Wellfleet-FR-MIB
50 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.9.1.1 | TablewfFrDlcmiTable | not-accessible | mandatory | The Parameters for the Data Link Connection Management Interface |
| 1.3.6.1.4.1.18.3.5.9.1.1.1 | RowwfFrDlcmiEntry | not-accessible | mandatory | The parameters for a particular Data Link Connection Management Interface |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.1 | ColumnwfFr1DlcmiDelete | read-write | mandatory | Indication to delete this frame relay interface |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.2 | ColumnwfFr1DlcmiDisable | read-write | mandatory | Indicates when a dlcmi entry is to be enabled or disabled. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.3 | ColumnwfFr1DlcmiState | read-only | mandatory | The current state of Frame Relay. The not present state is not actually valid except when the record is first added. It is included for consistency. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.4 | ColumnwfFr1DlcmiCircuit | read-only | mandatory | Instance identifier. The circuit number of this entry |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.5 | ColumnwfFr1DlcmiManagementType | read-write | mandatory | This variable indicates which Data Link Connection Management scheme is active (and by implication, what DLCI it uses). |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.6 | ColumnwfFr1DlcmiStatus | read-only | mandatory | Indicates the status of the interface. FR1_STATUS_START is the state during rebooting or initial start of circuit FR1_STATUS_RUNNING1 is the sate after the cir… |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.7 | ColumnwfFr1DlcmiAddress | read-write | mandatory | This states which address format is in use on the FR interface. The default is Q922 |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.8 | ColumnwfFr1DlcmiAddressLen | read-write | mandatory | This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the address includeding the control po… |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.9 | ColumnwfFr1DlcmiPollingInterval | read-write | mandatory | The number of seconds between successive status enquiry messages |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.10 | ColumnwfFr1DlcmiFullEnquiryInterval | read-write | mandatory | The number of status enquiry intervals that pass before issuance of a full status enquiry message. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.11 | ColumnwfFr1DlcmiErrorThreshold | read-write | mandatory | This is the maximum number of unanswered Status Enquiries the equipment shall accept before declaring the interface down. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.12 | ColumnwfFr1DlcmiMonitoredEvents | read-write | mandatory | This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station… |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.13 | ColumnwfFr1DlcmiMaxSupportedVCs | read-only | mandatory | The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. The system sets this initially. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.14 | ColumnwfFr1DlcmiMulticast | read-write | mandatory | This indicates whether the frame relay provider offers a multicast |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.15 | ColumnwfFr1DlcmiSeqCount | read-only | mandatory | This station's sequence counter. It represents the next value to send. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.16 | ColumnwfFr1DlcmiLastReceived | read-only | mandatory | The sequence number just received from the switch. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.17 | ColumnwfFr1DlcmiPassiveSeqCount | read-only | mandatory | This station's sequence counter for answering status enquiry. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.18 | ColumnwfFr1DlcmiPassiveReceived | read-only | mandatory | The sequence number just received from the enquring station. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.19 | ColumnwfFr1DlcmiPolls | read-only | mandatory | This is the counter of where we are in the polling cycle. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.20 | ColumnwfFr1DlcmiAlarmTimer | read-only | mandatory | This is a counter of 1/2 second timeouts. When it reaches 2 x the polling interval, an enquiry message is sent. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.21 | ColumnwfFr1ErrType | read-only | mandatory | Indicate the type of the last specific monitored error. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.22 | ColumnwfFr1ErrData | read-only | mandatory | Contains as much of the error packet as possible. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.23 | ColumnwfFr1ErrTime | read-only | mandatory | The time the last error occurred. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.24 | ColumnwfFr1ErrDiscards | read-only | mandatory | The number of inbound frames dropped because of format or other errors or because the VC was not known. |
| 1.3.6.1.4.1.18.3.5.9.1.1.1.25 | ColumnwfFr1ErrDrops | read-only | mandatory | The number of outbound frames dropped. Usually this is due the specified DLCI being unknown or a broadcast packet is too long |
| 1.3.6.1.4.1.18.3.5.9.1.2 | TablewfFrCircuitTable | not-accessible | mandatory | Frame Relay Circuit table gives information about a virtual circuits. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1 | RowwfFrCircuitEntry | not-accessible | mandatory | An entry in the Frame Relay Circuit table. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.1 | ColumnwfFr1CircuitDelete | read-write | mandatory | Indication to delete this frame relay interface. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.2 | ColumnwfFr1CircuitNumber | read-only | mandatory | Instance identifier. The circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.3 | ColumnwfFr1CircuitDlci | read-only | mandatory | Instance identifier. This indicates which virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.4 | ColumnwfFr1CircuitState | read-only | mandatory | Indicates the state of the particular virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.5 | ColumnwfFr1CircuitStateSet | read-write | mandatory | User access for setting the state of a virtual circuit |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.6 | ColumnwfFr1CircuitReceivedFECNs | read-only | mandatory | Number of frames received indicating forward congestion. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.7 | ColumnwfFr1CircuitReceivedBECNs | read-only | mandatory | Number of frames received indicating backward congestion. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.8 | ColumnwfFr1CircuitSentFrames | read-only | mandatory | The number of frames sent from this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.9 | ColumnwfFr1CircuitSentOctets | read-only | mandatory | The number of octets sent from this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.10 | ColumnwfFr1CircuitReceivedFrames | read-only | mandatory | The number of frames received from this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.11 | ColumnwfFr1CircuitReceivedOctets | read-only | mandatory | The number of octets received from this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.12 | ColumnwfFr1CircuitCreationTime | read-only | mandatory | The value of sysUpTime when the vc was created. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.13 | ColumnwfFr1CircuitLastTimeChange | read-only | mandatory | The value of sysUpTime when last there was a change in vc state. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.14 | ColumnwfFr1CircuitCommittedBurst | read-write | mandatory | Indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval. Wellfleet does not… |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.15 | ColumnwfFr1CircuitExcessBurst | read-write | mandatory | Indicates teh maximum amount of uncommitted data bits that the network will attempt to deliver over the measurement interval. Wellfleet does not presently supp… |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.16 | ColumnwfFr1CircuitThroughput | read-write | mandatory | This is the average number of 'Frame Relay Information Field' bits transferred per second across a user network interface in one direction, measured over the m… |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.17 | ColumnwfFr1CircuitMulticast | read-write | mandatory | Indicates whether this DLCI is used for multicast or single destination. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.18 | ColumnwfFr1CircuitDiscards | read-only | mandatory | The number of inbound frames discarded because of format errors, because the VC is inactive or because the protocol was not registered for this circuit. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.19 | ColumnwfFr1CircuitDrops | read-only | mandatory | Indicates how many outbound frames were dropped. Usually these are dropped because the VC is not active. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.20 | ColumnwfFr1CircuitSubCct | read-write | mandatory | Circuit number to use for this VC when configured in hybrid (for bridging) or direct access (VC as a circuit) mode. |
| 1.3.6.1.4.1.18.3.5.9.1.2.1.21 | ColumnwfFr1CircuitMode | read-write | mandatory | The mode of the given VC. GROUP - treats the VC as one of many vc's on a circuit. HYBRID - treats the VC as one of many vc's on a circuit for protocol traffic,… |