3 | TablewfFddiMacExtTable | not-accessible | mandatory | A list of MAC extension entries. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1 | RowwfFddiMacExtEntry | not-accessible | mandatory | A MAC entry containing information common to a given MAC. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.1 | ColumnwfFddiMacDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.2 | ColumnwfFddiMacExtSlot | read-only | mandatory | Slot number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.3 | ColumnwfFddiMacExtNode | read-only | mandatory | Node/connector number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.4 | ColumnwfFddiMacExtCct | read-only | mandatory | Circuit number associated with a MAC entity. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.5 | ColumnwfFddiMacFrameStatusFunctions | read-only | mandatory | Indicates the MAC's optional Frame Status processing functions. The value is a sum. This value initially takes the value 0, then for each function present, 2 r… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.6 | ColumnwfFddiMacBridgeFunctions | read-only | mandatory | |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.7 | ColumnwfFddiMacTMaxCapability | read-only | mandatory | Indicates the maximum time value (in nanoseconds) of 'wfFddiMacTMax' that this MAC can support. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.8 | ColumnwfFddiMacTvxCapability | read-only | mandatory | Indicates the maximum time value (in nanoseconds) of 'wfFddiMacTvxValue' that this MAC can support. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.9 | ColumnwfFddiMacAvailablePaths | read-only | mandatory | Indicates the paths available for this MAC. The value is a sum. This value initially takes the value 0, then for each type of PATH that this MAC has available,… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.10 | ColumnwfFddiMacCurrentPath | read-only | mandatory | Indicates the Path into which this MAC is currently inserted. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.11 | ColumnwfFddiMacDupAddrTest | read-only | mandatory | The Duplicate Address test flag. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.12 | ColumnwfFddiMacRequestedPaths | read-only | mandatory | Contains a list of Permitted Paths which specifies the Path(s) into which the MAC may be inserted. The value is a sum which represents the individual paths tha… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.13 | ColumnwfFddiMacCopiedCts | read-only | mandatory | A count that should as closely as possible match the number of frames addressed to (A bit set) and successfully copied into the station's receive buffers (C bi… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.14 | ColumnwfFddiMacFrameErrorThreshold | read-write | mandatory | Specifies the Mac Frame Error Threshold for determining when a MAC Frame Error Condition report will be generated (via an SRF Frame). If Mac Frame Error Ratio … |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.15 | ColumnwfFddiMacFrameErrorRatio | read-only | mandatory | This variable is the value of the ratio: ((delta wfFddiMacLostCts + delta wfFddiMacErrorCts) / (delta wfFddiMacFrameCts + delta wfFddiMacLostCts)) 2**16) |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.16 | ColumnwfFddiMacHardwarePresent | read-only | mandatory | This variable indicates the presence of underlying hardware support for this MAC object. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.17 | ColumnwfFddiMacMaUnitDataEnable | read-write | mandatory | A configurable attribute that specifies whether the MAC will be available for the transmission and reception of Protocol Data Units (PDUs). If enabled, the int… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.18 | ColumnwfFddiMacTvxExpiredCts | read-only | mandatory | A count that should as closely as possible match the number of times that TVX has expired. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.19 | ColumnwfFddiMacLateCts | read-only | mandatory | A count that should as closely as possible match the number of TRT expirations since this MAC was reset or a token was received. |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.20 | ColumnwfFddiMacRingOpCts | read-only | mandatory | The count of the number of times the ring has entered the 'Ring Operational' state from the `Ring Not Operational' state. This count is updated when a SM_MA_ST… |
| 1.3.6.1.4.1.18.3.4.15.2.3.1.21 | ColumnwfFddiMacDuplicateTokenCts | read-only | mandatory | The count of the number of times a Duplicate Token has been detected. |
| 1.3.6.1.4.1.18.3.4.15.3 | NodewfFddiPathGroup | |||
| 1.3.6.1.4.1.18.3.4.15.3.2 | TablewfFddiPathTable | not-accessible | mandatory | A list of PATH entries. |
| 1.3.6.1.4.1.18.3.4.15.3.2.1 | RowwfFddiPathEntry | not-accessible | mandatory | A PATH entry containing information common to a given PATH. |
| 1.3.6.1.4.1.18.3.4.15.3.2.1.1 | ColumnwfFddiPathSlot | read-only | mandatory | Slot number associated with a PATH entity. |
| 1.3.6.1.4.1.18.3.4.15.3.2.1.2 | ColumnwfFddiPathNode | read-only | mandatory | Node/connector number associated with a PATH entity. |
