XYLO-WAN-MIB
385 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.15.2.11.1 | Scalaranxt1Total | read-only | mandatory | The total number of T1/PRI lines on this Annex. |
| 1.3.6.1.4.1.15.2.11.2 | Tableanxt1ConfigT1Table | not-accessible | mandatory | Table of T1 configuration parameters that are not included in the DS1 MIB. |
| 1.3.6.1.4.1.15.2.11.2.1 | Rowanxt1ConfigT1Entry | not-accessible | mandatory | The internal T1 engine parameters. |
| 1.3.6.1.4.1.15.2.11.2.1.1 | Columnanxt1LineIndex | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.11.2.1.2 | Columnanxt1AlarmSyslog | read-write | deprecated | If this object is set to yes(1), all alarm events, red, yellow and blue, are syslogged. In other words, the detection of any one of the alarm events will gener… |
| 1.3.6.1.4.1.15.2.11.2.1.3 | Columnanxt1DiiLineCode | read-write | deprecated | This object selects the line code format used on the T1 Drop and Insert Interface. tni_line_coding is the na/admin corresponding parameter. This object is supp… |
| 1.3.6.1.4.1.15.2.11.2.1.4 | Columnanxt1DiiFraming | read-write | deprecated | This object controls the super frame format used on the T1 Drop and Insert Interface. tdi_framing is the na/admin corresp. parameter. This object is supported … |
| 1.3.6.1.4.1.15.2.11.2.1.5 | Columnanxt1DiiDistance | read-write | deprecated | The distance measured in feet of the cable run to the equipment attached to the Drop and Insert Interface. The default is 0. tdi_distance is the corresp. na/ad… |
| 1.3.6.1.4.1.15.2.11.2.1.6 | Columnanxt1Ds1LineBuildout | read-write | mandatory | At instalation time, the telephone company will supply a measured cable loss measurement between the last line generator and the customer location. This value,… |
| 1.3.6.1.4.1.15.2.11.2.1.7 | Columnanxt1Ds1OnesDensity | read-write | deprecated | This object allows the user to defeat the ones density monitor. The default is off but it should be set to on when using the AMI line coding. tni_ones_density … |
| 1.3.6.1.4.1.15.2.11.2.1.8 | Columnanxt1EngineBypass | read-write | deprecated | when this object is set to yes the T1 engine is taken out of the network. The Network Interface is then physically coupled to the Drop and Insert Interface, an… |
| 1.3.6.1.4.1.15.2.11.2.1.9 | Columnanxt1UnitId | read-only | mandatory | This is a string indicating the firmware version for the T1/PRI engine. |
| 1.3.6.1.4.1.15.2.11.2.1.10 | Columnanxt1UnitSerialNumber | read-only | deprecated | This is the 4 digit T1 engine serial number. This object is supported for T1 modules only. |
| 1.3.6.1.4.1.15.2.11.2.1.11 | Columnanxt1UpTime | read-only | deprecated | Indicates the up time in minutes for the T1 engine. Doing a hard reset will reset this value. Note: This value may not be same as sysupTime if a hard reset has… |
| 1.3.6.1.4.1.15.2.11.2.1.12 | Columnanxt1Info | read-write | deprecated | This objct specifies installation information from the telephone company regarding the T1 line. Corresponding na/admin parameter is t1_info. This object is sup… |
| 1.3.6.1.4.1.15.2.11.2.1.13 | Columnanxt1TotChan | read-only | mandatory | The number of internal DS0 channels on this WAN interface. |
| 1.3.6.1.4.1.15.2.11.2.1.14 | Columnanxt1ResetPRI | read-write | mandatory | Setting this object to enable will reset the PRI line. Setting the object to disable(2) will disable the PRI line and make it unavailable. |
| 1.3.6.1.4.1.15.2.11.2.1.15 | Columnanxt1SwitchType | read-write | mandatory | Select the switch type compatibile with the PRI service provider. default(1) Will select the default switch chosen by the wan manager based on the moduletype. … |
| 1.3.6.1.4.1.15.2.11.2.1.16 | Columnanxt1BlockInCalls | read-write | mandatory | When this object is set to enable, then the box will stop accepting calls on this line. This will prevent new users from logging in and should be used to bring… |
| 1.3.6.1.4.1.15.2.11.2.1.17 | Columnanxt1BlockOutCalls | read-write | mandatory | When this object is set to enable, then the box will not place any outgoing calls. This should be used to bring the box down gracefully. The default is disable… |
| 1.3.6.1.4.1.15.2.11.2.1.18 | Columnanxt1LineLength | read-write | mandatory | This parameter allows the user to configure the dsx1 line driver with the distance between the annex and the external CSU. This paramater should be left to def… |
| 1.3.6.1.4.1.15.2.11.2.1.19 | Columnanxt1AnalogEncoding | read-write | mandatory | This parameter defines the type of encoding to be used for analog (modem) calls. If this parameter is not set then RA6300 will determine itself depending on th… |
| 1.3.6.1.4.1.15.2.11.2.1.20 | Columnanxt1PRIModuleType | read-only | mandatory | This object returns the module type on . e1(1) means PRI module is for Europe, t1(2) means PRI module is for USA with External CSU, t1-intcsu(3) t1/PRI for USA… |
| 1.3.6.1.4.1.15.2.11.2.1.21 | Columnanxt1CasDnisDigits | read-write | mandatory | This parameter allows the user to configure the number of DNIS digits that the channelized T1/E1 interface is provisioned to provide. The default value is 0. T… |
| 1.3.6.1.4.1.15.2.11.2.1.22 | Columnanxt1CasAniDigits | read-write | deprecated | This parameter allows the user to configure the number of ANI digits that the channelized T1/E1 interface is provisioned to provide. The default value is 0. Ty… |
| 1.3.6.1.4.1.15.2.11.2.1.23 | Columnanxt1CasDigitWidth | read-write | mandatory | This parameter allows the width of each digit generated by the WAN module to be adjusted. The default value is 0. This MIB object corresponds to the na/admin p… |
| 1.3.6.1.4.1.15.2.11.2.1.24 | Columnanxt1CasInterDigit | read-write | mandatory | This parameter allows the distance between each digit generated by the WAN module to be adjusted. The default value is 0. This MIB object corresponds to the na… |
| 1.3.6.1.4.1.15.2.11.2.1.25 | Columnanxt1CasDigitPower1 | read-write | mandatory | This parameter allows the power level of the FIRST tone of each digit generated by the WAN module to be adjusted. The default value is 0. This MIB object corre… |
| 1.3.6.1.4.1.15.2.11.2.1.26 | Columnanxt1CasDigitPower2 | read-write | mandatory | This parameter allows the power level of the SECOND tone of each digit generated by the WAN module to be adjusted. The default value is 0. This MIB object corr… |
| 1.3.6.1.4.1.15.2.11.2.1.27 | Columnanxt1CasBusySignalBits | read-write | mandatory | An enumerated integer that defines the type of busy signal. This MIB object corresponds to the na/admin parameter busy_signal_bits. This parameter is available… |
| 1.3.6.1.4.1.15.2.11.2.1.28 | Columnanxt1CasPhoneNumber | read-write | mandatory | The local phone number of the WAN interface. This MIB object corresponds to the na/admin parameter local_phone_number. This parameter is available on platforms… |
| 1.3.6.1.4.1.15.2.11.2.1.29 | Columnanxt1Dsx1LineType | read-write | mandatory | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reaso… |
| 1.3.6.1.4.1.15.2.11.2.1.30 | Columnanxt1Ds1EsfFdl | read-write | deprecated | The NA parameter is tni_esf_fdl (channelized T1 category): This specifies one of two standards when running ESF framing on the T1 Network Interface: Valid opti… |
| 1.3.6.1.4.1.15.2.11.2.1.31 | Columnanxt1TniCircuitId | read-write | deprecated | The NA parameter is tni_circuit_id (channelized T1 category): This is a ascii string with circuit id provided by the telephone company. Up to 127 bytes. This o… |
| 1.3.6.1.4.1.15.2.11.2.1.32 | Columnanxt1TniClock | read-write | deprecated | The NA parameter is tni_clock (channelized T1 category): This specifies the T1 engine clock source: loop, local, external. This object is supported for T1 engi… |
