Wellfleet-SYNC-MIB
128 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.5 | TablewfSyncTable | not-accessible | mandatory | SYNC line record |
| 1.3.6.1.4.1.18.3.4.5.1 | RowwfSyncEntry | not-accessible | mandatory | An entry in the SYNC table |
| 1.3.6.1.4.1.18.3.4.5.1.1 | ColumnwfSyncDelete | read-write | mandatory | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.5.1.2 | ColumnwfSyncDisable | read-write | mandatory | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.5.1.3 | ColumnwfSyncState | read-only | mandatory | Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced with NOTPRES. |
| 1.3.6.1.4.1.18.3.4.5.1.4 | ColumnwfSyncSlot | read-only | mandatory | Instance ID Slot, filled in by driver |
| 1.3.6.1.4.1.18.3.4.5.1.5 | ColumnwfSyncConnector | read-only | mandatory | Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connector'. Where 'module' is defined… |
| 1.3.6.1.4.1.18.3.4.5.1.6 | ColumnwfSyncCct | read-write | mandatory | CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.7 | ColumnwfSyncBofl | read-write | mandatory | breath of life parameter |
| 1.3.6.1.4.1.18.3.4.5.1.8 | ColumnwfSyncBoflTmo | read-write | mandatory | breath of life timeout in seconds |
| 1.3.6.1.4.1.18.3.4.5.1.9 | ColumnwfSyncMtu | read-write | mandatory | MTU parameter, this is buffer size for SYNC media, fixed |
| 1.3.6.1.4.1.18.3.4.5.1.10 | ColumnwfSyncMadr | read-only | mandatory | Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector. |
| 1.3.6.1.4.1.18.3.4.5.1.11 | ColumnwfSyncPromiscuous | read-write | mandatory | The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only fram… |
| 1.3.6.1.4.1.18.3.4.5.1.12 | ColumnwfSyncXid | read-write | mandatory | XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames. |
| 1.3.6.1.4.1.18.3.4.5.1.13 | ColumnwfSyncClkSource | read-write | mandatory | Tx/Rx clock source is either internally or external generated. |
| 1.3.6.1.4.1.18.3.4.5.1.14 | ColumnwfSyncClkSpeed | read-write | mandatory | Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected. |
| 1.3.6.1.4.1.18.3.4.5.1.15 | ColumnwfSyncSignalMode | read-write | mandatory | The signal mode parameter indicates the line paramter balanced or unbalanced. |
| 1.3.6.1.4.1.18.3.4.5.1.16 | ColumnwfSyncRtsEnable | read-write | mandatory | Note: In KG84 support, RTS has a different meaning |
| 1.3.6.1.4.1.18.3.4.5.1.17 | ColumnwfSyncBurstCount | read-write | mandatory | Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. The default is always 8 short wor… |
| 1.3.6.1.4.1.18.3.4.5.1.18 | ColumnwfSyncService | read-write | mandatory | Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the L… |
| 1.3.6.1.4.1.18.3.4.5.1.19 | ColumnwfSyncRetryCount | read-write | mandatory | The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count… |
| 1.3.6.1.4.1.18.3.4.5.1.20 | ColumnwfSyncLinkIdleTimer | read-write | mandatory | The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed i… |
| 1.3.6.1.4.1.18.3.4.5.1.21 | ColumnwfSyncRetryTimer | read-write | mandatory | The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control frames are sent at the expiration o… |
| 1.3.6.1.4.1.18.3.4.5.1.22 | ColumnwfSyncExtendedAddress | read-write | mandatory | This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine th… |
| 1.3.6.1.4.1.18.3.4.5.1.23 | ColumnwfSyncExtendedAddressForce | read-write | mandatory | When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. … |
| 1.3.6.1.4.1.18.3.4.5.1.24 | ColumnwfSyncExtendedControl | read-write | mandatory | This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead … |
| 1.3.6.1.4.1.18.3.4.5.1.25 | ColumnwfSyncExtendedControlForce | read-write | mandatory | This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Tr… |
| 1.3.6.1.4.1.18.3.4.5.1.26 | ColumnwfSyncConnectAttempts | read-write | mandatory | This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 se… |
| 1.3.6.1.4.1.18.3.4.5.1.27 | ColumnwfSyncWindowSizeTx | read-write | mandatory | The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.28 | ColumnwfSyncWindowSizeTxExtc | read-write | mandatory | The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.29 | ColumnwfSyncMinFrameSpace | read-write | mandatory | The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames. |
| 1.3.6.1.4.1.18.3.4.5.1.30 | ColumnwfSyncLocalAddress | read-write | mandatory | The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. |
| 1.3.6.1.4.1.18.3.4.5.1.31 | ColumnwfSyncRemoteAddress | read-write | mandatory | The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. |
