Wellfleet-FRSW-MIB
458 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.9.6.1 | TablewfFrSwDlcmiTable | not-accessible | mandatory | The Parameters for the Data Link Connection Management Interface corresponding to any interface. Incorporates the Error table. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1 | RowwfFrSwDlcmiEntry | not-accessible | mandatory | The parameters for a particular Data Link Connection Management Interface. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.1 | ColumnwfFrSwDlcmiDelete | read-write | mandatory | Indication to delete this frame relay interface. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.2 | ColumnwfFrSwDlcmiState | read-only | mandatory | Indicates which state of DLCMI the interface is in |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.3 | ColumnwfFrSwDlcmiNniEnable | read-write | mandatory | Indicates whether a NNI is enabled for this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.4 | ColumnwfFrSwDlcmiCircuit | read-only | mandatory | Instance identifier; the circuit number of this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.5 | ColumnwfFrSwDlcmiManagementType | read-write | mandatory | Indicates the Data Link Connection Management scheme that is active. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.6 | ColumnwfFrSwL3NetAddress | read-write | mandatory | Indicates level 3 (IP) address of this frame relay interface |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.7 | ColumnwfFrSwDlcmiAddressLen | read-write | mandatory | Indicates the address length, including the control portion. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.8 | ColumnwfFrSwDlcmiControlByteDisable | read-write | mandatory | Indicates inclusion of control byte in q922 format. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.9 | ColumnwfFrSwDlcmiPollingInterval | read-write | mandatory | The number of seconds between successive status enquiry messages. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.10 | ColumnwfFrSwDlcmiFullEnquiryInterval | read-write | mandatory | Indicates the number of status enquiries before a full status enquiry. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.11 | ColumnwfFrSwDlcmiErrorThreshold | read-write | mandatory | Indicates the number errors monitored before declaring the interface down. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.12 | ColumnwfFrSwDlcmiMonitoredEvents | read-write | mandatory | Indicates the events over which error threshold is kept. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.13 | ColumnwfFrSwDlcmiRecoveryCounts | read-only | mandatory | Indicates the number of correct polling cycles during recovery. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.14 | ColumnwfFrSwDlcmiMaxSupportedVCs | read-write | mandatory | Indicates the maximum number of VCs allowed. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.15 | ColumnwfFrSwDlcmiVCsInUse | read-only | mandatory | Indicates the number of VCs that are currently configured on this interface. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.16 | ColumnwfFrSwSwitchHdrErrors | read-only | mandatory | Indicates the number of frames dropped because they were received on the remote side with an invalid switch header. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.17 | ColumnwfFrSwDlcmiSequenceCount | read-only | mandatory | Indicates this switch's sequence counter; value of next to send. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.18 | ColumnwfFrSwDlcmiLastReceived | read-only | mandatory | Indicates the sequence number just received from the end station. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.19 | ColumnwfFrSwDlcmiActiveSeqCount | read-only | mandatory | Indicates the switch's sequence counter for sending status enquiry. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.20 | ColumnwfFrSwDlcmiActiveReceived | read-only | mandatory | Indicates the sequence number just received from the enquiring station. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.21 | ColumnwfFrSwDlcmiPolls | read-only | mandatory | This is the counter of where we are in the polling cycle. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.22 | ColumnwfFrSwDlcmiAlarmTimer | read-only | mandatory | Counter of 1/2 second timeouts. Indicates when to expect poll. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.23 | ColumnwfFrSwErrType | read-only | mandatory | Indicates the type of the last specific monitored error. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.24 | ColumnwfFrSwErrData | read-only | mandatory | Contains as much of the error packet as possible. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.25 | ColumnwfFrSwErrTime | read-only | mandatory | Indicates the time the last error occurred. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.26 | ColumnwfFrSwBcMeasurementInterval | read-write | mandatory | Indicates the Committed Burst sample window interval in msec |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.27 | ColumnwfFrSwDlcmiMcastNoBufferErrors | read-only | mandatory | Indicates the number of times a multicast failed partially or wholly because there are insufficient buffers available to create multiple copies of a multicast … |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.28 | ColumnwfFrSwDlcmiFrameTooShortErrors | read-only | mandatory | Indicates the number of frames dropped that are too short to be accepted. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.29 | ColumnwfFrSwDlcmiFrameTooLongErrors | read-only | mandatory | Indicates the number of frames dropped that are too long to be accepted. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.30 | ColumnwfFrSwDlcmiIllegalDlciErrors | read-only | mandatory | Indicates the number of frames dropped that had an invalid DLCI value. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.31 | ColumnwfFrSwDlcmiUnknownDlciErrors | read-only | mandatory | Indicates the number of frames dropped which had an unknown DLCI value. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.32 | ColumnwfFrSwDlcmiProtocolErrors | read-only | mandatory | Indicates the number of frames dropped because of a DLCMI protocol violation. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.33 | ColumnwfFrSwDlcmiUnknownIEErrors | read-only | mandatory | Indicates the number of frames dropped that had an unknown information element. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.34 | ColumnwfFrSwDlcmiSequenceErrors | read-only | mandatory | Indicates the number of frames dropped because of a DLCMI sequence error. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.35 | ColumnwfFrSwDlcmiUnknownRPTErrors | read-only | mandatory | Indicates the number of frames dropped which had an unknown report type. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.36 | ColumnwfFrSwDlcmiControlByteErrors | read-only | mandatory | Indicates the number of frames dropped that had an unsupported control byte. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.37 | ColumnwfFrSwDlcmiFormatErrors | read-only | mandatory | Indicates the number of frames dropped due to a frame format error. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.38 | ColumnwfFrSwDlcmiOtherErrors | read-only | mandatory | Indicates the number of frames dropped due to unknown or other errors not counted by any error counter. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.39 | ColumnwfFrSwDlcmiStatus | read-only | mandatory | Indicates which state of execution the DLCMI gate is in |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.40 | ColumnwfFrSwDlcmiNewVCs | read-only | mandatory | Indicates the number of newly added PVCs that we have not yet told the CPE about, by means of a full-status message. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.41 | ColumnwfFrSwDlcmiDeletedVCs | read-only | mandatory | Indicates the number of deletedly added PVCs that we have not yet told the CPE about, by means of a full-status message. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.42 | ColumnwfFrSwDlcmiFullStatusSeq | read-only | mandatory | Indicates the expected sequence number for the next Status Enquiry message that will prove that the CPE received our last Full Status Message and knows about t… |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.43 | ColumnwfFrSwDlcmiBidirect | read-write | mandatory | Indication to delete this frame relay interface. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.44 | ColumnwfFrSwDlcmiDteStatus | read-only | mandatory | Indicates which state of execution the DLCMI gate is in for bidirectional procedures. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.45 | ColumnwfFrSwDlcmiDteSeqCount | read-only | mandatory | Indicates the switch's sequence counter for sending status enquiry. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.46 | ColumnwfFrSwDlcmiDteReceived | read-only | mandatory | Indicates the sequence number just received from the enquiring station. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.47 | ColumnwfFrSwDlcmiDteLastReceived | read-only | mandatory | Indicates the sequence number just received from the end station. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.48 | ColumnwfFrSwDlcmiDtePolls | read-only | mandatory | This is the counter of where we are in the polling cycle. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.49 | ColumnwfFrSwDlcmiDtePollingInterval | read-write | mandatory | The number of seconds between successive status enquiry messages. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.50 | ColumnwfFrSwDlcmiDteFullEnquiryInterval | read-write | mandatory | Indicates the number of status enquiries before a full status enquiry. (For bidirectional procedures.) |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.51 | ColumnwfFrSwDlcmiDteErrorThreshold | read-write | mandatory | Indicates the number errors monitored before declaring the interface down. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.52 | ColumnwfFrSwDlcmiCrossNetEnable | read-write | mandatory | Indication to delete this frame relay interface. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.53 | ColumnwfFrSwDlcmiCrossNetPollingInterval | read-write | mandatory | The number of seconds between successive status enquiry messages. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.54 | ColumnwfFrSwDlcmiCrossNetErrorThreshold | read-write | mandatory | Indicates the number missed heartbeat polls before declaring the cross-net PVC inactive. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.55 | ColumnwfFrSwDlcmiCrossNetAsyncUpdateEnable | read-write | mandatory | Indicates whether we are to send to the other end of the network, status updates for dlcis as soon as there is a change of status for the dlci. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.56 | ColumnwfFrSwDlcmiBcMeasurementEnable | read-write | mandatory | Indicates whether Committed Burst Measurement is enabled for this interface. If this attribute is set to DISABLE then DE bit setting in Frame Relay frames at t… |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.57 | ColumnwfFrSwDlcmiAsyncUpdateEnable | read-write | mandatory | Indicates whether the link management entity should send an asynchronous single PVC update message when the state of a PVC is changed by a technician or by cro… |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.58 | ColumnwfFrSwDlcmiCrossNetListenEnable | read-write | mandatory | Indicates whether the link management entity should make a judgement of the PVC's status based on Cross Net updates. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.59 | ColumnwfFrSwDlcmiSvcDisable | read-write | mandatory | Indicates whether SVC is enabled or disabled for this access channel. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.60 | ColumnwfFrSwDlcmiL2AddrType | read-write | mandatory | Indicates the address type supported on this access channel. This information is needed when wFrSwDlcmiSVCDisable is enabled. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.61 | ColumnwfFrSwDlcmiEscapeMode | read-write | mandatory | Identifies the Escape mode (none, ingress or egress) to be used for PVCs with wfFrSwVcEscapeMode set to enabled. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.62 | ColumnwfFrSwDlcmiEscapeCircuit | read-write | mandatory | Identifies the FR-DTE circuit number corresponding to an Escape PVC. Applies only to PVCs with wfFrSwVcEscapeEnable set to enabled. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.63 | ColumnwfFrSwDlcmiEscapeVcCount | read-write | mandatory | The number of PVCs on this DLCMI that are configured as Escape VCs |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.64 | ColumnwfFrSwDlcmiIwfMode | read-write | mandatory | Identifies the interworking mode (none, SDLC-to-FRSW) to be used for PVCs with wfFrSwVcEscapeMode set to enabled. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.65 | ColumnwfFrSwDlcmiSvcBillingEnable | read-write | mandatory | Indicates whether the SVC Billing on this access channel set to enable. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.66 | ColumnwfFrSwDlcmiSpvcAgent | read-write | mandatory | Indicates if an SPVC Call Request Agent, Call Accept Agent, or both are enabled on this FRSW circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.1.1.67 | ColumnwfFrSwDlcmiCallAccDlciSelectionType | read-write | mandatory | Indicates to the Call Accept Agent to accept SPVC Call Setup requests for any available DLCI or for a specific DLCI. Call Setup requests with the wrong selecti… |
| 1.3.6.1.4.1.18.3.5.9.6.2 | TablewfFrSwCctTable | not-accessible | obsolete | Frame Relay Circuit table gives information about a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1 | RowwfFrSwCctEntry | not-accessible | obsolete | An entry in the Frame Relay (Virtual) Circuit table. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.1 | ColumnwfFrSwCctDelete | read-write | obsolete | Indication to delete this frame relay interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.2 | ColumnwfFrSwCctNumber | read-only | obsolete | Instance identifier; the circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.3 | ColumnwfFrSwCctDlci | read-only | obsolete | Instance identifier; this indicates the virtual circuit identifier |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.4 | ColumnwfFrSwCctState | read-only | obsolete | Indicates whether the particular virtual circuit is operational. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.5 | ColumnwfFrSwCctMulticast | read-write | obsolete | Indicates whether this dlci is used for multicast or single destination. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.6 | ColumnwfFrSwCctInBc | read-only | obsolete | Indicates the Incoming Committed Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.7 | ColumnwfFrSwCctOutBc | read-only | obsolete | Indicates the Outgoing Committed Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.8 | ColumnwfFrSwCctInBe | read-write | obsolete | Indicates the Incoming Excess Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.9 | ColumnwfFrSwCctOutBe | read-write | obsolete | Indicates the Outgoing Excess Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.10 | ColumnwfFrSwCctInThroughput | read-write | obsolete | Indicates the incoming throughput in bits/sec for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.11 | ColumnwfFrSwCctOutThroughput | read-write | obsolete | Indicates the outgoing throughput in bits/sec for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.12 | ColumnwfFrSwCctCreationTime | read-only | obsolete | Indicates the value of sysUpTime when the VC was created. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.13 | ColumnwfFrSwCctLastTimeChange | read-only | obsolete | Indicates the value of sysUpTime when last there was a change in VC state. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.14 | ColumnwfFrSwCctLocalSentNonDEFrames | read-only | obsolete | Indicates the number of frames without the DE bit sent on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.15 | ColumnwfFrSwCctLocalSentNonDEOctets | read-only | obsolete | Indicates the number of octets without DE bit sent on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.16 | ColumnwfFrSwCctLocalSentDEFrames | read-only | obsolete | Indicates the number of frames with DE bit set sent on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.17 | ColumnwfFrSwCctLocalSentDEOctets | read-only | obsolete | Indicates the number of octets with DE bit set sent on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.18 | ColumnwfFrSwCctLocalSetFECNFrames | read-only | obsolete | Indicates the number of frames sent to the local interface on which this switch set the FECN bit . |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.19 | ColumnwfFrSwCctLocalSetFECNOctets | read-only | obsolete | Indicates the number of octets in frames sent to the local interface on which this switch set the FECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.20 | ColumnwfFrSwCctLocalSetBECNFrames | read-only | obsolete | Indicates the number of frames sent to the local interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.21 | ColumnwfFrSwCctLocalSetBECNOctets | read-only | obsolete | Indicates the number of octets in frames sent to the local interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.22 | ColumnwfFrSwCctLocalSetDEFrames | read-only | obsolete | Indicates the number of frames sent to the local interface on which this switch set the DE bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.23 | ColumnwfFrSwCctLocalSetDEOctets | read-only | obsolete | Indicates the number of octets in frames sent to the local interface on which this switch set the DE bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.24 | ColumnwfFrSwCctLocalDropNonDEFrames | read-only | obsolete | Indicates the number of frames received over the local interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.25 | ColumnwfFrSwCctLocalDropNonDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the local interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.26 | ColumnwfFrSwCctLocalDropDEFrames | read-only | obsolete | Indicates the number of frames received over the local interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.27 | ColumnwfFrSwCctLocalDropDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the local interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.28 | ColumnwfFrSwCctInactiveVCDropFrames | read-only | obsolete | Indicates how many frames were discarded because the virtual circuit was inactive. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.29 | ColumnwfFrSwCctInactiveVCDropOctets | read-only | obsolete | Indicates how many Octets were discarded because the virtual circuit was inactive. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.30 | ColumnwfFrSwCctLocalRecvNonDEFrames | read-only | obsolete | Indicates the number of frames received on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.31 | ColumnwfFrSwCctLocalRecvNonDEOctets | read-only | obsolete | Indicates the number of octets received on this virtual circuit over the local interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.32 | ColumnwfFrSwCctLocalRecvDEFrames | read-only | obsolete | Indicates the number of frames received over the local interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.33 | ColumnwfFrSwCctLocalRecvDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the local interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.34 | ColumnwfFrSwCctLocalRecvFECNFrames | read-only | obsolete | Indicates the number of frames received over the local interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.35 | ColumnwfFrSwCctLocalRecvFECNOctets | read-only | obsolete | Indicates the number of octets in frames received over the local interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.36 | ColumnwfFrSwCctLocalRecvBECNFrames | read-only | obsolete | Indicates the number of frames received over the local interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.37 | ColumnwfFrSwCctLocalRecvBECNOctets | read-only | obsolete | Indicates the number of octets in frames received over the local interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.38 | ColumnwfFrSwCctLocalRecentNonDEOctets | read-only | obsolete | Indicates the number of octets received over the local interface during the most recent sampling period. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.39 | ColumnwfFrSwCctRemoteSentNonDEFrames | read-only | obsolete | Indicates the number of Non DE set frames sent over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.40 | ColumnwfFrSwCctRemoteSentNonDEOctets | read-only | obsolete | Indicates the number of Non DE set octets sent over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.41 | ColumnwfFrSwCctRemoteSentDEFrames | read-only | obsolete | Indicates the number of DE set frames sent over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.42 | ColumnwfFrSwCctRemoteSentDEOctets | read-only | obsolete | Indicates the number of DE set octets sent over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.43 | ColumnwfFrSwCctRemoteSetFECNFrames | read-only | obsolete | Indicates the number of frames sent to the remote interface on which this switch set the FECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.44 | ColumnwfFrSwCctRemoteSetFECNOctets | read-only | obsolete | Indicates the number of octets in frames sent to the remote interface that on which this switch set the FECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.45 | ColumnwfFrSwCctRemoteSetBECNFrames | read-only | obsolete | Indicates the number of frames sent to the remote interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.46 | ColumnwfFrSwCctRemoteSetBECNOctets | read-only | obsolete | Indicates the number of octets in frames sent to the remote interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.47 | ColumnwfFrSwCctRemoteDropNonDEFrames | read-only | obsolete | Indicates the number of frames received over the remote interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.48 | ColumnwfFrSwCctRemoteDropNonDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the remote interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.49 | ColumnwfFrSwCctRemoteDropDEFrames | read-only | obsolete | Indicates the number of frames received over the remote interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.50 | ColumnwfFrSwCctRemoteDropDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the remote interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.51 | ColumnwfFrSwCctRemoteRecvNonDEFrames | read-only | obsolete | Indicates the number of frames received on this virtual circuit over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.52 | ColumnwfFrSwCctRemoteRecvNonDEOctets | read-only | obsolete | Indicates the number of octets received on this virtual circuit over the remote interface. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.53 | ColumnwfFrSwCctRemoteRecvDEFrames | read-only | obsolete | Indicates the number of frames received over the remote interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.54 | ColumnwfFrSwCctRemoteRecvDEOctets | read-only | obsolete | Indicates the number of octets in frames received over the remote interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.55 | ColumnwfFrSwCctRemoteRecvFECNFrames | read-only | obsolete | Indicates the number of frames received over the remote interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.56 | ColumnwfFrSwCctRemoteRecvFECNOctets | read-only | obsolete | Indicates the number of octets in frames received over the remote interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.57 | ColumnwfFrSwCctRemoteRecvBECNFrames | read-only | obsolete | Indicates the number of frames received over the remote interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.58 | ColumnwfFrSwCctRemoteRecvBECNOctets | read-only | obsolete | Indicates the number of octets in frames received over the remote interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.59 | ColumnwfFrSwCctLocalBecnState | read-only | obsolete | Indicates the local BECN state |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.60 | ColumnwfFrSwCctRemoteBecnState | read-only | obsolete | Indicates the remote BECN state |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.61 | ColumnwfFrSwCctLocalOrRemoteConnection | read-only | obsolete | Indicates whether this connection is Local to Local Connection or Local to Remote connection. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.62 | ColumnwfFrSwCctInBcOctets | read-only | obsolete | Indicates the Incoming Committed Burst in octets for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.63 | ColumnwfFrSwCctStateSet | read-write | obsolete | User access for setting the state of a virtual circuit |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.64 | ColumnwfFrSwCctReportedStatus | read-only | obsolete | Record keeping for circuit status |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.65 | ColumnwfFrSwCctReceivedStatus | read-only | obsolete | State of a virtual circuit as reported by the network at an NNI |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.66 | ColumnwfFrSwCctCrossNetStatus | read-only | obsolete | State of a virtual circuit as reported by the other end of the network under bidirectional signalling. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.67 | ColumnwfFrSwCctXNetSent | read-only | obsolete | Whether we have sent a cross net status message for this VC yet. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.68 | ColumnwfFrSwCctXNetReceived | read-only | obsolete | Whether we have received a cross net status message for this VC during the current polling interval. |
| 1.3.6.1.4.1.18.3.5.9.6.2.1.69 | ColumnwfFrSwCctXNetErrors | read-only | obsolete | This is the count of the consecutive errors (usually timeouts) against this VC in cross-network heartbeat polling |
| 1.3.6.1.4.1.18.3.5.9.6.3 | TablewfFrSwTupleTable | not-accessible | obsolete | The Parameters for the Tuple table, identifying the endpoints of virtual circuits as pairs of IP addresses and DLCI. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1 | RowwfFrSwTupleEntry | not-accessible | obsolete | The parameters for a particular Tuple. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1.1 | ColumnwfFrSwTupleDelete | read-write | obsolete | Indication to delete this tuple. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1.2 | ColumnwfFrSwTupleIpAddrA | read-only | obsolete | Instance indentifier; indicates the IP address associated with endpoint 'A' of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1.3 | ColumnwfFrSwTupleDlciA | read-only | obsolete | Instance identfier; indicates the DLCI associated with endpoint 'A' of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1.4 | ColumnwfFrSwTupleIpAddrB | read-only | obsolete | Instance identfier; indicates the IP address associated with endpoint 'B' of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.3.1.5 | ColumnwfFrSwTupleDlciB | read-only | obsolete | Instance identifier; Indicates the DLCI associated with endpoint 'B' of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.4 | TablewfFrSwMcastTable | not-accessible | mandatory | The list of multicast addresses |
| 1.3.6.1.4.1.18.3.5.9.6.4.1 | RowwfFrSwMcastEntry | not-accessible | mandatory | The parameters for a particular Multicast address. |
| 1.3.6.1.4.1.18.3.5.9.6.4.1.1 | ColumnwfFrSwMcastDelete | read-write | mandatory | Indication to delete this multicast instance. |
| 1.3.6.1.4.1.18.3.5.9.6.4.1.2 | ColumnwfFrSwMcastIndex | read-only | mandatory | Index of this multicast DLCI instance |
| 1.3.6.1.4.1.18.3.5.9.6.4.1.3 | ColumnwfFrSwMcastIpAddr | read-write | mandatory | IP address of the interface in which this multicast DLCI is defined. |
| 1.3.6.1.4.1.18.3.5.9.6.4.1.4 | ColumnwfFrSwMcastDlci | read-write | mandatory | Identifies the multicast DLCI with which the IndividualDlci is associated. |
| 1.3.6.1.4.1.18.3.5.9.6.4.1.5 | ColumnwfFrSwMcastIndividualDlci | read-write | mandatory | Indicates the DLCI associated with the above multicast DLCI. |
| 1.3.6.1.4.1.18.3.5.9.6.5 | NodewfFrSwUsage | |||
| 1.3.6.1.4.1.18.3.5.9.6.5.1 | ScalarwfFrSwUsageEnable | read-write | mandatory | Enable/Disable FRSW billing. |
| 1.3.6.1.4.1.18.3.5.9.6.5.2 | ScalarwfFrSwUsageVolume | read-write | mandatory | Indicates the file system volume number to which the billing usage data files will be written. The volume number corresponds to the slot number on which the vo… |
| 1.3.6.1.4.1.18.3.5.9.6.5.3 | ScalarwfFrSwUsageVolumeBackup | read-write | mandatory | Indicates the backup volume if wfFrSwUsageVolume becomes inoperative. Note: This feature is not implemented in this release. |
| 1.3.6.1.4.1.18.3.5.9.6.5.4 | ScalarwfFrSwUsageDirectory | read-write | mandatory | The name of the directory where the billing usage data files are stored. |
| 1.3.6.1.4.1.18.3.5.9.6.5.5 | ScalarwfFrSwUsageFilePrefix | read-write | mandatory | The base name of billing usage data files. |
| 1.3.6.1.4.1.18.3.5.9.6.5.6 | ScalarwfFrSwUsageTimerInterval | read-write | mandatory | This number determines the timer interval (number of seconds) unit for the Billing process to perform its various timer driven tasks. i.e. updating billing usa… |
| 1.3.6.1.4.1.18.3.5.9.6.5.7 | ScalarwfFrSwUsageUpdateInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the Billing process to collect and update billing usage data in the wfFrSwUsage MIB. Note: When conv… |
| 1.3.6.1.4.1.18.3.5.9.6.5.8 | ScalarwfFrSwUsageStoreInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfFrSwUsage MIB. Note… |
| 1.3.6.1.4.1.18.3.5.9.6.5.9 | ScalarwfFrSwUsageFlushInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfFrSwUsage MIB follo… |
| 1.3.6.1.4.1.18.3.5.9.6.5.10 | ScalarwfFrSwUsageCleanupInterval | read-write | mandatory | This is the interval (number of minutes) for the Billing process to check and delete old billing usage data files. Note: When converted to seconds, this must b… |
| 1.3.6.1.4.1.18.3.5.9.6.5.11 | ScalarwfFrSwUsageLocalTimeZone | read-only | mandatory | Indicates local time zone of the switch |
| 1.3.6.1.4.1.18.3.5.9.6.5.12 | ScalarwfFrSwUsageUpdateTimeStamp | read-only | mandatory | Time stamp of last wfFrSwUsageUpdateInterval timer expiration or the starting time of the current wfFrSwUsageUpdateInterval. This value is number of seconds si… |
| 1.3.6.1.4.1.18.3.5.9.6.5.13 | ScalarwfFrSwUsageStoreTimeStamp | read-only | mandatory | Time stamp of last wfFrSwUsageStoreInterval timer expiration or the starting time of the current wfFrSwUsageStoreInterval. This value is number of seconds sinc… |
| 1.3.6.1.4.1.18.3.5.9.6.5.14 | ScalarwfFrSwUsageFlushTimeStamp | read-only | mandatory | Time stamp of last wfFrSwUsageFlushInterval timer expiration or the starting time of the current wfFrSwUsageFlushInterval. This value is number of seconds sinc… |
| 1.3.6.1.4.1.18.3.5.9.6.5.15 | ScalarwfFrSwUsageCleanupTimeStamp | read-only | mandatory | Time stamp of last wfFrSwUsageCleanupInterval timer expiration or the starting time of the current wfFrSwUsageCleanupInterval. This value is number of seconds … |
| 1.3.6.1.4.1.18.3.5.9.6.5.16 | ScalarwfFrSwUsageUpdateData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating of the billing usage data. Once activated, this attribute should be reset to zero t… |
| 1.3.6.1.4.1.18.3.5.9.6.5.17 | ScalarwfFrSwUsageStoreData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data. Once activated, this attribute should be res… |
| 1.3.6.1.4.1.18.3.5.9.6.5.18 | ScalarwfFrSwUsageFlushData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data and followed by zeroing the wfFrSwBillingUsag… |
| 1.3.6.1.4.1.18.3.5.9.6.5.19 | ScalarwfFrSwUsageFileCleanup | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate checking and deleting old billing usage data files. Once activated, this attribute should be… |
| 1.3.6.1.4.1.18.3.5.9.6.5.20 | ScalarwfFrSwUsageState | read-only | mandatory | current state FRSW billing. |
| 1.3.6.1.4.1.18.3.5.9.6.5.21 | ScalarwfFrSwUsageCurVolume | read-only | mandatory | current file system volume number used. This number is the same as wfFrSwUsageVolume except when the user sets wfFrSwUsageVolume to an invalid number. |