| 1.3.6.1.4.1.15.2.11.2.1.33 | Columnanxt1CallbackEnable | read-write | mandatory | When this object is set to enable, the WAN interface may be selected to handle a callback pending port availability. When set to disable, the associated WAN in… |
| 1.3.6.1.4.1.15.2.11.2.1.34 | Columnanxt1CasAniEnable | read-write | mandatory | This parameter allows the user to configure whether or not to allow CAS ANI digits, (per provisioning). The default is disable. This MIB object corresponds to … |
| 1.3.6.1.4.1.15.2.11.2.1.35 | Columnanxt1Nfasinterfaceid | read-write | mandatory | This is a configurable parameter for NFAS. This MIB object corresponds to the NA/admin WAN parameter 'nfas_interface_id'. |
| 1.3.6.1.4.1.15.2.11.2.1.36 | Columnanxt1Backupinterfaceid | read-write | mandatory | This is a configurable parameter for NFAS. This MIB object corresponds to the NA/admin WAN parameter 'backup_interface_id'. |
| 1.3.6.1.4.1.15.2.11.3 | Tableanxt1ChanTable | not-accessible | mandatory | Table of DS0 channel entries. |
| 1.3.6.1.4.1.15.2.11.3.1 | Rowanxt1ChanEntry | not-accessible | mandatory | The internal T1 engine parameters. |
| 1.3.6.1.4.1.15.2.11.3.1.1 | Columnanxt1ChanIndex | read-only | mandatory | The index value which uniquely identifies the WAN interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.11.3.1.2 | Columnanxt1ChanNumber | read-only | mandatory | A unique number from 1 to anxt1TotChan that identifies each internal DS0 channel on a WAN interface. |
| 1.3.6.1.4.1.15.2.11.3.1.3 | Columnanxt1ChanMap | read-write | deprecated | This object specifies the mapping between the DS0 in the DS1 interface, the DS0 in the DI interface, and the modems. The DS0 is identified by anxt1ChanIfIndex … |
| 1.3.6.1.4.1.15.2.11.3.1.4 | Columnanxt1ChanSigProto | read-write | mandatory | This object is meaningful only when anxt1ChanMap is set to ds1_modem or di_modem and should be ignored in all other cases. The supported protocols are: none(1)… |
| 1.3.6.1.4.1.15.2.11.3.1.5 | Columnanxt1ChanRing | read-write | mandatory | This object is meaningful only when anxt1ChanMap is set to ds1-modem or di-modem and should be ignored in all other cases. This object specifies if the Annex s… |
| 1.3.6.1.4.1.15.2.11.3.1.6 | Columnanxt1ChanIpAddr | read-write | mandatory | This object returns the IP address associated with the B Channel. When needed, this IP address will be used for calls over the B channel. This parameter is ava… |
| 1.3.6.1.4.1.15.2.11.3.1.7 | Columnanxt1ChanIpxNetwork | read-write | mandatory | The IPX network number for an IPX PPP connection using this port. When the IPX PPP connection is established the network number will be negotiated. If one end … |
| 1.3.6.1.4.1.15.2.11.3.1.8 | Columnanxt1ChanIpxNode | read-write | mandatory | The IPX node number for an IPX PPP connection using this port. The value of this object is a 12 digit hexadecimal number string representing the IPX node numbe… |
| 1.3.6.1.4.1.15.2.11.3.1.9 | Columnanxt1ChanStatus | read-only | mandatory | This object returns the status of the B channel. This is a read-only object that indicates whether the channel is in use or not. |
| 1.3.6.1.4.1.15.2.11.3.1.10 | Columnanxt1ChanState | read-write | mandatory | This object reflects the state of the B channel. Available means it is open for use, busied-out means it was manually taken out of the pool for use, and auto-b… |
| 1.3.6.1.4.1.15.2.11.3.1.11 | Columnanxt1ChanSeize | read-only | mandatory | SEIZE message from a WAN module to a WAN manager process on the main processor, indicating that the central office switch has sent a channelized T1/E1 seize ev… |
| 1.3.6.1.4.1.15.2.11.3.1.12 | Columnanxt1ChanRingCount | read-only | mandatory | RING message from a WAN module to a WAN manager process on the main processor, indicating that a call has arrived. Successful completion of assigning a modem a… |
| 1.3.6.1.4.1.15.2.11.3.1.13 | Columnanxt1ChanAssign | read-only | mandatory | No modems were available for assignment. This is caused by not having enough modems or modems being removed from the pool |
| 1.3.6.1.4.1.15.2.11.3.1.14 | Columnanxt1ChanConnect | read-only | mandatory | CONNECT message from the WAN module to the WAN manager process, meaning the 5399 has accepted the call and the WAN module and the telephone company switch have… |
| 1.3.6.1.4.1.15.2.11.3.1.15 | Columnanxt1ChanChat | read-only | mandatory | There was a modem error and the call was terminated. Possibly caused by the modem. |
| 1.3.6.1.4.1.15.2.11.3.1.16 | Columnanxt1ChanDcd | read-only | mandatory | Modem did not establish a connection with it's peer. Lots of possible causes: many possible causes: modem error bad data from bad channel end-to-end line quali… |
| 1.3.6.1.4.1.15.2.11.3.1.17 | Columnanxt1ChanModemCall | read-only | mandatory | The number of times an incoming modem call failed before getting all the way to DCD. |
| 1.3.6.1.4.1.15.2.11.3.1.18 | Columnanxt1ChanConsecFail | read-only | mandatory | The number of times an incoming non-modem call failed before successfully assigning a device. |
| 1.3.6.1.4.1.15.2.11.4 | Tableanxt1CurrentTable | not-accessible | mandatory | Table of extended T1 current statistics. This table is valid for WAN module platforms only. |
| 1.3.6.1.4.1.15.2.11.4.1 | Rowanxt1CurrentEntry | not-accessible | mandatory | The internal T1 engine extended current statistics. |
| 1.3.6.1.4.1.15.2.11.4.1.1 | Columnanxt1CurrentIndex | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.11.4.1.2 | Columnanxt1CurrentOofs | read-only | mandatory | An Out Of Frame (OOF) event begins when any two of four consecutive frame synchronizing bits are received from the network interface are incorrect. An OOF stat… |
| 1.3.6.1.4.1.15.2.11.4.1.3 | Columnanxt1CurrentBpvs | read-only | mandatory | A BiPolar Violations error event for an AMI-coded signal is the occurence of a pulse of the same polarity as the previous pulse. A BPV error event for a B8ZS o… |
| 1.3.6.1.4.1.15.2.11.4.1.4 | Columnanxt1CurrentCrcs | read-only | mandatory | A CRC error occurs when the CRC field calculated by the customer installation, based on the incoming DS1 signal does not agree with the CRC field contained in … |
| 1.3.6.1.4.1.15.2.11.4.1.5 | Columnanxt1CurrentCs | read-only | mandatory | A Controlled Slips is the occcurence of a replication or deletion of a DS1 frame by the receiving terminal. |
| 1.3.6.1.4.1.15.2.11.4.1.6 | Columnanxt1CurrentRnacs | read-only | mandatory | Receive Network Alarm seconds is the count of seconds with at least one alarm event occurring in a second. |
| 1.3.6.1.4.1.15.2.11.4.1.7 | Columnanxt1CurrentEsfs | read-only | mandatory | The count of extended superframe errors in the current interval. |
| 1.3.6.1.4.1.15.2.11.4.1.8 | Columnanxt1CurrentLofcs | read-only | mandatory | The count of loss of framing errors in the current interval. |
| 1.3.6.1.4.1.15.2.11.5 | Tableanxt1IntervalTable | not-accessible | mandatory | Table of extended T1 interval statistics. This table is valid for WAN module platforms only. |
| 1.3.6.1.4.1.15.2.11.5.1 | Rowanxt1IntervalEntry | not-accessible | mandatory | The internal T1 engine extended interval statistics. |
| 1.3.6.1.4.1.15.2.11.5.1.1 | Columnanxt1IntervalIndex | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.11.5.1.2 | Columnanxt1IntervalNumber | read-only | mandatory | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that … |