| 1.3.6.1.4.1.18.3.4.5.1.32 | ColumnwfSyncPassThruLocalMadr | read-write | mandatory | 48 bit MAC address of Local end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.33 | ColumnwfSyncPassThruRemoteMadr | read-write | mandatory | 48 bit MAC address of Remote end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.34 | ColumnwfSyncWanProtocol | read-write | mandatory | WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. |
| 1.3.6.1.4.1.18.3.4.5.1.35 | ColumnwfSyncCrcSize | read-write | mandatory | CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC |
| 1.3.6.1.4.1.18.3.4.5.1.36 | ColumnwfSyncRxOctets | read-only | mandatory | Number of octets received without error |
| 1.3.6.1.4.1.18.3.4.5.1.37 | ColumnwfSyncRxFrames | read-only | mandatory | Number of frames received without error |
| 1.3.6.1.4.1.18.3.4.5.1.38 | ColumnwfSyncTxOctets | read-only | mandatory | Number of octets transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.39 | ColumnwfSyncTxFrames | read-only | mandatory | Number of frames transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.40 | ColumnwfSyncRxErrors | read-only | mandatory | Number of receive errors |
| 1.3.6.1.4.1.18.3.4.5.1.41 | ColumnwfSyncTxErrors | read-only | mandatory | Number of transmission errors |
| 1.3.6.1.4.1.18.3.4.5.1.42 | ColumnwfSyncLackRescRx | read-only | mandatory | Number of Rx frames dropped due to lack of buffer resources |
| 1.3.6.1.4.1.18.3.4.5.1.43 | ColumnwfSyncLackRescTx | read-only | mandatory | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| 1.3.6.1.4.1.18.3.4.5.1.44 | ColumnwfSyncUnderFlowTx | read-only | mandatory | Number of transmission underflows, device FIFO went empty before next DMA request was granted. |
| 1.3.6.1.4.1.18.3.4.5.1.45 | ColumnwfSyncRejectsTx | read-only | mandatory | For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in Async mode: Number of frames t… |
| 1.3.6.1.4.1.18.3.4.5.1.46 | ColumnwfSyncRejectsRx | read-only | mandatory | For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a non-matching address For the qu… |
| 1.3.6.1.4.1.18.3.4.5.1.47 | ColumnwfSyncOverFlowRx | read-only | mandatory | Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available. |
| 1.3.6.1.4.1.18.3.4.5.1.48 | ColumnwfSyncFramesIncompRx | read-only | mandatory | Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors. |
| 1.3.6.1.4.1.18.3.4.5.1.49 | ColumnwfSyncBadFramesRx | read-only | mandatory | Number of bad receive frames, caused by FCS errors or non octet aligned. |
| 1.3.6.1.4.1.18.3.4.5.1.50 | ColumnwfSyncFrameRejectsRx | read-only | mandatory | Number of Frame Rejects received |
| 1.3.6.1.4.1.18.3.4.5.1.51 | ColumnwfSyncRuntsRx | read-only | mandatory | Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception. |
| 1.3.6.1.4.1.18.3.4.5.1.52 | ColumnwfSyncT1Timeouts | read-only | mandatory | Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of t… |
| 1.3.6.1.4.1.18.3.4.5.1.53 | ColumnwfSyncMemoryErrors | read-only | mandatory | Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us. |
| 1.3.6.1.4.1.18.3.4.5.1.54 | ColumnwfSyncMediaType | read-write | mandatory | Media type selection is provided via this parameter |
| 1.3.6.1.4.1.18.3.4.5.1.55 | ColumnwfSyncCfgTxQueueLength | read-write | mandatory | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based … |
| 1.3.6.1.4.1.18.3.4.5.1.56 | ColumnwfSyncCfgRxQueueLength | read-write | mandatory | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based d… |
| 1.3.6.1.4.1.18.3.4.5.1.57 | ColumnwfSyncTxQueueLength | read-only | mandatory | Current Transmit Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.58 | ColumnwfSyncRxQueueLength | read-only | mandatory | Current Receive Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.59 | ColumnwfSyncRxReplenMisses | read-only | mandatory | Number of packet buffer misses while attempting to replenish driver receive ring. |
| 1.3.6.1.4.1.18.3.4.5.1.60 | ColumnwfSyncStartUpMode | read-write | mandatory | Initiation of link level for LLC2 running LAPB |
| 1.3.6.1.4.1.18.3.4.5.1.61 | ColumnwfSyncIdleRRFrames | read-write | mandatory | Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent. |
| 1.3.6.1.4.1.18.3.4.5.1.62 | ColumnwfSyncMultilineMode | read-write | mandatory | This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard. |
| 1.3.6.1.4.1.18.3.4.5.1.63 | ColumnwfSyncBODExamPeriod | read-write | mandatory | This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second |
| 1.3.6.1.4.1.18.3.4.5.1.64 | ColumnwfSyncBODFullThreshold | read-write | mandatory | This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested. |