| 1.3.6.1.4.1.18.3.5.9.6.5.22 | ScalarwfFrSwUsageCurVolumeBackup | read-only | mandatory | curent backup file system volume number used. This number is the same as wfFrSwUsageVolumeBackUp except when the user sets wfFrSwUsageVolume to an invalid numb… |
| 1.3.6.1.4.1.18.3.5.9.6.5.23 | ScalarwfFrSwUsageCurDirectory | read-only | mandatory | current directory name used. This number is the same as wfFrSwUsageDirectory except when the user sets wfFrSwUsageDirectory to an invalid name. |
| 1.3.6.1.4.1.18.3.5.9.6.5.24 | ScalarwfFrSwUsageCurFilePrefix | read-only | mandatory | current base file name used. This number is the same as wfFrSwUsageFilePrefix except when the user sets wfFrSwUsageFilePrefix to an invalid name. |
| 1.3.6.1.4.1.18.3.5.9.6.5.25 | ScalarwfFrSwUsageCurTimerInterval | read-only | mandatory | current timer interval number used. This number is the same as wfFrSwUsageTimerInterval except when the user sets wfFrSwUsageTimerInterval to an invalid value. |
| 1.3.6.1.4.1.18.3.5.9.6.5.26 | ScalarwfFrSwUsageCurUpdateInterval | read-only | mandatory | current update interval number used. This number is the same as wfFrSwUsageUpdateInterval except when the user sets wfFrSwUsageUpdateInterval to an invalid val… |
| 1.3.6.1.4.1.18.3.5.9.6.5.27 | ScalarwfFrSwUsageCurStoreInterval | read-only | mandatory | current store timer interval number used. This number is the same as wfFrSwUsageStoreInterval except when the user sets wfFrSwUsageStoreInterval to an invalid … |
| 1.3.6.1.4.1.18.3.5.9.6.5.28 | ScalarwfFrSwUsageCurFlushInterval | read-only | mandatory | current flush timer interval number used. This number is the same as wfFrSwUsageFlushInterval except when the user sets wfFrSwUsageFlushInterval to an invalid … |
| 1.3.6.1.4.1.18.3.5.9.6.5.29 | ScalarwfFrSwUsageCurCleanupInterval | read-only | mandatory | current file cleanup timer interval number used. This number is the same as wfFrSwUsageCleanupInterval except when the user sets wfFrSwUsageCleanupInterval to … |
| 1.3.6.1.4.1.18.3.5.9.6.5.30 | ScalarwfFrSwUsageDebug | read-write | mandatory | Enable/Disable printing of debug edl (trap) messages. NOTE: Do not enable this attribute in operational enviornment as it will likely flood the logging facilit… |
| 1.3.6.1.4.1.18.3.5.9.6.5.31 | ScalarwfFrSwUsageCurDebug | read-only | mandatory | current debug value used. This value is the same as wfFrSwUsageDebug except when the user sets wfFrSwUsageDeubg to an invalid value. |
| 1.3.6.1.4.1.18.3.5.9.6.5.32 | ScalarwfFrSwUsageSwitchId | read-only | mandatory | switch id used in the billing usage data file. |
| 1.3.6.1.4.1.18.3.5.9.6.5.33 | ScalarwfFrSwUsageNumEntries | read-only | mandatory | number of entries in wfFrSwUsageTable |
| 1.3.6.1.4.1.18.3.5.9.6.5.34 | ScalarwfFrSwSvcUsageEnable | read-write | mandatory | Enable/Disable FRSW SVC billing. |
| 1.3.6.1.4.1.18.3.5.9.6.5.35 | ScalarwfFrSwSvcUsageInterimRecordEnable | read-write | mandatory | Enable/Disable Writing FRSW SVC billing record while SVC connection is still up. |
| 1.3.6.1.4.1.18.3.5.9.6.5.36 | ScalarwfFrSwSvcUsageVolume | read-write | mandatory | Indicates the file system volume number to which the SVC billing usage data files will be written. The volume number corresponds to the slot number on which th… |
| 1.3.6.1.4.1.18.3.5.9.6.5.37 | ScalarwfFrSwSvcUsageDirectory | read-write | mandatory | The name of the directory where the SVC billing usage data files are stored. |
| 1.3.6.1.4.1.18.3.5.9.6.5.38 | ScalarwfFrSwSvcUsageFilePrefix | read-write | mandatory | The base name of SVC billing usage data files. |
| 1.3.6.1.4.1.18.3.5.9.6.5.39 | ScalarwfFrSwSvcUsageUpdateInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the SVC Billing process to collect and update billing usage data in the wfFrSwUsage MIB. Note: When … |
| 1.3.6.1.4.1.18.3.5.9.6.5.40 | ScalarwfFrSwSvcUsageStoreInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the SVC Billing process to write billing usage data on to the file system from the wfFrSwUsage MIB. … |
| 1.3.6.1.4.1.18.3.5.9.6.5.41 | ScalarwfFrSwSvcUsageFlushInterval | read-write | mandatory | This number specifies the interval (number of minutes) for the SVC Billing process to write billing usage data on to the file system from the wfFrSwUsage MIB f… |
| 1.3.6.1.4.1.18.3.5.9.6.5.42 | ScalarwfFrSwSvcUsageCleanupInterval | read-write | mandatory | This is the interval (number of minutes) for the SVC Billing process to check and delete old billing usage data files. Note: When converted to seconds, this mu… |
| 1.3.6.1.4.1.18.3.5.9.6.5.43 | ScalarwfFrSwSvcUsageUpdateTimeStamp | read-only | mandatory | Time stamp of last wfFrSwSvcUsageUpdateInterval timer expiration or the starting time of the current wfFrSwSvcUsageUpdateInterval. This value is number of seco… |
| 1.3.6.1.4.1.18.3.5.9.6.5.44 | ScalarwfFrSwSvcUsageStoreTimeStamp | read-only | mandatory | Time stamp of last wfFrSwSvcUsageStoreInterval timer expiration or the starting time of the current wfFrSwSvcUsageStoreInterval. This value is number of second… |
| 1.3.6.1.4.1.18.3.5.9.6.5.45 | ScalarwfFrSwSvcUsageFlushTimeStamp | read-only | mandatory | Time stamp of last wfFrSwSvcUsageFlushInterval timer expiration or the starting time of the current wfFrSwSvcUsageFlushInterval. This value is number of second… |
| 1.3.6.1.4.1.18.3.5.9.6.5.46 | ScalarwfFrSwSvcUsageCleanupTimeStamp | read-only | mandatory | Time stamp of last wfFrSwSvcUsageCleanupInterval timer expiration or the starting time of the current wfFrSwSvcUsageCleanupInterval. This value is number of se… |
| 1.3.6.1.4.1.18.3.5.9.6.5.47 | ScalarwfFrSwSvcUsageUpdateData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating of the SVC billing usage data. Once activated, this attribute should be reset to ze… |
| 1.3.6.1.4.1.18.3.5.9.6.5.48 | ScalarwfFrSwSvcUsageStoreData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating and writing of the SVC billing usage data. Once activated, this attribute should be… |
| 1.3.6.1.4.1.18.3.5.9.6.5.49 | ScalarwfFrSwSvcUsageFlushData | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate updating and writing of the SVC billing usage data and followed by zeroing the wfFrSwBilling… |
| 1.3.6.1.4.1.18.3.5.9.6.5.50 | ScalarwfFrSwSvcUsageFileCleanup | read-write | mandatory | Setting this attribute to a non-zero value will cause an immediate checking and deleting old SVC billing usage data files. Once activated, this attribute shoul… |
| 1.3.6.1.4.1.18.3.5.9.6.5.51 | ScalarwfFrSwSvcUsageState | read-only | mandatory | current state FRSW SVC billing. |
| 1.3.6.1.4.1.18.3.5.9.6.5.52 | ScalarwfFrSwSvcUsageCurVolume | read-only | mandatory | current file system volume number used for SVC Billing. This number is the same as wfFrSwSvcUsageVolume except when the user sets wfFrSwSvcUsageVolume to an in… |
| 1.3.6.1.4.1.18.3.5.9.6.5.53 | ScalarwfFrSwSvcUsageCurDirectory | read-only | mandatory | current directory name used for SVC Billing. This number is the same as wfFrSwSvcUsageDirectory except when the user sets wfFrSwSvcUsageDirectory to an invalid… |
| 1.3.6.1.4.1.18.3.5.9.6.5.54 | ScalarwfFrSwSvcUsageCurFilePrefix | read-only | mandatory | current base file name used for SVC Billing. This name is the same as wfFrSwSvcUsageFilePrefix except when the user sets wfFrSwSvcUsageFilePrefix to an invalid… |
| 1.3.6.1.4.1.18.3.5.9.6.5.55 | ScalarwfFrSwSvcUsageCurUpdateInterval | read-only | mandatory | current update interval number used. This number is the same as wfFrSwSvcUsageUpdateInterval except when the user sets wfFrSwSvcUsageUpdateInterval to an inval… |
| 1.3.6.1.4.1.18.3.5.9.6.5.56 | ScalarwfFrSwSvcUsageCurStoreInterval | read-only | mandatory | current store timer interval number used. This number is the same as wfFrSwSvcUsageStoreInterval except when the user sets wfFrSwSvcUsageStoreInterval to an in… |
| 1.3.6.1.4.1.18.3.5.9.6.5.57 | ScalarwfFrSwSvcUsageCurFlushInterval | read-only | mandatory | current flush timer interval number used. This number is the same as wfFrSwSvcUsageFlushInterval except when the user sets wfFrSwSvcUsageFlushInterval to an in… |
| 1.3.6.1.4.1.18.3.5.9.6.5.58 | ScalarwfFrSwSvcUsageCurCleanupInterval | read-only | mandatory | current file cleanup timer interval number used. This number is the same as wfFrSwSvcUsageCleanupInterval except when the user sets wfFrSwSvcUsageCleanupInterv… |
| 1.3.6.1.4.1.18.3.5.9.6.5.59 | ScalarwfFrSwSvcUsageNumEntries | read-only | mandatory | number of entries in wfFrSwSvcUsageTable |
| 1.3.6.1.4.1.18.3.5.9.6.5.60 | ScalarwfFrSwSvcUsageVersionId | read-only | mandatory | The Software Version ID field is a two byte, right justified, binary formated value that identifies the particular version number of the software release. High… |
| 1.3.6.1.4.1.18.3.5.9.6.5.61 | ScalarwfFrSwUsageSwitchName | read-write | mandatory | The Switch name is a 6-bytes, right justified with leading blanks as necessary. It can be combination of letters, numbers and blanks. This ID identifies the pa… |
| 1.3.6.1.4.1.18.3.5.9.6.5.62 | ScalarwfFrSwPvcUsageFileLayout | read-only | mandatory | PVC usage file layout version |
| 1.3.6.1.4.1.18.3.5.9.6.5.63 | ScalarwfFrSwSvcUsageFileLayout | read-only | mandatory | SVC usage file layout version |
| 1.3.6.1.4.1.18.3.5.9.6.6 | TablewfFrSwUsageTable | not-accessible | obsolete | The Billing usage table. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1 | RowwfFrSwUsageEntry | not-accessible | obsolete | The parameters for Billing Usage. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.1 | ColumnwfFrSwUsageDelete | read-only | obsolete | Indicates status of this entry. FRSW_USAGE_CREATED is the normal case. FRSW_USAGE_DELETED means the corresponding tuple and vc instances were deleted some time… |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.2 | ColumnwfFrSwUsageCircuitNumber | read-only | obsolete | Instance identifier; the circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.3 | ColumnwfFrSwUsageDlci | read-only | obsolete | Instance identifier; this indicates which virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.4 | ColumnwfFrSwUsageIPAddress | read-only | obsolete | (Local) IP address corresponding to wfFrSwUsageCircuitNumber of this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.5 | ColumnwfFrSwUsageStartTimeStampHigh | read-only | obsolete | Time stamp of the starting time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT). |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.6 | ColumnwfFrSwUsageStartTimeStampLow | read-only | obsolete | Time stamp of the starting time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT). |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.7 | ColumnwfFrSwUsageEndTimeStampHigh | read-only | obsolete | Time stamp of the ending time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT). |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.8 | ColumnwfFrSwUsageEndTimeStampLow | read-only | obsolete | Time stamp of the ending time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT). |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.9 | ColumnwfFrSwUsageSentNonDEFramesHigh | read-only | obsolete | Number (the high 32 bits) of local frames sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.10 | ColumnwfFrSwUsageSentNonDEFramesLow | read-only | obsolete | Number (the low 32 bits) of local frames sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.11 | ColumnwfFrSwUsageSentNonDEOctetsHigh | read-only | obsolete | Number (the high 32 bits) of local octets sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.12 | ColumnwfFrSwUsageSentNonDEOctetsLow | read-only | obsolete | Number (the low 32 bits) of local octets sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.13 | ColumnwfFrSwUsageSentDEFramesHigh | read-only | obsolete | Number (the high 32 bits) of local frames with DE bit sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.14 | ColumnwfFrSwUsageSentDEFramesLow | read-only | obsolete | Number (the low 32 bits) of local frames with DE bit sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.15 | ColumnwfFrSwUsageSentDEOctetsHigh | read-only | obsolete | Number (the high 32 bits) of local octets with DE bit sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.16 | ColumnwfFrSwUsageSentDEOctetsLow | read-only | obsolete | Number (the low 32 bits) of local octets with DE bit sent from this virtual circuit between wfFrSwUsageStartTimeStamp and wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.17 | ColumnwfFrSwUsageLastNonDEFramesHigh | read-only | obsolete | The (high 32 bits) value of wfFrSwCctLocalSentNonDEFrames value at wfFrSwUsageEndTimeStamp. Note: Since wfFrSwCctLocalSentNonDEFrames is a 32-bit COUNTER, this… |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.18 | ColumnwfFrSwUsageLastNonDEFramesLow | read-only | obsolete | The (low 32 bits) value of wfFrSwCctLocalSentNonDEFrames value at wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.19 | ColumnwfFrSwUsageLastNonDEOctetsHigh | read-only | obsolete | The (high 32 bits) value of wfFrSwCctLocalSentNonDEOctets value at wfFrSwUsageEndTimeStamp. Note: Since wfFrSwCctLocalSentNonDEOctets is a 32-bit COUNTER, this… |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.20 | ColumnwfFrSwUsageLastNonDEOctetsLow | read-only | obsolete | The (low 32 bits) value of wfFrSwCctLocalSentNonDEOctets value at wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.21 | ColumnwfFrSwUsageLastDEFramesHigh | read-only | obsolete | The (high 32 bits) value of wfFrSwCctLocalSentDEFrames value at wfFrSwUsageEndTimeStamp. Note: Since wfFrSwCctLocalSentNonDEFrames is a 32-bit COUNTER, this is… |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.22 | ColumnwfFrSwUsageLastDEFramesLow | read-only | obsolete | The (low 32 bits) value of wfFrSwCctLocalSentDEFrames value at wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.23 | ColumnwfFrSwUsageLastDEOctetsHigh | read-only | obsolete | The (high 32 bits) value of wfFrSwCctLocalSentDEOctets value at wfFrSwUsageEndTimeStamp. Note: Since wfFrSwCctLocalSentDEOctets is a 32-bit COUNTER, this is re… |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.24 | ColumnwfFrSwUsageLastDEOctetsLow | read-only | obsolete | The (low 32 bits) value of wfFrSwCctLocalSentDEOctets value at wfFrSwUsageEndTimeStamp. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.25 | ColumnwfFrSwUsageRemoteIPAddress | read-only | obsolete | IP address of the other side (remote) of this PVC endpoint. |
| 1.3.6.1.4.1.18.3.5.9.6.6.1.26 | ColumnwfFrSwUsageRemoteDlci | read-only | obsolete | DLCI number of the other side (remote) of this PVC endpoint. |
| 1.3.6.1.4.1.18.3.5.9.6.7 | TablewfFrSwVcTable | not-accessible | mandatory | Frame Relay Virtual Circuit table gives information about a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1 | RowwfFrSwVcEntry | not-accessible | mandatory | An entry in the Frame Relay (Virtual) Circuit table. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.1 | ColumnwfFrSwVcDelete | read-write | mandatory | Indication to delete this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.2 | ColumnwfFrSwVcCircuit | read-only | mandatory | Instance identifier; the circuit number of this interface (logical port). |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.3 | ColumnwfFrSwVcDlci | read-only | mandatory | Instance identifier; this indicates the virtual circuit identifier |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.4 | ColumnwfFrSwVcState | read-only | mandatory | Indicates whether the particular virtual circuit is operational. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.5 | ColumnwfFrSwVcStateSet | read-write | mandatory | User access for setting the state of a virtual circuit |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.6 | ColumnwfFrSwVcMulticast | read-write | mandatory | Indicates whether this dlci is used for multicast or a single destination. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.7 | ColumnwfFrSwVcInBe | read-only | mandatory | Indicates the maximum number Incoming Excess Burst bits that are allowed in a configured time interval (T). |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.8 | ColumnwfFrSwVcOutBe | read-only | mandatory | Indicates the Outgoing Excess Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.9 | ColumnwfFrSwVcInThroughput | read-write | mandatory | Indicates the incoming throughput in bits/sec for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.10 | ColumnwfFrSwVcOutThroughput | read-write | mandatory | Indicates the outgoing throughput in bits/sec for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.11 | ColumnwfFrSwVcOutBc | read-only | mandatory | Indicates the Outgoing Committed Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.12 | ColumnwfFrSwVcInBc | read-only | mandatory | Indicates the Incoming Committed Burst bits for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.13 | ColumnwfFrSwVcInBcOctets | read-only | mandatory | Indicates the Incoming Committed Burst in octets for this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.14 | ColumnwfFrSwVcBecnState | read-only | mandatory | Indicates the BECN state |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.15 | ColumnwfFrSwVcReportedStatus | read-only | mandatory | Record keeping for circuit status |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.16 | ColumnwfFrSwVcReceivedStatus | read-only | mandatory | State of a virtual circuit as reported by the network at an NNI |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.17 | ColumnwfFrSwVcCrossNetStatus | read-only | mandatory | State of a virtual circuit as reported by the other end of the network under bidirectional signalling. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.18 | ColumnwfFrSwVcXNetSent | read-only | mandatory | Whether we have sent a cross net status message for this VC yet. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.19 | ColumnwfFrSwVcXNetReceived | read-only | mandatory | Whether we have received a cross net status message for this VC during the current polling interval. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.20 | ColumnwfFrSwVcCalledIpAddr | read-write | mandatory | Indicates the IP address associated with destination of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.21 | ColumnwfFrSwVcCalledDlci | read-write | mandatory | Indicates the DLCI associated with destination of a virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.22 | ColumnwfFrSwVcTrfPriority | read-write | mandatory | Defines the traffic priority level of all the incoming packets on this VC. FRSW_VCPRIORITY_DEFAULT - Set all incoming user traffic packets to the default prior… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.23 | ColumnwfFrSwVcCreationTime | read-only | mandatory | Indicates the value of sysUpTime when the VC was created. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.24 | ColumnwfFrSwVcLastTimeChange | read-only | mandatory | Indicates the value of sysUpTime when last there was a change in VC state. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.25 | ColumnwfFrSwVcTxNonDeFrames | read-only | mandatory | Indicates the number of frames without the DE bit sent on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.26 | ColumnwfFrSwVcTxNonDeOctets | read-only | mandatory | Indicates the number of octets without DE bit sent on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.27 | ColumnwfFrSwVcTxDeFrames | read-only | mandatory | Indicates the number of frames with DE bit set sent on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.28 | ColumnwfFrSwVcTxDeOctets | read-only | mandatory | Indicates the number of octets with DE bit set sent on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.29 | ColumnwfFrSwVcSetFecnFrames | read-only | mandatory | Indicates the number of frames sent to the interface on which this switch set the FECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.30 | ColumnwfFrSwVcSetFecnOctets | read-only | mandatory | Indicates the number of octets in frames sent to the interface on which this switch set the FECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.31 | ColumnwfFrSwVcSetBecnFrames | read-only | mandatory | Indicates the number of frames sent to the interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.32 | ColumnwfFrSwVcSetBecnOctets | read-only | mandatory | Indicates the number of octets in frames sent to the interface on which this switch set the BECN bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.33 | ColumnwfFrSwVcSetDeFrames | read-only | mandatory | Indicates the number of frames sent to the interface on which this switch set the DE bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.34 | ColumnwfFrSwVcSetDeOctets | read-only | mandatory | Indicates the number of octets in frames sent to the interface on which this switch set the DE bit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.35 | ColumnwfFrSwVcDropNonDeFrames | read-only | mandatory | Indicates the number of frames received over the interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.36 | ColumnwfFrSwVcDropNonDeOctets | read-only | mandatory | Indicates the number of octets in frames received over the interface which were discarded, excluding any frames with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.37 | ColumnwfFrSwVcDropDeFrames | read-only | mandatory | Indicates the number of frames received over the interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.38 | ColumnwfFrSwVcDropDeOctets | read-only | mandatory | Indicates the number of octets in frames received over the interface, having the DE bit set, which were discarded. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.39 | ColumnwfFrSwVcInactiveVcDropFrames | read-only | mandatory | Indicates how many frames were discarded because the virtual circuit was inactive. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.40 | ColumnwfFrSwVcInactiveVcDropOctets | read-only | mandatory | Indicates how many Octets were discarded because the virtual circuit was inactive. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.41 | ColumnwfFrSwVcRecvNonDeFrames | read-only | mandatory | Indicates the number of frames received on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.42 | ColumnwfFrSwVcRecvNonDeOctets | read-only | mandatory | Indicates the number of octets received on this virtual circuit over the interface. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.43 | ColumnwfFrSwVcRecvDeFrames | read-only | mandatory | Indicates the number of frames received over the interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.44 | ColumnwfFrSwVcRecvDeOctets | read-only | mandatory | Indicates the number of octets in frames received over the interface with the DE bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.45 | ColumnwfFrSwVcRecvFecnFrames | read-only | mandatory | Indicates the number of frames received over the interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.46 | ColumnwfFrSwVcRecvFecnOctets | read-only | mandatory | Indicates the number of octets in frames received over the interface with the FECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.47 | ColumnwfFrSwVcRecvBecnFrames | read-only | mandatory | Indicates the number of frames received over the interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.48 | ColumnwfFrSwVcRecvBecnOctets | read-only | mandatory | Indicates the number of octets in frames received over the interface with the BECN bit set. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.49 | ColumnwfFrSwVcRecentNonDeOctets | read-only | mandatory | Indicates the number of octets received over the interface during the most recent sampling period. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.50 | ColumnwfFrSwVcXNetErrors | read-only | mandatory | This is the count of the consecutive errors (usually timeouts) against this VC in cross-network heartbeat polling. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.51 | ColumnwfFrSwVcDropExcessBurstFrames | read-only | mandatory | Indicates the number of Excess Burst Frames dropped on this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.52 | ColumnwfFrSwVcDropExcessBurstOctets | read-only | mandatory | Indicates the number of Excess Burst Octets dropped on this virtual circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.53 | ColumnwfFrSwVcInBeOctets | read-only | mandatory | Indicates the maximum number Incoming Excess Burst bytes that are allowed in a configured time interval (T). |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.54 | ColumnwfFrSwVcCfgInBe | read-write | mandatory | The number of Excess Burst in bits |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.55 | ColumnwfFrSwVcRedirectAction | read-write | mandatory | Perform pvc source redirect manually or based on cross-net updates: 'redirecttoprimary(2)' will force to switch to primary; 'redirecttobackup(3)' will force to… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.56 | ColumnwfFrSwVcRedirectType | read-write | mandatory | Type of dte notification at switching time: 'transparent(1)' will not send notification to dte; 'intrusiven(2)' will send async update with NEW bit; 'intrusive… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.57 | ColumnwfFrSwVcRedirectState | read-only | mandatory | PVC Source Redirect State: 'backupinactive(1)' - backup is not configured and/or cross-net status is inactive; will allow traffic only through primary. 'primar… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.58 | ColumnwfFrSwVcBackupCalledIpAddr | read-write | mandatory | Backup Called Ip Address of the remote end of the PVC. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.59 | ColumnwfFrSwVcBackupCalledDlci | read-write | mandatory | Backup Called Dlci of the remote end of the PVC. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.60 | ColumnwfFrSwVcBackupCrossNetStatus | read-only | mandatory | Cross net status of the backup remote end of the PVC. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.61 | ColumnwfFrSwVcBackupCrossNetErrors | read-only | mandatory | Support counter of missed cross net update from backup remote end of the PVC, range: [0, wfFrSwDlcmiCrossNetErrorThreshold]. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.62 | ColumnwfFrSwVcAtmIwfMode | read-write | mandatory | This attribute indicates the mode of FR-ATM interworking over this FR PVC or that FR-ATM interworking is not enabled on it. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.63 | ColumnwfFrSwVcAtmIwfVPI | read-write | mandatory | This is relevant only when the ATM/FR interworking is enabled for this PVC. This indicates the ATM virtual path identifier associated with the Frame Relay PVC … |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.64 | ColumnwfFrSwVcAtmIwfVCI | read-write | mandatory | This is relevant only when FR/ATM interworking is enabled for this PVC. This indicates the ATM virtual circuit identifier associated with the Frame Relay PVC d… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.65 | ColumnwfFrSwVcAtmIwfLossPriorityPolicy | read-write | mandatory | This is relevant only when FR/ATM interworking is enabled for this FR PVC. This indicates the policy for translating ATM CLP to FR DE on this PVC or simply set… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.66 | ColumnwfFrSwVcAtmIwfDePolicy | read-write | mandatory | This is relevant only when FR/ATM interworking is enabled for this FR PVC. This indicates the policy on this PVC for translating FR DE to ATM CLP or simply set… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.67 | ColumnwfFrSwVcAtmIwfEfciPolicy | read-write | mandatory | This is relevant only when FR/ATM interworking is enabled for this FR PVC. This indicates the policy on this PVC for translating FR FECN to ATM EFCI or simply … |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.68 | ColumnwfFrSwVcEscapeEnable | read-write | mandatory | Identifies this PVC as either a standard FRSW PVC (escape disabled) or an Escape PVC (escape enabled). The type of Escape PVC (ingress node or egress node) is … |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.69 | ColumnwfFrSwVcSpvcCallState | read-only | mandatory | Indicates to the state of the SPVC call for this DLCI. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.70 | ColumnwfFrSwVcCallReqCalledAddr | read-write | mandatory | Called E.164/X.121 Address for an SPVC Call Request Agent. The address type is determined by the wfFrSwDlcmiL2AddrType attribute in wfFrSwDlcmiEntry. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.71 | ColumnwfFrSwVcCallReqDlciSelectionType | read-write | mandatory | Indicates to the Calling End of an SPVC Call Request whether to use any available DLCI, or a specific DLCI. If 'specific' is chosen, the called DLCI value is s… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.72 | ColumnwfFrSwVcCallReqCalledDlci | read-write | mandatory | Indicates to the Calling End of an SPVC Call Request the DLCI to be used at the destination of a virtual circuit. This value should be specified when 'specific… |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.73 | ColumnwfFrSwVcCallReqRetryTimer | read-write | mandatory | Indicates the number of minutes the Call Request Agent should wait for an SPVC CONNECT message before declaring a Call Setup request REJECTED. |
| 1.3.6.1.4.1.18.3.5.9.6.7.1.74 | ColumnwfFrSwVcCallReqMaxRetries | read-write | mandatory | Indicates the number of times the Call Request Agent should retry failed Call Setup requests before declaring the SPVC invalid. |
| 1.3.6.1.4.1.18.3.5.9.6.8 | TablewfFrSwIsdnBaseTable | not-accessible | mandatory | This is a FRSW over ISDN configuration table. This table specifies whether the Calling Party (ANI) or Called Party (DNIS) ISDN Phone Number should be used to m… |
| 1.3.6.1.4.1.18.3.5.9.6.8.1 | RowwfFrSwIsdnBaseEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.8.1.1 | ColumnwfFrSwIsdnBaseDelete | read-write | mandatory | Indication to delete this FRSW ISDN interface. |
| 1.3.6.1.4.1.18.3.5.9.6.8.1.2 | ColumnwfFrSwIsdnBaseSlotNum | read-only | mandatory | This number is the Slot Number for the PRI interface(s) that are being configured for FRSW ISDN. There will be one of these tables for every slot where an FRSW… |
| 1.3.6.1.4.1.18.3.5.9.6.8.1.3 | ColumnwfFrSwIsdnBaseAssocType | read-write | mandatory | Indicates which ISDN Phone Number (ANI or DNIS) to use to do the ISDN call to FRSW UNI mapping. |
| 1.3.6.1.4.1.18.3.5.9.6.9 | TablewfFrSwIsdnAssocTable | not-accessible | mandatory | This table defines the Association Table to be used for the FRSW over ISDN application. The table contains a list of ISDN Phone Numbers and the associated FRSW… |
| 1.3.6.1.4.1.18.3.5.9.6.9.1 | RowwfFrSwIsdnAssocEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.9.1.1 | ColumnwfFrSwIsdnAssocDelete | read-write | mandatory | Indication to delete this Association Instance. |
| 1.3.6.1.4.1.18.3.5.9.6.9.1.2 | ColumnwfFrSwIsdnAssocSlotNum | read-only | mandatory | Slot with which this ISDN Phone Number is associated. |
| 1.3.6.1.4.1.18.3.5.9.6.9.1.3 | ColumnwfFrSwIsdnAssocNum | read-only | mandatory | ISDN Phone Number that is used to look up the appropriate FRSW UNI Index. This number is compared with either the Calling Party Number (ANI) Information Elemen… |
| 1.3.6.1.4.1.18.3.5.9.6.9.1.4 | ColumnwfFrSwIsdnAssocScrnEnable | read-write | mandatory | Indicate whether allowed screening should be enabled or disabled for all of the UNIs contained in the FRSW UNI Index. |
| 1.3.6.1.4.1.18.3.5.9.6.9.1.5 | ColumnwfFrSwIsdnAssocIndex | read-write | mandatory | A number that indicates the FRSW UNI Index that is is associated with the ISDN Phone Number. This FRSW UNI Index is used as a key to obtain the UNIs and the Sc… |
| 1.3.6.1.4.1.18.3.5.9.6.10 | TablewfFrSwIsdnUniTable | not-accessible | mandatory | This table is used by the FRSW over ISDN application. The table defines a list of FRSW UNIs that are to be collected into a hunt group identifiable by an Index… |
| 1.3.6.1.4.1.18.3.5.9.6.10.1 | RowwfFrSwIsdnUniEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.10.1.1 | ColumnwfFrSwIsdnUniDelete | read-write | mandatory | Indication to delete this FRSW UNI Index Instance. |
| 1.3.6.1.4.1.18.3.5.9.6.10.1.2 | ColumnwfFrSwIsdnUniIndex | read-only | mandatory | FRSW UNI Index a group of related FRSW UNIs that are collected together as a hunt group. This number ties this entry to an entry in wfFrSwIsdnAssocEntry. |
| 1.3.6.1.4.1.18.3.5.9.6.10.1.3 | ColumnwfFrSwIsdnUniNum | read-only | mandatory | A FRSW UNI/Circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.10.1.4 | ColumnwfFrSwIsdnUniState | read-only | mandatory | State of this UNI (available or in-use). |