| 1.3.6.1.4.1.15.2.11.5.1.3 | Columnanxt1IntervalOofs | read-only | mandatory | An Out Of Frame (OOF) event begins when any two of four consecutive frame synchronizing bits are received from the network interface are incorrect. An OOF stat… |
| 1.3.6.1.4.1.15.2.11.5.1.4 | Columnanxt1IntervalBpvs | read-only | mandatory | A BiPolar Violations error event for an AMI-coded signal is the occurence of a pulse of the same polarity as the previous pulse. A BPV error event for a B8ZS o… |
| 1.3.6.1.4.1.15.2.11.5.1.5 | Columnanxt1IntervalCrcs | read-only | mandatory | A CRC error occurs when the CRC field calculated by the customer installation, based on the incoming DS1 signal does not agree with the CRC field contained in … |
| 1.3.6.1.4.1.15.2.11.5.1.6 | Columnanxt1IntervalCs | read-only | mandatory | A Controlled Slips is the occcurence of a replication or deletion of a DS1 frame by the receiving terminal. |
| 1.3.6.1.4.1.15.2.11.5.1.7 | Columnanxt1IntervalRnacs | read-only | mandatory | Receive Network Alarm seconds is the count of seconds with at least one alarm event occurring in a second. |
| 1.3.6.1.4.1.15.2.11.5.1.8 | Columnanxt1IntervalEsfs | read-only | mandatory | The count of extended superframe errors in this interval. |
| 1.3.6.1.4.1.15.2.11.5.1.9 | Columnanxt1IntervalLofcs | read-only | mandatory | The count of loss of framing errors in this interval. |
| 1.3.6.1.4.1.15.2.11.6 | Tableanxt1TotalTable | not-accessible | mandatory | Table of extended T1 total statistics. This table is valid for WAN module platforms only. |
| 1.3.6.1.4.1.15.2.11.6.1 | Rowanxt1TotalEntry | not-accessible | mandatory | The internal T1 engine extended total statistics. |
| 1.3.6.1.4.1.15.2.11.6.1.1 | Columnanxt1TotalIndex | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.11.6.1.2 | Columnanxt1TotalOofs | read-only | mandatory | An Out Of Frame (OOF) event begins when any two of four consecutive frame synchronizing bits are received from the network interface are incorrect. An OOF stat… |
| 1.3.6.1.4.1.15.2.11.6.1.3 | Columnanxt1TotalBpvs | read-only | mandatory | A BiPolar Violations error event for an AMI-coded signal is the occurence of a pulse of the same polarity as the previous pulse. A BPV error event for a B8ZS o… |
| 1.3.6.1.4.1.15.2.11.6.1.4 | Columnanxt1TotalCrcs | read-only | mandatory | A CRC error occurs when the CRC field calculated by the customer installation, based on the incoming DS1 signal does not agree with the CRC field contained in … |
| 1.3.6.1.4.1.15.2.11.6.1.5 | Columnanxt1TotalCs | read-only | mandatory | A Controlled Slips is the occcurence of a replication or deletion of a DS1 frame by the receiving terminal. |
| 1.3.6.1.4.1.15.2.11.6.1.6 | Columnanxt1TotalRnacs | read-only | mandatory | Receive Network Alarm seconds is the count of seconds with at least one alarm event occurring in a second. |
| 1.3.6.1.4.1.15.2.11.6.1.7 | Columnanxt1TotalEsfs | read-only | mandatory | The total count of extended superframe errors. |
| 1.3.6.1.4.1.15.2.11.6.1.8 | Columnanxt1TotalLofcs | read-only | mandatory | The total count of loss of framing errors. |
| 1.3.6.1.4.1.15.2.11.7 | Tableanxt1WanModuleTable | not-accessible | mandatory | This table is is used to cross reference a WAN module to its ifindex. |
| 1.3.6.1.4.1.15.2.11.7.1 | Rowanxt1WanModuleEntry | not-accessible | mandatory | WAN module table entry. |
| 1.3.6.1.4.1.15.2.11.7.1.1 | Columnanxt1WanIndex | read-only | mandatory | This is the index of the physical WAN module in any BAY remote access product that uses WAN modules. The range is 1 - anxt1Total (number of WAN modules in box) |
| 1.3.6.1.4.1.15.2.11.7.1.2 | Columnanxt1WanIfIndex | read-only | mandatory | This object can be used in place of Ifindex to find the interface number of a WAN module. |
| 1.3.6.1.4.1.15.2.11.8 | Scalaranxt1TotalChannels | read-only | mandatory | The total number of channels (Ds0's) on the this box (or blade). |
| 1.3.6.1.4.1.15.2.11.9 | Scalaranxt1BusiedOutChannels | read-only | mandatory | The number of channels that are busied out. anxt1TotalChannels - anxt1BusiedOutChannels = Number of available channels |
| 1.3.6.1.4.1.15.2.11.10 | TablewanStatTable | not-accessible | mandatory | Table of Wan Module statistics. This table is valid for WAN module platforms only. |
| 1.3.6.1.4.1.15.2.11.10.1 | RowwanStatEntry | not-accessible | mandatory | The internal T1 engine extended current statistics. |
| 1.3.6.1.4.1.15.2.11.10.1.1 | ColumnwanStatIndex | read-only | mandatory | The ifIndex value in the interfaces table. Look at anxt1WanModuleTable for an alternative way of getting the interface number for a physical WAN module |
| 1.3.6.1.4.1.15.2.11.10.1.2 | ColumnwanStatInterfaceErrs | read-only | mandatory | This counter is incremented when ever an error occurs between the wan module and the PRI manager. |
| 1.3.6.1.4.1.15.2.11.10.1.3 | ColumnwanStatAcceptedInCalls | read-only | mandatory | Number of incoming calls accepted by the call handler. (call handler is generic term for all types of signaling methods) |
| 1.3.6.1.4.1.15.2.11.10.1.4 | ColumnwanStatRejectedInCalls | read-only | mandatory | Number of incoming calls rejected by the call handler. (call handler is generic term for all types of signaling methods) |
| 1.3.6.1.4.1.15.2.11.10.1.5 | ColumnwanStatAcceptedOutCalls | read-only | mandatory | Number of outgoing calls accepted by the call handler. (call handler is generic term for all types of signaling methods) |
| 1.3.6.1.4.1.15.2.11.10.1.6 | ColumnwanStatRejectedOutCalls | read-only | mandatory | Number of outgoing calls rejected by the call handler. (call handler is generic term for all types of signaling methods) |
| 1.3.6.1.4.1.15.2.11.10.1.7 | ColumnwanStatNormalCallDisconnects | read-only | mandatory | Number of normal disconnects. Normal Disconnects cause codes: - NORMAL_CALL_CLEARING_CCOD |
| 1.3.6.1.4.1.15.2.11.10.1.8 | ColumnwanStatAbNormalCallDisconnects | read-only | mandatory | Number of abnormal disconnects. Abnormal Disconnects cause codes: - INVALID_NUMBER_FORMAT_CCODE - NO_CKT_CHAN_AVAIL_CCODE - REQ_CHAN_NOT_AVAIL_CCODE |
| 1.3.6.1.4.1.15.2.11.10.1.9 | ColumnwanStatBchansCurrAllocated | read-only | mandatory | Number of B channels currently allocated. |
| 1.3.6.1.4.1.15.2.11.10.1.10 | ColumnwanStatNumTimesWanFull | read-only | mandatory | Number of times this wan has had all B channels allocated since the wan_manager process was started on the wan module. The wan_manager process is started at bo… |
| 1.3.6.1.4.1.15.2.12.1 | Nodeconnections | |||
| 1.3.6.1.4.1.15.2.12.1.1 | TablecallGenericTable | not-accessible | mandatory | Table of entries of generic parameters for active calls. |
| 1.3.6.1.4.1.15.2.12.1.1.1 | RowcallGenericEntry | not-accessible | mandatory | The call's generic parameters. |
| 1.3.6.1.4.1.15.2.12.1.1.1.1 | ColumncallGenericLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.1.1.2 | ColumncallGenericIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.1.1.3 | ColumncallGenericMode | read-only | mandatory | Mode assigned to the port. Valid only if the port type is async, or ta. The default is cli. This MIB object corresponds to the NA/admin asynchronous, ta, synch… |
| 1.3.6.1.4.1.15.2.12.1.1.1.4 | ColumncallGenericLocation | read-only | mandatory | A descriptive string for this port. This string is displayed by the CLI who command. This MIB object corresponds to the NA/admin asynchronous, ta, synchronous … |
| 1.3.6.1.4.1.15.2.12.1.1.1.5 | ColumncallGenericTermVar | read-only | mandatory | A string defining the type of terminal attached to the serial/ta port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'term_var'. N… |