| 1.3.6.1.4.1.18.3.4.5.1.65 | ColumnwfSyncBODRecoverThreshold | read-write | mandatory | This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in o… |
| 1.3.6.1.4.1.18.3.4.5.1.66 | ColumnwfSyncBODPeriodsToFail | read-write | mandatory | This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested. |
| 1.3.6.1.4.1.18.3.4.5.1.67 | ColumnwfSyncKG84ACycle | read-write | mandatory | Monitor sample time in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.68 | ColumnwfSyncKG84ASyncLossInterval | read-write | mandatory | timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization |
| 1.3.6.1.4.1.18.3.4.5.1.69 | ColumnwfSyncKG84ARemoteResyncWait | read-write | mandatory | when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request |
| 1.3.6.1.4.1.18.3.4.5.1.70 | ColumnwfSyncKG84ASyncPulse | read-write | mandatory | interval to pulse KG84a SYNC signal, in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.71 | ColumnwfSyncKG84AResyncs | read-only | mandatory | number of KG84 resyncs performed |
| 1.3.6.1.4.1.18.3.4.5.1.72 | ColumnwfSyncKG84AResyncsDetected | read-only | mandatory | number of KG84 resyncs detected |
| 1.3.6.1.4.1.18.3.4.5.1.73 | ColumnwfSyncKG84ABsu | read-only | mandatory | value taken from mk5025 sync chip control block |
| 1.3.6.1.4.1.18.3.4.5.1.74 | ColumnwfSyncKG84AState | read-only | mandatory | state of sync |
| 1.3.6.1.4.1.18.3.4.5.1.75 | ColumnwfSyncKG84AOkFrames | read-only | mandatory | count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected |
| 1.3.6.1.4.1.18.3.4.5.1.76 | ColumnwfSyncPollingEnable | read-write | mandatory | Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. If disabled, the DSR lead is ign… |
| 1.3.6.1.4.1.18.3.4.5.1.77 | ColumnwfSyncBackupPool | read-write | mandatory | Backup pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.78 | ColumnwfSyncDemandPool | read-write | mandatory | Dial on demand pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.79 | ColumnwfSyncLineNumber | read-write | mandatory | line number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.80 | ColumnwfSyncHoldDownTime | read-write | mandatory | Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a backup configuration and it is … |
| 1.3.6.1.4.1.18.3.4.5.1.81 | ColumnwfSyncNetworkType | read-write | mandatory | Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip revision C04. If a customer mu… |
| 1.3.6.1.4.1.18.3.4.5.1.82 | ColumnwfSyncActiveCct | read-only | mandatory | Active CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.83 | ColumnwfSyncCableType | read-write | mandatory | Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem |
| 1.3.6.1.4.1.18.3.4.5.1.84 | ColumnwfSyncRxDropPackets | read-only | mandatory | Number of Rx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.85 | ColumnwfSyncTxDropPackets | read-only | mandatory | Number of Tx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.86 | ColumnwfSyncModule | read-only | mandatory | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.87 | ColumnwfSyncActualConnector | read-only | mandatory | Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.88 | ColumnwfSyncLineCoding | read-write | mandatory | Line Coding for sync interface. Can be either NRZ or NRZI. |
| 1.3.6.1.4.1.18.3.4.5.1.89 | ColumnwfSyncLastChange | read-only | mandatory | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second… |
| 1.3.6.1.4.1.18.3.4.5.1.90 | ColumnwfSyncOutQLen | read-only | mandatory | The instantaneous current length of the output packet queue (in packets). |
| 1.3.6.1.4.1.18.3.4.5.1.91 | ColumnwfSyncRemoteLpbkDetection | read-write | mandatory | This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is receiving its own BOFL packets a… |
| 1.3.6.1.4.1.18.3.4.5.1.92 | ColumnwfSyncLastState | read-only | mandatory | The state which the driver was in prior to the most recent re-initialization. |
| 1.3.6.1.4.1.18.3.4.5.1.93 | ColumnwfSyncExternalClkSpeed | read-write | mandatory | External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supplied clock. Depending on the pr… |
| 1.3.6.1.4.1.18.3.4.5.1.94 | ColumnwfSyncBChannelOverride | read-write | mandatory | For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instance id, but the user may overrid… |
| 1.3.6.1.4.1.18.3.4.5.1.95 | ColumnwfSyncBChannel | read-only | mandatory | Indicates which B Channel is running |
| 1.3.6.1.4.1.18.3.4.5.1.96 | ColumnwfSyncForceIFTF | read-write | mandatory | Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular channel. For SDLC Lines, DEFAULT an… |