| 1.3.6.1.4.1.18.3.4.15.3.2.1.3 | ColumnwfFddiPathCct | read-only | mandatory | Circuit number associated with a PATH entity. |
| 1.3.6.1.4.1.18.3.4.15.3.2.1.4 | ColumnwfFddiPathConfiguration | read-only | mandatory | A circular list of resources on the path where each entry in the list consists of a resource type identifier (MAC or PORT), an index, and its CurrentPath. If t… |
| 1.3.6.1.4.1.18.3.4.15.3.3 | TablewfFddiPathExtTable | not-accessible | mandatory | A list of PATH extension entries. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1 | RowwfFddiPathExtEntry | not-accessible | mandatory | A PATH entry containing information common to a given PATH. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.1 | ColumnwfFddiPathDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.2 | ColumnwfFddiPathExtSlot | read-only | mandatory | Slot number associated with a Path entity. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.3 | ColumnwfFddiPathExtNode | read-only | mandatory | Node/connector number associated with a Path entity. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.4 | ColumnwfFddiPathExtCct | read-only | mandatory | Circuit number associated with a Path entity. |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.5 | ColumnwfFddiPathTvxLowerBound | read-write | mandatory | Specifies the minimum time value of 'wfFddiMacTvxValue' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiMacTvxVa… |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.6 | ColumnwfFddiPathTMaxLowerBound | read-write | mandatory | Specifies the minimum time value of 'wfFddiMACTMax' that shall be used by any MAC that is configured in this path. The operational value of 'wfFddiMacTMax' is … |
| 1.3.6.1.4.1.18.3.4.15.3.3.1.7 | ColumnwfFddiPathMaxTReq | read-only | mandatory | This variable is the T_Req_value passed to the MAC. Without having detected a duplicate, the time value of this variable shall assume the maximum supported tim… |
| 1.3.6.1.4.1.18.3.4.15.4 | NodewfFddiPortGroup | |||
| 1.3.6.1.4.1.18.3.4.15.4.2 | TablewfFddiPortTable | not-accessible | mandatory | A list of PORT entries. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1 | RowwfFddiPortEntry | not-accessible | mandatory | A PORT entry containing information common to a given PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.1 | ColumnwfFddiPortSlot | read-only | mandatory | Slot number associated with a PORT entity. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.2 | ColumnwfFddiPortNode | read-only | mandatory | Node/connector number associated with a PORT entity. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.3 | ColumnwfFddiPortCct | read-only | mandatory | Circuit number associated with a PORT entity. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.4 | ColumnwfFddiPortIndex | read-only | mandatory | A unique value for each PORT associated with each slot/connector pair. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.5 | ColumnwfFddiPortPcType | read-only | mandatory | The physical connector type of the local PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.6 | ColumnwfFddiPortPcNeighbor | read-only | mandatory | The physical connector type of the remote PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.7 | ColumnwfFddiPortPcmState | read-only | mandatory | State of Physical State Machine. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.8 | ColumnwfFddiPortRequestedPaths | read-only | mandatory | This variable is a list of permitted paths where each list element defines the Port's permitted paths. The first octet corresponds to 'none', the second octet … |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.9 | ColumnwfFddiPortBsFlag | read-only | mandatory | Break State Flag - A PCM flag used to indicate that the PCM state Machine is not leaving the Break State in an expected time interval & a problem is suspected. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.10 | ColumnwfFddiPortLerFlag | read-only | mandatory | The condition becomes active when the value of 'wfFddiPortLerEstimate' is <= 'wfFddiPortLerAlarm'. This will be reported with Status Report Frames (SRF). |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.11 | ColumnwfFddiPortConnectState | read-only | mandatory | A variable from PCM to other management entities indicating the state of the connection. |