| 1.3.6.1.4.1.15.2.12.1.1.1.6 | ColumncallGenericPrompt | read-only | mandatory | This parameter defines a port-specific prompt string. The prompt string consists of displayable characters and embedded formatting codes. Each formatting code … |
| 1.3.6.1.4.1.15.2.12.1.1.1.8 | ColumncallGenericAllowBcast | read-only | mandatory | Controls whether the serial/ta port can receive administrative broadcast messages. This MIB object corresponds to the NA/admin asynchronous/ta port parameter '… |
| 1.3.6.1.4.1.15.2.12.1.1.1.10 | ColumncallGenericImask7Bits | read-only | mandatory | When enabled, instructs the Annex to ignore the eighth bit of all received characters on the port. This MIB object corresponds to the NA/admin asynchronous/ta … |
| 1.3.6.1.4.1.15.2.12.1.1.1.11 | ColumncallGenericCliImask7 | read-only | mandatory | Defines whether input at the CLI is masked to 7 bits. The default is disabled. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'cli_… |
| 1.3.6.1.4.1.15.2.12.1.1.1.12 | ColumncallGenericBanner | read-only | mandatory | Specifies whether the Annex banner and message- of-the-day are displayed on the channel. The default is enabled. This has four possible actions: default, Y, ye… |
| 1.3.6.1.4.1.15.2.12.1.1.1.13 | ColumncallGenericTcpKeepAlive | read-only | mandatory | The default keep-alive value for connections to this serial port. If this is zero, use the value specified by anxTcpKeepAlive. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.1.1.1.14 | ColumncallGenericDedicatedArgs | read-only | mandatory | Command line arguments passed to process started by a dedicated port with mode set to 'telnet', 'tn3270', 'rlogin', 'connect' (if LAT is in use) or 'call'. Thi… |
| 1.3.6.1.4.1.15.2.12.1.1.1.15 | ColumncallGenericModemVar | read-only | mandatory | A string defining the type of modem attached to the serial port. This object is not valid for TA ports. This is always set to 'microcom'. This MIB object corre… |
| 1.3.6.1.4.1.15.2.12.1.1.1.16 | ColumncallGenericDefSessMode | read-only | mandatory | The default session mode when the DECServer command interface is configured. The default is interactive. This MIB object corresponds to the NA/admin asynchrono… |
| 1.3.6.1.4.1.15.2.12.1.1.1.17 | ColumncallGenericResolveProtocol | read-only | mandatory | Default host protocol to use when starting a dedicated port and the protocol is not explicitly specified in the command. Is set to one of 'telnet', connect, or… |
| 1.3.6.1.4.1.15.2.12.1.1.1.18 | ColumncallGenericMaxSession | read-only | mandatory | The maximum number of concurrent sessions allowed on the port. A value of -1 indicates no maximum. Setting the maximum to less than the current number of sessi… |
| 1.3.6.1.4.1.15.2.12.1.1.1.19 | ColumncallGenericSpeed | read-only | mandatory | The maximum speed of the port for this call. |
| 1.3.6.1.4.1.15.2.12.1.1.1.20 | ColumncallGenericAutoBaud | read-only | mandatory | This is always set to disabled. |
| 1.3.6.1.4.1.15.2.12.1.1.1.21 | ColumncallGenericJobs | read-only | mandatory | Job list for this cli session. |
| 1.3.6.1.4.1.15.2.12.1.1.1.22 | ColumncallGenericLineType | read-only | mandatory | This is what the port is running at the moment. callgenericmode will tell you what the port is configured to run through the spb or e2rom. |
| 1.3.6.1.4.1.15.2.12.1.2 | TablecallSignalTable | not-accessible | mandatory | Table of entries for port flow control and signal parameters. |
| 1.3.6.1.4.1.15.2.12.1.2.1 | RowcallSignalEntry | not-accessible | mandatory | The table of entries of flow control and signal parameters for active calls. |
| 1.3.6.1.4.1.15.2.12.1.2.1.1 | ColumncallSignalLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.2.1.2 | ColumncallSignalIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.2.1.4 | ColumncallSignalInputStartChar | read-only | mandatory | The control character sequence that restarts input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be ei… |
| 1.3.6.1.4.1.15.2.12.1.2.1.5 | ColumncallSignalInputStopChar | read-only | mandatory | The control character sequence that stops input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be eithe… |
| 1.3.6.1.4.1.15.2.12.1.2.1.6 | ColumncallSignalOutputStartChar | read-only | mandatory | The control character sequence that restarts output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be … |
| 1.3.6.1.4.1.15.2.12.1.2.1.7 | ColumncallSignalOutputStopChar | read-only | mandatory | The control character sequence that stops output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be eit… |
| 1.3.6.1.4.1.15.2.12.1.2.1.8 | ColumncallSignalIxanyFlowCtrl | read-only | mandatory | This parameter specifies whether any input character will be treated as a start (xon) character when output has been suspended by a stop (xoff) character. This… |
| 1.3.6.1.4.1.15.2.12.1.2.1.10 | ColumncallSignalForwardKey | read-only | mandatory | Defines a control character sequence as an attention character to switch the user to the next session. The Annex-II only allows a single control character (eg.… |
| 1.3.6.1.4.1.15.2.12.1.2.1.11 | ColumncallSignalBackwardKey | read-only | mandatory | Defines a control character sequence as an attention character to switch the user to the previous session. The Annex-II only allows a single control character … |
| 1.3.6.1.4.1.15.2.12.1.2.1.17 | ColumncallSignalCharInFlow | read-only | mandatory | The port's type of input flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON an… |
| 1.3.6.1.4.1.15.2.12.1.2.1.18 | ColumncallSignalCharOutFlow | read-only | mandatory | The port's type of output flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON a… |
| 1.3.6.1.4.1.15.2.12.1.2.1.19 | ColumncallSignalrs232AsyncBits | read-write | deprecated | The port's number of bits in a character. This object corresponds to the admin parameter data_bits. |
| 1.3.6.1.4.1.15.2.12.1.2.1.20 | ColumncallSignalrs232AsyncStopBits | read-write | deprecated | The port's number of stop bits. This object corresponds to the admin parameter stop_bits. |
| 1.3.6.1.4.1.15.2.12.1.2.1.21 | ColumncallSignalrs232AsyncParity | read-write | deprecated | The port's sense of a character parity bit. |
| 1.3.6.1.4.1.15.2.12.1.3 | TablecallLoginTable | not-accessible | mandatory | Table of entries of login parameters for active calls. Note: This table is not valid for Synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.3.1 | RowcallLoginEntry | not-accessible | mandatory | Call's login user parameters. |
| 1.3.6.1.4.1.15.2.12.1.3.1.1 | ColumncallLoginLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.3.1.2 | ColumncallLoginIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.3.1.3 | ColumncallLoginVciLoginPortPasswd | read-only | deprecated | Indicates if the port is configured as a DECServer interface port. The default is disabled. This MIB object corresponds to the NA/admin asynchronous/ta port pa… |
| 1.3.6.1.4.1.15.2.12.1.3.1.4 | ColumncallLoginVciLoginTimeout | read-only | deprecated | Enables a login timer if the port is configured as a DECServer interface port. The default is disabled. This MIB object corresponds to the NA/admin asynchronou… |
| 1.3.6.1.4.1.15.2.12.1.4 | TablecallTimerTable | not-accessible | mandatory | Table of entries of port timer and counter parameters for active calls. Note: This table is not valid for Synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.4.1 | RowcallTimerEntry | not-accessible | mandatory | Call's timer and counter parameters. |