| 1.3.6.1.4.1.18.3.4.5.1.97 | ColumnwfSyncPriority | read-write | mandatory | Used by dial/switched services to assign priority of lines within the same demand or backup pool |
| 1.3.6.1.4.1.18.3.4.5.1.98 | ColumnwfSyncTurboBofl | read-write | mandatory | DEBUG parameter - Turbo bofl enabled or disabled |
| 1.3.6.1.4.1.18.3.4.5.1.99 | ColumnwfSyncBoflNum | read-write | mandatory | DEBUG parameter - Number of breath of life packets per breath of life |
| 1.3.6.1.4.1.18.3.4.5.1.100 | ColumnwfSyncBoflLen | read-write | mandatory | DEBUG parameter - breath of life packet length |
| 1.3.6.1.4.1.18.3.4.5.1.101 | ColumnwfSyncTurboBoflMisses | read-only | mandatory | DEBUG parameter - breath of life allocation failures |
| 1.3.6.1.4.1.18.3.4.5.1.102 | ColumnwfSyncTurboBoflInvocations | read-only | mandatory | DEBUG parameter - breath of life invocations |
| 1.3.6.1.4.1.18.3.4.5.1.103 | ColumnwfSyncBandwidthOnDemandPool | read-write | mandatory | Bandwidth pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.104 | ColumnwfSyncBODRecoverPeriodsToPass | read-write | mandatory | This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line congested. It is used for recove… |
| 1.3.6.1.4.1.18.3.4.5.1.105 | ColumnwfSyncBODHistory | read-only | mandatory | DEBUG parameter - This is the SBOD history buffer. |
| 1.3.6.1.4.1.18.3.4.5.1.106 | ColumnwfSyncBODDebugFlag | read-write | mandatory | DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD. |
| 1.3.6.1.4.1.18.3.4.5.1.107 | ColumnwfSyncBChRateAdaption | read-write | mandatory | This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line mode. This attribute… |
| 1.3.6.1.4.1.18.3.4.5.1.108 | ColumnwfSyncBChActualRateAdaption | read-only | mandatory | Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel ov… |
| 1.3.6.1.4.1.18.3.4.5.1.109 | ColumnwfSyncWanType | read-write | mandatory | This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface. |
| 1.3.6.1.4.1.18.3.4.5.1.110 | ColumnwfSyncAsyncBaudRate | read-write | mandatory | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed.… |
| 1.3.6.1.4.1.18.3.4.5.1.111 | ColumnwfSyncCfgAsyncCmndMaxIdles | read-write | mandatory | Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has … |
| 1.3.6.1.4.1.18.3.4.5.1.112 | ColumnwfSyncAsyncCmndMaxIdles | read-only | mandatory | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), before closing the ASYNC frame. Thi… |
| 1.3.6.1.4.1.18.3.4.5.1.113 | ColumnwfSyncCfgAsyncDataMaxIdles | read-write | mandatory | Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a s… |
| 1.3.6.1.4.1.18.3.4.5.1.114 | ColumnwfSyncAsyncDataMaxIdles | read-only | mandatory | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closing the ASYNC frame. This value … |
| 1.3.6.1.4.1.18.3.4.5.1.115 | ColumnwfSyncFramesAbortTx | read-only | mandatory | Number of frames where CTS was lost during transmission. |
| 1.3.6.1.4.1.18.3.4.5.1.116 | ColumnwfSyncPasyncParityType | read-write | mandatory | Type of parity chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.117 | ColumnwfSyncPasyncCharacterLength | read-write | mandatory | Number of data bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.118 | ColumnwfSyncPasyncStopLength | read-write | mandatory | Number of stop bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.119 | ColumnwfSyncPasyncBaudRate | read-write | mandatory | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed.… |
| 1.3.6.1.4.1.18.3.4.5.1.120 | ColumnwfSyncLocalConnectionState | read-only | mandatory | The state of the cable at the router end. |
| 1.3.6.1.4.1.18.3.4.5.1.121 | ColumnwfSyncRemoteConnectionState | read-only | mandatory | The state of the cable at the device end. |
| 1.3.6.1.4.1.18.3.4.5.1.122 | ColumnwfSyncTimeSlotAssignment | read-only | mandatory | Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by the channel assigned to the FT1… |
| 1.3.6.1.4.1.18.3.4.5.1.123 | ColumnwfSyncEiaStatus | read-only | mandatory | The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted, it is marked as a 1. If not … |
| 1.3.6.1.4.1.18.3.4.5.1.124 | ColumnwfSyncEiaStatusReset | read-write | mandatory | Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status. |
| 1.3.6.1.4.1.18.3.4.5.1.125 | ColumnwfSyncUcastMap | read-write | mandatory | Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames. |
| 1.3.6.1.4.1.18.3.4.5.1.126 | ColumnwfSyncAsyncCfgMaxIdleTimer | read-write | mandatory | Determines if Async Max Idle Timer should be based on the baudrate or on the time needed to receive three characters. |