| 1.3.6.1.4.1.18.3.4.15.4.2.1.12 | ColumnwfFddiPortMacIndicated | read-only | mandatory | The indications (T_Val(9), R_Val(9)) in PC-Signalling, of the intent to place a MAC in the output token path to a PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.3 | TablewfFddiPortExtTable | not-accessible | mandatory | A list of PORT extension entries. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1 | RowwfFddiPortExtEntry | not-accessible | mandatory | A PORT entry containing information common to a given PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.1 | ColumnwfFddiPortDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.2 | ColumnwfFddiPortExtSlot | read-only | mandatory | Slot number associated with a Port entity. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.3 | ColumnwfFddiPortExtNode | read-only | mandatory | Node/connector number associated with a Port entity. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.4 | ColumnwfFddiPortExtCct | read-only | mandatory | Circuit number associated with a Port entity. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.5 | ColumnwfFddiPortExtIndex | read-only | mandatory | A unique value for each PORT associated with each slot/connector pair. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.6 | ColumnwfFddiPortConnectionPolicies | read-only | mandatory | A value representing the PORT's connection policies desired in the node. The value of 'pc-mac-lct' (i.e. PCM MAC LinkConfidence Test) is a term used in the PC_… |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.7 | ColumnwfFddiPortCurrentPath | read-only | mandatory | Indicates the Path(s) into which this PORT is currently inserted. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.8 | ColumnwfFddiPortMacPlacement | read-only | mandatory | Indicates the MAC, if any, whose transmit path exits the station via this PORT. The value shall be zero if there is no MAC associated with the PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.9 | ColumnwfFddiPortAvailablePaths | read-only | mandatory | Indicates the Paths which are available to this Port. In the absence of faults, the A & B ports will always have both the Primary & Secondary paths available. … |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.10 | ColumnwfFddiPortPmdClass | read-only | mandatory | Indicates the Path(s) into which this PORT is currently inserted. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.11 | ColumnwfFddiPortConnectionCapabilities | read-only | mandatory | A value that indicates the connection capabilities of the port. The 'pc-mac-lct' bit indicates that the station has the capability of setting the PC_MAC_LCT Fl… |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.12 | ColumnwfFddiPortEbErrorCts | read-only | mandatory | The count of the number of elasticity buffer errors for a particular PHY. The elasticity buffer is used to account for clock tolerances between stations |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.13 | ColumnwfFddiPortLctFailCts | read-only | mandatory | The count of the consecutive times the link confidence test (LCT) has failed during Connection Management. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.14 | ColumnwfFddiPortLerEstimate | read-only | mandatory | A long term average of the link error rate. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the base 10 logarithm. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.15 | ColumnwfFddiPortLemRejectCts | read-only | mandatory | A link error monitoring count of the times that a link has been rejected. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.16 | ColumnwfFddiPortLemCts | read-only | mandatory | The aggregate link error moniitor error count, set to 0 only on station initialization. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.17 | ColumnwfFddiPortLerCutOff | read-write | mandatory | The link err rate estimate at which a link connection will be broken. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the base 10 log… |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.18 | ColumnwfFddiPortLerAlarm | read-write | mandatory | The link err rate estimate at which a link connection will generate an alarm. It ranges from 10**-4 to 10**-15 and is reported as the absolute value of the bas… |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.19 | ColumnwfFddiPortPcWithhold | read-only | mandatory | A variable from PCM to other management entities containing the reason for withholding a connection. |
| 1.3.6.1.4.1.18.3.4.15.4.3.1.20 | ColumnwfFddiPortHardwarePresent | read-only | mandatory | This variable indicates the presence of underlying hardware support for this port object. |
| 1.3.6.1.4.1.18.3.4.15.4.4 | TablewfFddiPortActionTable | not-accessible | mandatory | A list of Port Action entries. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1 | RowwfFddiPortActionEntry | not-accessible | mandatory | A PORT entry containing actions common to a given PORT. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.1 | ColumnwfFddiPortActionDelete | read-write | mandatory | Create/delete parameter, default = create. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.2 | ColumnwfFddiPortActionSlot | read-only | mandatory | Slot number associated with a PORT action entity. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.3 | ColumnwfFddiPortActionNode | read-only | mandatory | Node/connector number associated with a PORT action entity. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.4 | ColumnwfFddiPortActionCct | read-only | mandatory | Circuit number associated with a PORT action entity. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.5 | ColumnwfFddiPortActionIndex | read-only | mandatory | A unique value for each PORT associated with each slot/connector pair. |