| 1.3.6.1.4.1.15.2.12.1.4.1.1 | ColumncallTimerLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.4.1.2 | ColumncallTimerIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.4.1.3 | ColumncallTimerForwardTimer | read-only | mandatory | This parameter defines the inter-character timer that sets the amount of time, in tens of milliseconds, that will elapse before forwarding the received data. T… |
| 1.3.6.1.4.1.15.2.12.1.4.1.4 | ColumncallTimerForwardCount | read-only | mandatory | Specifies the number of received characters buffered for the port by the Annex before forwarding the characters to the host or network. This MIB object corresp… |
| 1.3.6.1.4.1.15.2.12.1.4.1.5 | ColumncallTimerCliInactivity | read-only | mandatory | The amount of time, in minutes, that the Annex waits before hanging up the serial/ta port after it becomes idle. A value of 0 indicates the timer is off. A val… |
| 1.3.6.1.4.1.15.2.12.1.4.1.6 | ColumncallTimerCliInactivityTimer | read-only | mandatory | The amount of time, in minutes, which a port can remain inactive before the Annex terminates all sessions and resets the port. A value of 0 implies timer is di… |
| 1.3.6.1.4.1.15.2.12.1.4.1.7 | ColumncallTimerInputIsActivity | read-only | mandatory | Controls whether received input characters are considered as activity for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter … |
| 1.3.6.1.4.1.15.2.12.1.4.1.8 | ColumncallTimerOutputIsActivity | read-only | mandatory | Controls whether transmitted output characters are considered as activity for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parame… |
| 1.3.6.1.4.1.15.2.12.1.4.1.9 | ColumncallTimerResetIdleTimer | read-only | mandatory | Defines whether input or output resets the idle timer for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'reset_idle_time… |
| 1.3.6.1.4.1.15.2.12.1.4.1.10 | ColumncallTimerLongBreak | read-only | mandatory | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break greater than two seconds. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.1.4.1.11 | ColumncallTimerShortBreak | read-only | mandatory | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break shorter than two seconds. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.1.5 | TablecallSecurityTable | not-accessible | mandatory | Table of entries of port security parameters for active calls. |
| 1.3.6.1.4.1.15.2.12.1.5.1 | RowcallSecurityEntry | not-accessible | mandatory | Call's security parameters. |
| 1.3.6.1.4.1.15.2.12.1.5.1.1 | ColumncallSecurityLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.5.1.2 | ColumncallSecurityIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.5.1.3 | ColumncallSecurityUserName | read-only | mandatory | A string defining the default user name for the user of this serial/ta port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'user_n… |
| 1.3.6.1.4.1.15.2.12.1.5.1.4 | ColumncallSecurityCli | read-only | mandatory | This parameter controls whether security is enabled for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'cli_security'. |
| 1.3.6.1.4.1.15.2.12.1.5.1.5 | ColumncallSecurityConnect | read-only | mandatory | This parameter controls whether the host-based security policy is enabled for access from the port to the network. This MIB object corresponds to the NA/admin … |
| 1.3.6.1.4.1.15.2.12.1.5.1.6 | ColumncallSecurityPortServer | read-only | mandatory | This parameter controls whether the host-based security policy is enabled for access to the port from the port server. This MIB object corresponds to the NA/ad… |
| 1.3.6.1.4.1.15.2.12.1.5.1.7 | ColumncallSecurityPortPasswd | read-only | mandatory | This parameter defines a password for the port for local password protection. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'port_… |
| 1.3.6.1.4.1.15.2.12.1.5.1.8 | ColumncallSecurityIpsoClass | read-only | mandatory | Defines the IP security classification for packets sent and received on this port. The default value is none. This MIB object corresponds to the NA/admin async… |
| 1.3.6.1.4.1.15.2.12.1.5.1.9 | ColumncallSecurityIpx | read-only | mandatory | Controls whether IPX security is enabled on this port. The default is disabled. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'ipx… |
| 1.3.6.1.4.1.15.2.12.1.5.1.10 | ColumncallSecurityCurrentUser | read-only | mandatory | Returns the username for an active call on a b channel. This MIB object is only valid if security is enabled. |
| 1.3.6.1.4.1.15.2.12.1.6 | TablecallLineEditTable | not-accessible | mandatory | Table of entries of line editing parameters for active calls. Note: This table is not valid for synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.6.1 | RowcallLineEditEntry | not-accessible | mandatory | Call's line editing parameters. |
| 1.3.6.1.4.1.15.2.12.1.6.1.1 | ColumncallLineEditLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.6.1.2 | ColumncallLineEditIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.6.1.3 | ColumncallLineEditAttnChar | read-only | mandatory | Defines a control character sequence as an attention character to return the user to the CLI prompt. The Annex-II only allows a single control character (eg. ^… |
| 1.3.6.1.4.1.15.2.12.1.6.1.4 | ColumncallLineEditEcho | read-only | mandatory | This parameter controls whether the Annex echoes all characters as they are received from the port. This MIB object corresponds to the NA/admin asynchronous/ta… |
| 1.3.6.1.4.1.15.2.12.1.6.1.5 | ColumncallLineEditTelnetEscape | read-only | mandatory | Defines the control character that returns the user to the 'telnet:' prompt when running the CLI telnet command. This value of this object can be either a sing… |
| 1.3.6.1.4.1.15.2.12.1.6.1.6 | ColumncallLineEditTelnetCRLF | read-only | mandatory | Defines what characters are transmitted out the port to the network when the End-of-Line character is sensed. 'enabled' means transmit Line-Feed and Carriage-R… |
| 1.3.6.1.4.1.15.2.12.1.6.1.7 | ColumncallLineEditMapToLower | read-only | mandatory | When enabled, the Annex translates all upper case characters to lower case as they are received from the port. This MIB object corresponds to the NA/admin asyn… |
| 1.3.6.1.4.1.15.2.12.1.6.1.8 | ColumncallLineEditMapToUpper | read-only | mandatory | When enabled, the Annex translates all lower case characters to upper case as they are transmitted to the port. This MIB object corresponds to the NA/admin asy… |
| 1.3.6.1.4.1.15.2.12.1.6.1.9 | ColumncallLineEditCharErase | read-only | mandatory | This parameter controls whether the Annex echoes the character erase and word erase characters for a video terminal (enabled) or for a hard-copy terminal (disa… |
| 1.3.6.1.4.1.15.2.12.1.6.1.10 | ColumncallLineEditEraseChar | read-only | mandatory | Defines the character erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^… |
| 1.3.6.1.4.1.15.2.12.1.6.1.11 | ColumncallLineEditLineErase | read-only | mandatory | This parameter controls whether the Annex echoes the line erase character for a video terminal (enabled) or for a hard-copy terminal (disabled). This MIB objec… |
| 1.3.6.1.4.1.15.2.12.1.6.1.12 | ColumncallLineEditEraseLine | read-only | mandatory | Defines the line erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x', w… |
| 1.3.6.1.4.1.15.2.12.1.6.1.13 | ColumncallLineEditEraseWord | read-only | mandatory | Defines the word erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x', w… |
| 1.3.6.1.4.1.15.2.12.1.6.1.14 | ColumncallLineEditHardwareTabs | read-only | mandatory | When enabled, this parameter allows the Annex to expand ASCII tab characters. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'hardw… |