| 1.3.6.1.4.1.18.3.5.9.6.11 | TablewfFrSwIsdnScrnTable | not-accessible | mandatory | This is the incoming call screening table for the FRSW over ISDN application. The table consists of a FRSW UNI Index and a list of allowable ISDN Phone numbers… |
| 1.3.6.1.4.1.18.3.5.9.6.11.1 | RowwfFrSwIsdnScrnEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.11.1.1 | ColumnwfFrSwIsdnScrnDelete | read-write | mandatory | Indication to delete this Scrn Instance. |
| 1.3.6.1.4.1.18.3.5.9.6.11.1.2 | ColumnwfFrSwIsdnScrnIndex | read-only | mandatory | FRSW UNI Index - A number that ties this entry to an entry in wfFrSwIsdnAssocEntry. |
| 1.3.6.1.4.1.18.3.5.9.6.11.1.3 | ColumnwfFrSwIsdnScrnNum | read-only | mandatory | ISDN Phone Number of a user authorized to access the UNIs contained in the FRSW UNI Index. |
| 1.3.6.1.4.1.18.3.5.9.6.12 | TablewfFrSwSigTable | not-accessible | mandatory | The Frame relay signalling table contains frame relay signalling entries indexed by the frame relay access channel circuit number. An instance of wfFrSwSigEntr… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1 | RowwfFrSwSigEntry | not-accessible | mandatory | An entry in the Frame Relay signalling port information table. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.1 | ColumnwfFrSwSigDelete | read-write | mandatory | Indication to delete this instance |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.2 | ColumnwfFrSwSigCircuit | read-only | mandatory | The circuit number for this frame relay access channel |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.3 | ColumnwfFrSwSigSvcDlciLow | read-write | mandatory | Lowest DLCI to be used for SVC, the default value is for 2 octet frame header |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.4 | ColumnwfFrSwSigSvcDlciHigh | read-write | mandatory | Highest DLCI to be used for SVC, the default value is for 2 octet frame header. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.5 | ColumnwfFrSwSigDlciAssign | read-write | mandatory | Determines if DLCI's are assigned starting at wfFrSwSigSvcDlciHigh and working towards wfFrSwSigSvcDlciLow or vice versa. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.6 | ColumnwfFrSwSigMaxNumOfSvcs | read-write | mandatory | Indicates the maximum number of simultaneous switched virtual circuits allowed on the logical line. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.7 | ColumnwfFrSwSigNumOfSvcsInUse | read-only | mandatory | Indicates the number of switched virtual circuits in use on the logical line. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.8 | ColumnwfFrSwSigDefaultThroughput | read-write | mandatory | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing throughput fields when they are not included in the setup message by… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.9 | ColumnwfFrSwSigDefaultMinAcceptThroughput | read-write | mandatory | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing minimum acceptable throughput fields when they are not included in t… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.10 | ColumnwfFrSwSigDefaultBc | read-only | mandatory | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing Bc fields when they are not included in the setup message by the use… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.11 | ColumnwfFrSwSigDefaultBe | read-write | mandatory | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing Be fields when they are not included in the setup message by the use… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.12 | ColumnwfFrSwSigMaxInThroughputPerSvc | read-write | mandatory | This is the maximum incoming throughput that any single SVC may negotiate for a call. Calls requesting in excess of this attribute are rejected. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.13 | ColumnwfFrSwSigMaxOutThroughputPerSvc | read-write | mandatory | This is the maximum outgoing throughput that any single SVC may negotiate for a call. Calls requesting in excess of this attribute are rejected. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.14 | ColumnwfFrSwSigTotalInNegotiableThroughput | read-write | mandatory | This is the total maximum incoming throughput that is available for all frame mode calls on the port. If the sum of the incoming throughput requested by a call… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.15 | ColumnwfFrSwSigTotalInCurrentThroughput | read-only | mandatory | This is the total incoming throughput that has been negotiated for use by all SVC's on the port. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.16 | ColumnwfFrSwSigTotalOutNegotiableThroughput | read-write | mandatory | This is the total maximum outgoing throughput that is available for all frame mode calls on the port. If the sum of the outgoing throughput requested by a call… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.17 | ColumnwfFrSwSigTotalOutCurrentThroughput | read-only | mandatory | This is the total incoming throughput that has been negotiated for use by all SVC's on the port. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.18 | ColumnwfFrSwSigXNetClearingDisable | read-write | mandatory | If cross-net polling (wfFrSwDlcmiCrossNetEnable) is enabled on this interface, and the error threshold (wfFrSwDlcmiCrossNetErrorThreshold) is exceeded, the net… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.19 | ColumnwfFrSwSigCallingPartyIEMandatory | read-write | mandatory | Reject the call if the Calling Party IE is absent in the setup message or if the provided Calling Party IE fails address authentication tests againt the config… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.20 | ColumnwfFrSwSigT301 | read-write | mandatory | Timer number: T301 default time-out: 3 min state of call: call initiated cause for start: incoming setup normal stop: outgoing connect at the first expiry: cle… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.21 | ColumnwfFrSwSigT303 | read-write | mandatory | Timer number: T303 default time-out: 4 s state of call: call present cause for start: outgoing setup normal stop: incoming connect/call-proceeding/ release-com… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.22 | ColumnwfFrSwSigT305 | read-write | mandatory | Timer number: T305 default time-out: 30 s state of call: disconnect ind cause for start: outgoing disconnect normal stop: incoming release/disconnect at the fi… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.23 | ColumnwfFrSwSigT308 | read-write | mandatory | Timer number: T308 default time-out: 4 s state of call: release req cause for start: outgoing release normal stop: incoming release/release-complete at the fir… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.24 | ColumnwfFrSwSigT310 | read-write | mandatory | Timer number: T310 default time-out: 10 s state of call: incoming call proceeding cause for start: incoming call proceeding normal stop: incoming connect/disco… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.25 | ColumnwfFrSwSigT322 | read-write | mandatory | Timer number: T322 default time-out: 4 s state of call: any call state cause for start: outgoing status enquiry normal stop: incoming status/disconnect/ releas… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.26 | ColumnwfFrSwSigInSetupPkts | read-only | mandatory | number of incoming setup packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.27 | ColumnwfFrSwSigInCallProceedingPkts | read-only | mandatory | number of incoming call proceeding packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.28 | ColumnwfFrSwSigInConnectPkts | read-only | mandatory | number of incoming connect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.29 | ColumnwfFrSwSigInDisconnectPkts | read-only | mandatory | number of incoming disconnect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.30 | ColumnwfFrSwSigInReleasePkts | read-only | mandatory | number of incoming release packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.31 | ColumnwfFrSwSigInReleaseCompletePkts | read-only | mandatory | number of incoming release complete packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.32 | ColumnwfFrSwSigInStatusEnquiryPkts | read-only | mandatory | number of incoming status enquiry packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.33 | ColumnwfFrSwSigInStatusPkts | read-only | mandatory | number of incoming status packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.34 | ColumnwfFrSwSigInUnknownPkts | read-only | mandatory | number of incoming unknown packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.35 | ColumnwfFrSwSigOutSetupPkts | read-only | mandatory | number of outgoing setup packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.36 | ColumnwfFrSwSigOutCallProceedingPkts | read-only | mandatory | number of outgoing call proceeding packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.37 | ColumnwfFrSwSigOutConnectPkts | read-only | mandatory | number of outgoing connect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.38 | ColumnwfFrSwSigOutDisconnectPkts | read-only | mandatory | number of outgoing disconnect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.39 | ColumnwfFrSwSigOutReleasePkts | read-only | mandatory | number of outgoing release packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.40 | ColumnwfFrSwSigOutReleaseCompletePkts | read-only | mandatory | number of outgoing release packest |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.41 | ColumnwfFrSwSigOutStatusEnquiryPkts | read-only | mandatory | number of outgoing status enquiry packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.42 | ColumnwfFrSwSigOutStatusPkts | read-only | mandatory | number of outgoing status packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.43 | ColumnwfFrSwSigRejectedConnRequests | read-only | mandatory | number of connections rejected |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.44 | ColumnwfFrSwSigNwrkAbortedConnections | read-only | mandatory | number of connections aborted by network |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.45 | ColumnwfFrSwSigL2Resets | read-only | mandatory | number of L2 resets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.46 | ColumnwfFrSwSigDlciIEAllowed | read-write | mandatory | Reject the call if the Dlci IE is present in the setup message and wfFrSwSigDlciIEAllowed is set to disabled. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.47 | ColumnwfFrSwSigX213PriorityIEAllowed | read-write | mandatory | Reject the call if the X213 Priority IE is present in setup message and wfFrSwSigX213PriorityIEAllowed is set to disabled. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.48 | ColumnwfFrSwSigMaximumBe | read-write | mandatory | This value is the maximum allowed Be for a SVC connection |