| 1.3.6.1.4.1.18.3.4.15.4.4.1.6 | ColumnwfFddiPortAction | read-write | mandatory | Causes a control signal to be generated with a control_action of 'Signal' and the 'variable' parameter set with the appropriate value (i.e. PC_Maint, PC_Enable… |
| 1.3.6.1.4.1.18.3.4.15.5 | NodewfFddiXGroup | |||
| 1.3.6.1.4.1.18.3.4.15.5.1 | TablewfFddiXLineCfgTable | not-accessible | mandatory | FDDI switch configuration line record |
| 1.3.6.1.4.1.18.3.4.15.5.1.1 | RowwfFddiXLineCfgEntry | not-accessible | mandatory | An FDDI entry containing configuration parameters about an FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.1 | ColumnwfFddiXLineCfgDelete | read-write | mandatory | FDDI interface table create/delete object. The default setting is create. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.2 | ColumnwfFddiXLineCfgEnable | read-write | mandatory | FDDI interface enable/disable object. The default setting is enable. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.3 | ColumnwfFddiXLineCfgLossOfServiceTmo | read-write | mandatory | This timer (in seconds) provides debounce functionality for an FDDI interface. When the FDDI ring becomes non-operational, the LLC interface will be disabled i… |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.4 | ColumnwfFddiXLineCfgSmtEnable | read-write | mandatory | Enable Station Management periodic timers and NIF protocol. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.5 | ColumnwfFddiXLineCfgSmtDatProtocol | read-write | mandatory | SMT will implement an optional ANSI duplicate address test involving periodic transmission of NSA NIF frames addressed to itself if enabled by this attribute. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.6 | ColumnwfFddiXLineCfgLineNumber | read-write | mandatory | Logical line number associated with this driver entity. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.7 | ColumnwfFddiXLineCfgForcePeerTree | read-write | mandatory | This attribute allows all FDDI Peer/Tree connections to reach the 'Thru' state. This is done to give the user some flexibility and allow them to Daisy Chain th… |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.8 | ColumnwfFddiXLineCfgSlot | read-only | mandatory | Chassis slot number of FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.9 | ColumnwfFddiXLineCfgModule | read-only | mandatory | Module number for Fiddlestix platform, filled in by driver. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.10 | ColumnwfFddiXLineCfgActualNode | read-only | mandatory | Actual Node number for this FDDI interface, filled in by the driver. |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.11 | ColumnwfFddiXLineCfgNode | read-only | mandatory | Instance ID node - filled in by driver. This attribute is an encoded value and is equal to 'module'*100 + 'node'. Where 'module' is defined in object 4 and 'no… |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.12 | ColumnwfFddiXLineCfgSmtIndex | read-write | mandatory | Used for indexing into rfc1512 MIBS, this value is gotten from multiplying the 'slot*1000' and then adding the 'wfFddiXLineCfgNode' attribute described above. … |
| 1.3.6.1.4.1.18.3.4.15.5.1.1.13 | ColumnwfFddiXLineCfgIfIndex | read-only | mandatory | An index value that uniquely identifies an interface to a FDDI-like medium. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.18.3.4.15.5.2 | TablewfFddiXLineTable | not-accessible | mandatory | FDDI switch statistic line record |
| 1.3.6.1.4.1.18.3.4.15.5.2.1 | RowwfFddiXLineEntry | not-accessible | mandatory | An FDDI entry containing information about an FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.1 | ColumnwfFddiXLineSlot | read-only | mandatory | Chassis slot number of FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.2 | ColumnwfFddiXLineModule | read-only | mandatory | Module number for Fiddlestix platform, filled in by driver. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.3 | ColumnwfFddiXLineActualNode | read-only | mandatory | Actual Node number for this FDDI interface, filled in by the driver. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.4 | ColumnwfFddiXLineNode | read-only | mandatory | Instance ID node - filled in by driver. This attribute is an encoded value and is equal to 'module'*10 + 'node'. Where 'module' is defined in object 4 and 'nod… |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.5 | ColumnwfFddiXLineSmtIndex | read-write | mandatory | Logical line number associated with this FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.6 | ColumnwfFddiXLineIfIndex | read-only | mandatory | An index value that uniquely identifies an interface to a FDDI-like medium. The interface identified by a particular value of this index is the same interface … |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.7 | ColumnwfFddiXLineTxErrors | read-only | mandatory | An aggregate of the total number of transmit errors on this FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.8 | ColumnwfFddiXLineTxAborts | read-only | mandatory | Number of transmitted frames terminated (i.e. aborted) abnormally by the MAC. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.9 | ColumnwfFddiXLineTxOverruns | read-only | mandatory | Number of tranmitter overruns experienced by this interface. May indicate a HW problem with regards to the DMAC feeding the MAC. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.10 | ColumnwfFddiXLineTxUnderruns | read-only | mandatory | Number of tranmitter underruns experienced by this interface. May indicate a SW problem with regards to replenishing the DMACs XMT descriptor. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.11 | ColumnwfFddiXLineRxErrors | read-only | mandatory | An aggregate of the total number of receive errors on this FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.12 | ColumnwfFddiXLineRxCrcErrors | read-only | mandatory | Number of LLC frames received with CRC errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.13 | ColumnwfFddiXLineRxSmtCrcErrors | read-only | mandatory | Number of SMT frames received with CRC errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.14 | ColumnwfFddiXLineRxInvalidFrameStatusErrors | read-only | mandatory | A count of the number of badly formed LLC frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 … |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.15 | ColumnwfFddiXLineRxSmtInvalidFrameStatusErrors | read-only | mandatory | A count of the number of badly formed SMT frames received off of the FDDI ring. These are frames which do not contain a valid Frame Status field of at least 3 … |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.16 | ColumnwfFddiXLineRxMacErrors | read-only | mandatory | Number of LLC frames received with MAC errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.17 | ColumnwfFddiXLineRxSmtMacErrors | read-only | mandatory | Number of SMT frames received with MAC errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.18 | ColumnwfFddiXLineRxFormatErrors | read-only | mandatory | Number of LLC frames received with Format errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.19 | ColumnwfFddiXLineRxSmtFormatErrors | read-only | mandatory | Number of SMT frames received with Format errors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.20 | ColumnwfFddiXLineRxFragmentErrors | read-only | mandatory | Number of LLC frame fragments received. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.21 | ColumnwfFddiXLineRxSmtFragmentErrors | read-only | mandatory | Number of SMT frame fragments received. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.22 | ColumnwfFddiXLineRxInvalidLengthErrors | read-only | mandatory | Number of LLC frames received with an ending T symbol which are either too short or contain an odd number of symbols. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.23 | ColumnwfFddiXLineRxSmtInvalidLengthErrors | read-only | mandatory | Number of SMT frames received with an ending T symbol which are either too short or contain an odd number of symbols. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.24 | ColumnwfFddiXLineRxAbortErrors | read-only | mandatory | Number of LLC frames aborted during reception. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.25 | ColumnwfFddiXLineRxSmtAbortErrors | read-only | mandatory | Number of LLC frames aborted during reception. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.26 | ColumnwfFddiXLineRxEDataUnknownErrors | read-only | mandatory | Number of LLC frames received with the Error indication set, that we couldn't decode as were unable to get the END_DATA value from the frame. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.27 | ColumnwfFddiXLineRxSmtEDataUnknownErrors | read-only | mandatory | Number of SMT frames received with the Error indication set, that we couldn't decode as were unable to get the END_DATA value from the frame. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.28 | ColumnwfFddiXLineRxLastEDataFStatusErrorVal | read-only | mandatory | The value of END_DATA and FRAME_STATUS from the last LLC frame received containing an error. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.29 | ColumnwfFddiXLineRxSmtLastEDataFStatusErrorVal | read-only | mandatory | The value of END_DATA and FRAME_STATUS from the last SMT frame received containing an error. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.30 | ColumnwfFddiXLineRxOverruns | read-only | mandatory | Number of receiver overruns experienced by this interface. May indicate a SW problem with regards to replenishing the DMACs RCV descriptors. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.31 | ColumnwfFddiXLineRxUnderruns | read-only | mandatory | Number of receiver underruns experienced by this interface. May indicate a HW problem with regards to the DMAC feeding the MAC. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.32 | ColumnwfFddiXLineRxOversizedFrames | read-only | mandatory | Number of LLC frames received whose length exceeded the MTU. (Note: The MTU is defined in rfc1573 in the ifMtu object.) |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.33 | ColumnwfFddiXLineRxSmtOversizedFrames | read-only | mandatory | Number of SMT frames received whose length exceeded the MTU. (Note: The MTU is defined in rfc1573 in the ifMtu object.) |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.34 | ColumnwfFddiXLineRxUndersizedFrames | read-only | mandatory | Number of LLC frames received whose length was less than 20 bytes, including the FC byte and a 4 byte CRC. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.35 | ColumnwfFddiXLineRxSmtUndersizedFrames | read-only | mandatory | Number of SMT frames received whose length was less than 37 bytes, including the FC byte and a 4 byte CRC. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.36 | ColumnwfFddiXLineRxSmtSecondaryNsaFrames | read-only | mandatory | Number of Secondary NSA frames received by this interface and dropped. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.37 | ColumnwfFddiXLineUnexpectedFrames | read-only | mandatory | Number of non-LLC and non SMT frames received by this interface. Does NOT include MAC frames or Void frames. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.38 | ColumnwfFddiXLineRxSmtOctets | read-only | mandatory | Number of bytes received without error. This byte count only includes SMT frames (i.e. no MAC and LLC frames). |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.39 | ColumnwfFddiXLineRxSmtFrames | read-only | mandatory | Number of frames received without error. This frame count only includes SMT frames (i.e. no MAC and LLC frames). |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.40 | ColumnwfFddiXLineTxSmtOctets | read-only | mandatory | Number of bytes transmitted. This byte count only includes SMT frames (i.e. no MAC and LLC frames). Also note that this value is an approximation in that its a… |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.41 | ColumnwfFddiXLineTxSmtFrames | read-only | mandatory | Number of frames transmitted. This frame count only includes SMT frames (i.e. no MAC and LLC frames). Also note that this value is an approximation in that its… |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.42 | ColumnwfFddiXLinePhyALogPtr | read-only | mandatory | Address of the Debug Phy Event Buffer for Phy A. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| 1.3.6.1.4.1.18.3.4.15.5.2.1.43 | ColumnwfFddiXLinePhyBLogPtr | read-only | mandatory | Address of the Debug Phy Event Buffer for Phy B. This attribute is strictly for diagnostic purposes. The size of the buffer is 1028 bytes. |
| 1.3.6.1.4.1.18.3.4.15.5.3 | TablewfFddiXSmtTable | not-accessible | mandatory | A list of SMT entries. |
| 1.3.6.1.4.1.18.3.4.15.5.3.1 | RowwfFddiXSmtEntry | not-accessible | mandatory | An FDDI entry containing information about an FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.3.1.1 | ColumnwfFddiXSmtIndex | read-only | mandatory | A unique value for each SMT. The value for each SMT must remain constant at least from one re- initialization of the entity's network management system to the … |
| 1.3.6.1.4.1.18.3.4.15.5.3.1.2 | ColumnwfFddiXSmtManufacturerData | read-only | mandatory | Contains 32 Octets of manufacturer data. The first component, manufacturing OUI, is the 3 octet Organizationally Unique Identifier (OUI) assigned by IEEE. The … |
| 1.3.6.1.4.1.18.3.4.15.5.4 | TablewfFddiXMacTable | not-accessible | mandatory | A list of MAC entries. |
| 1.3.6.1.4.1.18.3.4.15.5.4.1 | RowwfFddiXMacEntry | not-accessible | mandatory | An FDDI entry containing information about an FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.4.1.1 | ColumnwfFddiXMacSmtIndex | read-only | mandatory | The value of the SMT index associated with this MAC. |
| 1.3.6.1.4.1.18.3.4.15.5.4.1.2 | ColumnwfFddiXMacIndex | read-only | mandatory | Index variable for uniquely identifying the MAC object instances, which is the same as the corresponding resource index in SMT. |
| 1.3.6.1.4.1.18.3.4.15.5.4.1.3 | ColumnwfFddiXMacBridgeFunctions | read-only | mandatory | |
| 1.3.6.1.4.1.18.3.4.15.5.4.1.4 | ColumnwfFddiXMacDuplicateTokenCts | read-only | mandatory | The count of the number of times a Duplicate Token has been detected. |
| 1.3.6.1.4.1.18.3.4.15.5.5 | TablewfFddiXPortTable | not-accessible | mandatory | A list of PORT Entries. |
| 1.3.6.1.4.1.18.3.4.15.5.5.1 | RowwfFddiXPortEntry | not-accessible | mandatory | An FDDI entry containing information about an FDDI interface. |
| 1.3.6.1.4.1.18.3.4.15.5.5.1.1 | ColumnwfFddiXPortSmtIndex | read-only | mandatory | The value of the SMT index associated with this PORT. |
| 1.3.6.1.4.1.18.3.4.15.5.5.1.2 | ColumnwfFddiXPortIndex | read-only | mandatory | A unique value for each PORT within a given SMT, which is the same as the corresponding resource index in SMT. The value for each PORT must remain constant at … |
| 1.3.6.1.4.1.18.3.4.15.5.5.1.3 | ColumnwfFddiXPortEbErrors | read-only | mandatory | The count of the number of elasticity buffer errors for a particular PHY. The elasticity buffer is used to account for clock tolerances between stations. |