| 1.3.6.1.4.1.15.2.12.1.6.1.15 | ColumncallLineEditRedisplayLine | read-only | mandatory | Defines the reprint line control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x',… |
| 1.3.6.1.4.1.15.2.12.1.6.1.16 | ColumncallLineEditToggleOutput | read-only | mandatory | Defines the flush control character used to flush the output buffer. This value of this object can be either a single displayable character or two characters o… |
| 1.3.6.1.4.1.15.2.12.1.6.1.17 | ColumncallLineEditNewLineTerm | read-only | mandatory | This parameter controls whether a carriage return is echoed as just a carriage return (enabled), or whether the carriage return is echoed as a carriage return … |
| 1.3.6.1.4.1.15.2.12.1.7 | TablecallNetTable | not-accessible | mandatory | Table of entries of networking protocol parameters for active calls. |
| 1.3.6.1.4.1.15.2.12.1.7.1 | RowcallNetEntry | not-accessible | mandatory | Call's networking protocol parameters. |
| 1.3.6.1.4.1.15.2.12.1.7.1.1 | ColumncallNetLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.7.1.2 | ColumncallNetIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.7.1.3 | ColumncallNetLocalAddr | read-only | mandatory | The Internet address for the Annex's side of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the NA/admin asynchronous, ta, synchronous p… |
| 1.3.6.1.4.1.15.2.12.1.7.1.4 | ColumncallNetRemoteAddr | read-only | mandatory | The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the NA/admin asynchronous, ta, syn… |
| 1.3.6.1.4.1.15.2.12.1.7.1.6 | ColumncallNetMetric | read-only | mandatory | This parameter defines the hop count to the remote end of the SLIP or PPP interface. This MIB object corresponds to the NA/admin asynchronous, ta. synchronous … |
| 1.3.6.1.4.1.15.2.12.1.7.1.7 | ColumncallNetSlipSecure | read-only | mandatory | If anxEnableSecurity is disabled, this parameter selects slip session logging. If anxEnableSecurity is enabled, this parameter permits slip access only from se… |
| 1.3.6.1.4.1.15.2.12.1.7.1.8 | ColumncallNetInactivity | read-only | mandatory | The number of units allowed for serial protocol inactivity on the port. The type of unit, minutes or seconds, is defined by the object anxpNetInactivityUnits. … |
| 1.3.6.1.4.1.15.2.12.1.7.1.9 | ColumncallNetDoCompression | read-only | mandatory | When enabled, the Annex will attempt to negotiate TCP/IP header compression on this serial link. This MIB object corresponds to the NA/admin asynchronous/ta/sy… |
| 1.3.6.1.4.1.15.2.12.1.7.1.10 | ColumncallNetAllowCompression | read-only | mandatory | When enabled, the Annex will allow TCP/IP header compression on this serial link only if the other end of the serial link initiates the compression. This MIB o… |
| 1.3.6.1.4.1.15.2.12.1.7.1.11 | ColumncallNetInactivityUnits | read-only | mandatory | The type of units that are used for the port's net inactivity timer. See also the anxpNetInactivity object. The default value is 'minutes'. This MIB object cor… |
| 1.3.6.1.4.1.15.2.12.1.8 | TablecallSlipTable | not-accessible | mandatory | Table of entries of Slip parameters for active calls. Note: This object is not valid for Synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.8.1 | RowcallSlipEntry | not-accessible | mandatory | Call's Slip parameters. |
| 1.3.6.1.4.1.15.2.12.1.8.1.1 | ColumncallSlipLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.8.1.2 | ColumncallSlipIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.8.1.3 | ColumncallSlipSubnetMask | read-only | mandatory | The subnet mask for this SLIP interface. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'subnet_mask'. |
| 1.3.6.1.4.1.15.2.12.1.8.1.4 | ColumncallSlipMtuSize | read-only | mandatory | Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). The default is large. This MIB … |
| 1.3.6.1.4.1.15.2.12.1.8.1.5 | ColumncallSlipNoIcmp | read-only | mandatory | When enabled, the Annex will discard any ICMP packets directed to this SLIP link. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 's… |
| 1.3.6.1.4.1.15.2.12.1.8.1.6 | ColumncallSlipTos | read-only | mandatory | When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic. This MIB object corresponds to the NA/admin asynchronous/ta por… |
| 1.3.6.1.4.1.15.2.12.1.9 | TablecallPPPTable | not-accessible | mandatory | Table of entries of PPP parameters for active calls. |
| 1.3.6.1.4.1.15.2.12.1.9.1 | RowcallPPPEntry | not-accessible | mandatory | Call's PPP parameters. |
| 1.3.6.1.4.1.15.2.12.1.9.1.1 | ColumncallPPPLineIdx | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.9.1.2 | ColumncallPPPIdx | read-only | mandatory | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.9.1.3 | ColumncallPPPMru | read-only | mandatory | This parameter defines the maximum receive unit in bytes. The default value is 1500. This MIB object corresponds to the NA/admin asynchronous, ta, and synchron… |
| 1.3.6.1.4.1.15.2.12.1.9.1.4 | ColumncallPPPAcm | read-only | mandatory | This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A bit on in the mask indicates th… |
| 1.3.6.1.4.1.15.2.12.1.9.1.5 | ColumncallPPPSecurityProto | read-only | mandatory | Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_security (anxEnableSecurity) must… |
| 1.3.6.1.4.1.15.2.12.1.9.1.6 | ColumncallPPPRemoteUser | read-only | mandatory | The username used by the Annex to identify itself if the remote PPP peer asks for authentication. This MIB object corresponds to the NA/admin asynchronous/ta/s… |
| 1.3.6.1.4.1.15.2.12.1.9.1.7 | ColumncallPPPRemotePasswd | read-only | mandatory | The password used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either <set> if the passwo… |
| 1.3.6.1.4.1.15.2.12.1.9.1.8 | ColumncallPPPNcp | read-only | mandatory | A bitmask for PPP NCP Options: 0x0002 NCP_IPCP 0x0004 NCP_ATCP 0x0008 NCP_IPXCP 0x0010 NCP_MP 0x0020 NCP_CCP 0x0040 NCP_CBCP Note: if the ncp_option parameter … |
| 1.3.6.1.4.1.15.2.12.1.9.1.9 | ColumncallPPPIpxNetwork | read-only | mandatory | The IPX network number for an IPX PPP connection using this port. When the IPX PPP connection is established the network number will be negotiated. If one end … |
| 1.3.6.1.4.1.15.2.12.1.9.1.10 | ColumncallPPPIpxNode | read-only | mandatory | The IPX node number for an IPX PPP connection using this port. The value of this object is a 12 digit hexadecimal number string representing the IPX node numbe… |
| 1.3.6.1.4.1.15.2.12.1.9.1.11 | ColumncallPPPTraceLevel | read-write | mandatory | Controls whether PPP trace messages are sent to the syslog facility or not. The default value is none(0). This MIB object corresponds to the na/admin port para… |
| 1.3.6.1.4.1.15.2.12.1.10 | TablecallARAPTable | not-accessible | deprecated | Table of entries of Apple Talk parameters for active calls. Note: This object is not valid for Synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.10.1 | RowcallARAPEntry | not-accessible | deprecated | Call's ARAP parameters. |
| 1.3.6.1.4.1.15.2.12.1.10.1.1 | ColumncallARAPLineIdx | read-only | deprecated | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.10.1.2 | ColumncallARAPIdx | read-only | deprecated | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.10.1.3 | ColumncallARAPGuest | read-only | deprecated | If enabled, allows ARAP guest login service. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'at_guest'. |
| 1.3.6.1.4.1.15.2.12.1.10.1.4 | ColumncallARAPNodeId | read-only | deprecated | The default AppleTalk node ID hint that is used by the Annex on this port. The address consists of two parts separated by a dot. The address may be in either h… |