| 1.3.6.1.4.1.18.3.5.9.6.13 | TablewfFrSwGlobalE164AddrTable | not-accessible | mandatory | wfFrSwGlobalE164AddrTable is used by Directory Services to translate a range of E.164 addresses into an internal IP network address. E.164 ranges must not ever… |
| 1.3.6.1.4.1.18.3.5.9.6.13.1 | RowwfFrSwGlobalE164AddrEntry | not-accessible | mandatory | An entry in the Frame Relay Global E.164 Address Table. |
| 1.3.6.1.4.1.18.3.5.9.6.13.1.1 | ColumnwfFrSwGlobalE164AddrDelete | read-write | mandatory | Indication to delete/create this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.13.1.2 | ColumnwfFrSwGlobalE164AddrLow | read-only | mandatory | Instance identifier; the low end of the E.164 address range. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as n… |
| 1.3.6.1.4.1.18.3.5.9.6.13.1.3 | ColumnwfFrSwGlobalE164AddrHigh | read-only | mandatory | Instance identifier; the high end of the E.164 address range. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as … |
| 1.3.6.1.4.1.18.3.5.9.6.13.1.4 | ColumnwfFrSwGlobalE164AddrIPAddr | read-write | mandatory | This is the internal IP network address associated with this range of E.164 addresses. |
| 1.3.6.1.4.1.18.3.5.9.6.14 | TablewfFrSwGlobalX121AddrTable | not-accessible | mandatory | wfFrSwGlobalX121AddrTable is used by Directory Services to translate a range of X.121 addresses into an internal IP network address. X.121 ranges must not ever… |
| 1.3.6.1.4.1.18.3.5.9.6.14.1 | RowwfFrSwGlobalX121AddrEntry | not-accessible | mandatory | An entry in the Frame Relay Global X.121 Address Table. |
| 1.3.6.1.4.1.18.3.5.9.6.14.1.1 | ColumnwfFrSwGlobalX121AddrDelete | read-write | mandatory | Indication to delete/create this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.14.1.2 | ColumnwfFrSwGlobalX121AddrLow | read-only | mandatory | Instance identifier; the low end of the X.121 address range. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as n… |
| 1.3.6.1.4.1.18.3.5.9.6.14.1.3 | ColumnwfFrSwGlobalX121AddrHigh | read-only | mandatory | Instance identifier; the high end of the X.121 address range. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as … |
| 1.3.6.1.4.1.18.3.5.9.6.14.1.4 | ColumnwfFrSwGlobalX121AddrIPAddr | read-write | mandatory | This is the internal IP network address associated with this range of X.121 addresses. |
| 1.3.6.1.4.1.18.3.5.9.6.15 | TablewfFrSwLocalE164AddrTable | not-accessible | mandatory | wfFrSwLocalE164AddrTable contains E.164 addresses on the local BNX and CUG (Closed User Group) related information. |
| 1.3.6.1.4.1.18.3.5.9.6.15.1 | RowwfFrSwLocalE164AddrEntry | not-accessible | mandatory | An entry in the Frame Relay Local E.164 Address Table. |
| 1.3.6.1.4.1.18.3.5.9.6.15.1.1 | ColumnwfFrSwLocalE164AddrDelete | read-write | mandatory | Indication to delete/create this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.15.1.2 | ColumnwfFrSwLocalE164AddrCct | read-only | mandatory | Instance identifier; internal CCT number associated with this E.164 address. |
| 1.3.6.1.4.1.18.3.5.9.6.15.1.3 | ColumnwfFrSwLocalE164Address | read-only | mandatory | Instance identifier; an E.164 address. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as necessary. |
| 1.3.6.1.4.1.18.3.5.9.6.15.1.4 | ColumnwfFrSwLocalE164AddrCUG | read-write | mandatory | CUG (Closed User Group) information. The structure of the CUG information consists zero or more groups (number of groups can be derived from the OCTET STRING d… |
| 1.3.6.1.4.1.18.3.5.9.6.15.1.5 | ColumnwfFrSwLocalE164AddrLocalFlag | read-write | mandatory | Local/Non-Local Identifier Flag. Used for SPVCs. |
| 1.3.6.1.4.1.18.3.5.9.6.16 | TablewfFrSwLocalX121AddrTable | not-accessible | mandatory | wfFrSwLocalX121AddrTable contains X.121 addresses on the local BNX and CUG (Closed User Group) related information. |
| 1.3.6.1.4.1.18.3.5.9.6.16.1 | RowwfFrSwLocalX121AddrEntry | not-accessible | mandatory | An entry in the Frame Relay Local X.121 Address Table. |
| 1.3.6.1.4.1.18.3.5.9.6.16.1.1 | ColumnwfFrSwLocalX121AddrDelete | read-write | mandatory | Indication to delete/create this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.16.1.2 | ColumnwfFrSwLocalX121AddrCct | read-only | mandatory | Instance identifier; internal CCT number associated with this X.121 address. |
| 1.3.6.1.4.1.18.3.5.9.6.16.1.3 | ColumnwfFrSwLocalX121Address | read-only | mandatory | Instance identifier; a X.121 address. This is an 8-byte fixed length octet string format, right justified with padded leading zeros as necessary. |
| 1.3.6.1.4.1.18.3.5.9.6.16.1.4 | ColumnwfFrSwLocalX121AddrCUG | read-write | mandatory | CUG (Closed User Group) information. The structure of the CUG information consists zero or more groups (number of groups can be derived from the OCTET STRING d… |
| 1.3.6.1.4.1.18.3.5.9.6.16.1.5 | ColumnwfFrSwLocalX121AddrLocalFlag | read-write | mandatory | Local/Non-Local Identifier Flag. Used for SPVCs. |
| 1.3.6.1.4.1.18.3.5.9.6.17 | NodewfFrSwBase | |||
| 1.3.6.1.4.1.18.3.5.9.6.17.1 | ScalarwfFrSwBaseDelete | read-write | mandatory | Indication to delete/create this base group |
| 1.3.6.1.4.1.18.3.5.9.6.17.2 | ScalarwfFrSwBaseIpAddr | read-write | mandatory | Indicates this BNX's (circuit-less) IP address |
| 1.3.6.1.4.1.18.3.5.9.6.17.3 | ScalarwfFrSwBaseShutDown | read-write | mandatory | Bit mask for slots to shutdown, slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth. |
| 1.3.6.1.4.1.18.3.5.9.6.18 | TablewfFrSwCngcMonTable | not-accessible | mandatory | This table is used by FRSW Congestion Control application. The table is used to Monitor the congestion level of a particular circuit. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1 | RowwfFrSwCngcMonEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.1 | ColumnwfFrSwCngcMonReset | read-write | mandatory | Indication to reset Cngc Monitor Counters. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.2 | ColumnwfFrSwCngcMonCct | read-only | mandatory | Circuit to be monitored. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.3 | ColumnwfFrSwCngcMonP0Level1Percent | read-only | mandatory | Percentage of time congestion is at level 1. for Priority 0 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.4 | ColumnwfFrSwCngcMonP0Level2Percent | read-only | mandatory | Percentage of time congestion is at level 2. for Priority 0 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.5 | ColumnwfFrSwCngcMonP0Level3Percent | read-only | mandatory | Percentage of time congestion is at level 3. for Priority 0 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.6 | ColumnwfFrSwCngcMonP0Level4Percent | read-only | mandatory | Percentage of time congestion is at level 4. for Priority 0 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.7 | ColumnwfFrSwCngcMonP1Level1Percent | read-only | mandatory | Percentage of time congestion is at level 1. for Priority 1 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.8 | ColumnwfFrSwCngcMonP1Level2Percent | read-only | mandatory | Percentage of time congestion is at level 2. for Priority 1 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.9 | ColumnwfFrSwCngcMonP1Level3Percent | read-only | mandatory | Percentage of time congestion is at level 3. for Priority 1 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.10 | ColumnwfFrSwCngcMonP1Level4Percent | read-only | mandatory | Percentage of time congestion is at level 4. for Priority 1 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.11 | ColumnwfFrSwCngcMonP2Level1Percent | read-only | mandatory | Percentage of time congestion is at level 1. for Priority 2 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.12 | ColumnwfFrSwCngcMonP2Level2Percent | read-only | mandatory | Percentage of time congestion is at level 2. for Priority 2 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.13 | ColumnwfFrSwCngcMonP2Level3Percent | read-only | mandatory | Percentage of time congestion is at level 3. for Priority 2 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.14 | ColumnwfFrSwCngcMonP2Level4Percent | read-only | mandatory | Percentage of time congestion is at level 4. for Priority 2 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.15 | ColumnwfFrSwCngcMonP3Level1Percent | read-only | mandatory | Percentage of time congestion is at level 1. for Priority 3 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.16 | ColumnwfFrSwCngcMonP3Level2Percent | read-only | mandatory | Percentage of time congestion is at level 2. for Priority 3 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.17 | ColumnwfFrSwCngcMonP3Level3Percent | read-only | mandatory | Percentage of time congestion is at level 3. for Priority 3 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.18.1.18 | ColumnwfFrSwCngcMonP3Level4Percent | read-only | mandatory | Percentage of time congestion is at level 4. for Priority 3 Traffic. |
| 1.3.6.1.4.1.18.3.5.9.6.19 | TablewfFrSwVirtualIntfTable | not-accessible | mandatory | The table is used to create 'virtual' FRSW access lines. |
| 1.3.6.1.4.1.18.3.5.9.6.19.1 | RowwfFrSwVirtualIntfEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.19.1.1 | ColumnwfFrSwVirtualIntfDelete | read-write | mandatory | Indication to delete this virtual interface. |
| 1.3.6.1.4.1.18.3.5.9.6.19.1.2 | ColumnwfFrSwVirtualIntfSlot | read-only | mandatory | Instance identifier; the slot number of this interface. |
| 1.3.6.1.4.1.18.3.5.9.6.19.1.3 | ColumnwfFrSwVirtualIntfCct | read-only | mandatory | Instance identifier; the circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.9.6.19.1.4 | ColumnwfFrSwVirtualIntfLineNum | read-only | mandatory | Line number for this virtual interface. |
| 1.3.6.1.4.1.18.3.5.9.6.20 | TablewfFrSwExtFileSysTable | not-accessible | mandatory | This table is used by FRSW to extend the file system to DRAM device. |
| 1.3.6.1.4.1.18.3.5.9.6.20.1 | RowwfFrSwExtFileSysEntry | not-accessible | mandatory | Instance Id for this table. |
| 1.3.6.1.4.1.18.3.5.9.6.20.1.1 | ColumnwfFrSwExtFileSysDelete | read-write | mandatory | Indication to delete/create this entry. |
| 1.3.6.1.4.1.18.3.5.9.6.20.1.2 | ColumnwfFrSwExtFileSysSlot | read-only | mandatory | A unique value for each slot. Its value ranges between 1 and 14. |
| 1.3.6.1.4.1.18.3.5.9.6.20.1.3 | ColumnwfFrSwExtFileSysSize | read-write | mandatory | The memory size of the extended file system in byte unit. The value zero also means that extended file system is disabled. Non-zero value means enabled. Its su… |
| 1.3.6.1.4.1.18.3.5.9.6.20.1.4 | ColumnwfFrSwExtFileSysActualSize | read-only | mandatory | The actual memory size the system allocated. |
| 1.3.6.1.4.1.18.3.5.9.6.20.1.5 | ColumnwfFrSwExtFileSysState | read-only | mandatory | The status of the extended file system. State up indicates that the requested memory size for the extended file system has been allocated successfully and the … |