| 1.3.6.1.4.1.15.2.12.1.10.1.5 | ColumncallARAPSecurity | read-only | deprecated | Controls whether ACP service is enabled for this port when establishing an AppleTalk connection. This MIB object corresponds to the NA/admin asynchronous/ta po… |
| 1.3.6.1.4.1.15.2.12.1.10.1.6 | ColumncallARAPV42BIS | read-only | deprecated | Controls whether V.42bis compression is done during an ARAP session. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'arap_v42bis'. |
| 1.3.6.1.4.1.15.2.12.1.11 | TablecallTN3270Table | not-accessible | deprecated | Table of entries of TN3270 parameters for active calls. Note:This object is not valid for Synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.11.1 | RowcallTN3270Entry | not-accessible | deprecated | Call's TN3270 parameters. |
| 1.3.6.1.4.1.15.2.12.1.11.1.1 | ColumncallTN3270LineIdx | read-only | deprecated | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.11.1.2 | ColumncallTN3270Idx | read-only | deprecated | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.11.1.3 | ColumncallTN3270PrinterHost | read-only | deprecated | The IP address of the machine running a Berkeley-style lpd server. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'tn3270_printer_n… |
| 1.3.6.1.4.1.15.2.12.1.11.1.4 | ColumncallTN3270PrinterName | read-only | deprecated | A valid printer name contained in the /etc/printcap file on the remote host. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'tn3270… |
| 1.3.6.1.4.1.15.2.12.1.12 | TablecallLATTable | not-accessible | deprecated | Table of entries of LAT parameters for active calls. Note:This object is not valid for synchronous ports. |
| 1.3.6.1.4.1.15.2.12.1.12.1 | RowcallLATEntry | not-accessible | deprecated | Call's LAT parameters. |
| 1.3.6.1.4.1.15.2.12.1.12.1.1 | ColumncallLATLineIdx | read-only | deprecated | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.12.1.2 | ColumncallLATIdx | read-only | deprecated | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.12.1.3 | ColumncallLATAuthMap | read-only | deprecated | The syntax of this object is an octet string 32 bytes long, with the first byte representing groups 0 through 7 and the last byte representing groups 248 throu… |
| 1.3.6.1.4.1.15.2.12.1.12.1.4 | ColumncallLATbEnable | read-only | deprecated | Controls interpretation of LAT Data-B packets received from host. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'latb_enable'. |
| 1.3.6.1.4.1.15.2.12.1.12.1.5 | ColumncallLATMultiSession | read-only | deprecated | This parameter allows multisession operation to be managed on a per port basis. If multisessions for the server has not been enabled, any attempt to use this c… |
| 1.3.6.1.4.1.15.2.12.1.13 | TablecallSetupTable | not-accessible | deprecated | Table of entries of call setup information active calls. |
| 1.3.6.1.4.1.15.2.12.1.13.1 | RowcallSetupEntry | not-accessible | deprecated | Call's Setup information parameters. |
| 1.3.6.1.4.1.15.2.12.1.13.1.1 | ColumncallSetupLineIdx | read-only | deprecated | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.12.1.13.1.2 | ColumncallSetupIdx | read-only | deprecated | A call's B channel number ranging from 1-30. |
| 1.3.6.1.4.1.15.2.12.1.13.1.3 | ColumncallSetupPortType | read-only | deprecated | A enumerated integer indicating the port type. Detecting(4) means the annex is in the process of detecting the port type. |
| 1.3.6.1.4.1.15.2.12.1.13.1.4 | ColumncallSetupCallType | read-only | deprecated | This object returns the whether the call is incoming or outgoing. |
| 1.3.6.1.4.1.15.2.12.1.13.1.5 | ColumncallSetupCallingTime | read-only | deprecated | This object returns the time the call has been in progress. Measured in seconds |
| 1.3.6.1.4.1.15.2.12.1.13.1.6 | ColumncallSetupCallingNbr | read-only | deprecated | This object returns the calling number. |
| 1.3.6.1.4.1.15.2.12.1.13.1.7 | ColumncallSetupCalledNbr | read-only | deprecated | This object returns the number called. |
| 1.3.6.1.4.1.15.2.12.1.13.1.8 | ColumncallSetupCalledSubAddr | read-only | deprecated | This object returns called party subaddress. |
| 1.3.6.1.4.1.15.2.12.1.13.1.9 | ColumncallSetupBearer | read-only | deprecated | This object defines the bearer capability of the incoing call. Possible values are voice and data. |
| 1.3.6.1.4.1.15.2.12.1.13.1.10 | ColumncallSetupPortNumber | read-only | deprecated | This object returns the port number the call is assigned to. This object in conjunction with the object, port type, should be used to cross-reference the infor… |
| 1.3.6.1.4.1.15.2.12.2 | Nodeglobals | |||
| 1.3.6.1.4.1.15.2.12.2.1 | ScalargpGenericMode | read-write | mandatory | This parameter defines the mode for access to the serial line or TA port. The default is cli. This MIB object corresponds to the NA/admin asynchronous,ta, sync… |
| 1.3.6.1.4.1.15.2.12.2.2 | ScalargpGenericLocation | read-write | mandatory | A descriptive string for a this port. This string is displayed by the CLI who command. This MIB object corresponds to the NA/admin asynchronous, ta, synchronou… |
| 1.3.6.1.4.1.15.2.12.2.3 | ScalargpGenericTermVar | read-write | mandatory | A string defining the type of terminal attached to the serial/ta port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'term_var'. N… |
| 1.3.6.1.4.1.15.2.12.2.4 | ScalargpGenericPrompt | read-write | mandatory | This parameter defines a port-specific prompt string. The prompt string consists of displayable characters and embedded formatting codes. Each formatting code … |
| 1.3.6.1.4.1.15.2.12.2.5 | ScalargpGenericCliInterface | read-write | deprecated | Specifies either a Unix or VMS command line interface. The default is uci. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'cli_inte… |
| 1.3.6.1.4.1.15.2.12.2.6 | ScalargpGenericAllowBcast | read-write | mandatory | Controls whether the serial/ta port can receive administrative broadcast messages. This MIB object corresponds to the NA/admin asynchronous/ta port parameter '… |
| 1.3.6.1.4.1.15.2.12.2.7 | ScalargpGenericBcastDirection | read-write | mandatory | Defines the direction that an administrative broadcast message is sent. This parameter is valid only when the port is defined as a slave port by the anxpMode p… |
| 1.3.6.1.4.1.15.2.12.2.8 | ScalargpGenericImask7Bits | read-write | mandatory | When enabled, instructs the Annex to ignore the eighth bit of all received characters on the port. This MIB object corresponds to the NA/admin asynchronous/ta … |
| 1.3.6.1.4.1.15.2.12.2.9 | ScalargpGenericCliImask7 | read-write | mandatory | Defines whether input at the CLI is masked to 7 bits. The default is disabled. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'cli_… |
| 1.3.6.1.4.1.15.2.12.2.10 | ScalargpGenericBanner | read-write | mandatory | Specifies whether the Annex banner and message- of-the-day are displayed on the port. The default is enabled. This has four possible actions: default, Y, yes, … |
| 1.3.6.1.4.1.15.2.12.2.11 | ScalargpGenericTcpKeepAlive | read-write | mandatory | The default keep-alive value for connections to this serial port. If this is zero, use the value specified by anxTcpKeepAlive. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.2.12 | ScalargpGenericDedicatedArgs | read-write | mandatory | Command line arguments to be passed to process started by a dedicated port with mode set to 'telnet', 'tn3270', 'rlogin', 'connect' (if LAT is in use) or 'call… |
| 1.3.6.1.4.1.15.2.12.2.13 | ScalargpGenericModemVar | read-write | mandatory | A string defining the type of modem attached to the serial port. This object is not valid for TA ports. This MIB object corresponds to the NA/admin asynchronou… |
| 1.3.6.1.4.1.15.2.12.2.14 | ScalargpGenericDefSessMode | read-write | mandatory | The default session mode when the DECServer command interface is configured. The default is interactive. This MIB object corresponds to the NA/admin asynchrono… |
| 1.3.6.1.4.1.15.2.12.2.15 | ScalargpGenericResolveProtocol | read-write | mandatory | Default host protocol to use when starting a dedicated port and the protocol is not explicitly specified in the command. Is set to one of 'telnet', connect, or… |
| 1.3.6.1.4.1.15.2.12.2.17 | ScalargpSignalInputStartChar | read-write | mandatory | The control character sequence that restarts input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be ei… |
| 1.3.6.1.4.1.15.2.12.2.18 | ScalargpSignalInputStopChar | read-write | mandatory | The control character sequence that stops input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be eithe… |
| 1.3.6.1.4.1.15.2.12.2.19 | ScalargpSignalOutputStartChar | read-write | mandatory | The control character sequence that restarts output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be … |
| 1.3.6.1.4.1.15.2.12.2.20 | ScalargpSignalOutputStopChar | read-write | mandatory | The control character sequence that stops output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. This value of this object can be eit… |
| 1.3.6.1.4.1.15.2.12.2.21 | ScalargpSignalIxanyFlowCtrl | read-write | mandatory | This parameter specifies whether any input character will be treated as a start (xon) character when output has been suspended by a stop (xoff) character. This… |
| 1.3.6.1.4.1.15.2.12.2.23 | ScalargpSignalForwardKey | read-write | mandatory | Defines a control character sequence as an attention character to switch the user to the next session. The Annex-II only allows a single control character (eg.… |
| 1.3.6.1.4.1.15.2.12.2.24 | ScalargpSignalBackwardKey | read-write | mandatory | Defines a control character sequence as an attention character to switch the user to the previous session. The Annex-II only allows a single control character … |
| 1.3.6.1.4.1.15.2.12.2.30 | ScalargpLoginVciLoginPortPasswd | read-write | deprecated | Enables the port password if the port is configured as a DECServer interface port. The default is disabled. This MIB object corresponds to the NA/admin asynchr… |
| 1.3.6.1.4.1.15.2.12.2.31 | ScalargpLoginVciLoginTimeout | read-write | deprecated | Enables a login timer if the port is configured as a DECServer interface port. The default is disabled. This MIB object corresponds to the NA/admin asynchronou… |
| 1.3.6.1.4.1.15.2.12.2.32 | ScalargpTimerForwardTimer | read-write | mandatory | This parameter defines the inter-character timer that sets the amount of time, in tens of milliseconds, that will elapse before forwarding the received data. T… |
| 1.3.6.1.4.1.15.2.12.2.33 | ScalargpTimerForwardCount | read-write | mandatory | Specifies the number of received characters buffered for the port by the Annex before forwarding the characters to the host or network. This MIB object corresp… |
| 1.3.6.1.4.1.15.2.12.2.34 | ScalargpTimerCliInactivity | read-write | mandatory | The amount of time, in minutes, that the Annex waits before hanging up the serial/ta port after it becomes idle. A value of 0 turns off the timer. A value of 2… |
| 1.3.6.1.4.1.15.2.12.2.35 | ScalargpTimerInactivityTimer | read-write | mandatory | The amount of time, in minutes, which a port can remain inactive before the Annex terminates all sessions and resets the port. A value of 0 disables the timer.… |
| 1.3.6.1.4.1.15.2.12.2.36 | ScalargpTimerInputIsActivity | read-write | mandatory | Controls whether received input characters are considered as activity for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter … |
| 1.3.6.1.4.1.15.2.12.2.37 | ScalargpTimerOutputIsActivity | read-write | mandatory | Controls whether transmitted output characters are considered as activity for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parame… |
| 1.3.6.1.4.1.15.2.12.2.38 | ScalargpTimerResetIdleTimer | read-write | mandatory | Defines whether input or output resets the idle timer for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'reset_idle_time… |
| 1.3.6.1.4.1.15.2.12.2.39 | ScalargpTimerLongBreak | read-write | mandatory | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break greater than two seconds. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.2.40 | ScalargpTimerShortBreak | read-write | mandatory | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break shorter than two seconds. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.12.2.41 | ScalargpSecurityUserName | read-write | mandatory | A string defining the default user name for the user of this serial/ta port. This MIB object corresponds to the NA/admin asynchronous/ta/sync port parameter 'u… |
| 1.3.6.1.4.1.15.2.12.2.42 | ScalargpSecurityCli | read-write | mandatory | This parameter controls whether security is enabled for the port. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'cli_security'. |
| 1.3.6.1.4.1.15.2.12.2.43 | ScalargpSecurityConnect | read-write | mandatory | This parameter controls whether the host-based security policy is enabled for access from the port to the network. This MIB object corresponds to the NA/admin … |
| 1.3.6.1.4.1.15.2.12.2.44 | ScalargpSecurityPortServer | read-write | mandatory | This parameter controls whether the host-based security policy is enabled for access to the port from the port server. This MIB object corresponds to the NA/ad… |
| 1.3.6.1.4.1.15.2.12.2.45 | ScalargpSecurityPortPasswd | read-write | mandatory | This parameter defines a password for the port for local password protection. This MIB object corresponds to the NA/admin asynchronous/ta/sync port parameter '… |
| 1.3.6.1.4.1.15.2.12.2.46 | ScalargpSecurityIpsoClass | read-write | mandatory | Defines the IP security classification for packets sent and received on this port. The default value is none. This MIB object corresponds to the NA/admin async… |
| 1.3.6.1.4.1.15.2.12.2.47 | ScalargpSecurityIpx | read-write | mandatory | Controls whether IPX security is enabled on this port. The default is disabled. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'ipx… |
| 1.3.6.1.4.1.15.2.12.2.48 | ScalargpLineEditAttnChar | read-write | mandatory | Defines a control character sequence as an attention character to return the user to the CLI prompt. The Annex-II only allows x a single control character (eg.… |
| 1.3.6.1.4.1.15.2.12.2.49 | ScalargpLineEditEcho | read-write | mandatory | This parameter controls whether the Annex echoes all characters as they are received from the port. This MIB object corresponds to the NA/admin asynchronous/ta… |
| 1.3.6.1.4.1.15.2.12.2.50 | ScalargpLineEditTelnetEscape | read-write | mandatory | Defines the control character that returns the user to the 'telnet:' prompt when running the CLI telnet command. This value of this object can be either a sing… |
| 1.3.6.1.4.1.15.2.12.2.51 | ScalargpLineEditTelnetCRLF | read-write | mandatory | Defines what characters are transmitted out the port to the network when the End-of-Line character is sensed. 'enabled' means transmit Line-Feed and Carriage-R… |
| 1.3.6.1.4.1.15.2.12.2.52 | ScalargpLineEditMapToLower | read-write | mandatory | When enabled, the Annex translates all upper case characters to lower case as they are received from the port. This MIB object corresponds to the NA/admin asyn… |
| 1.3.6.1.4.1.15.2.12.2.53 | ScalargpLineEditMapToUpper | read-write | mandatory | When enabled, the Annex translates all lower case characters to upper case as they are transmitted to the port. This MIB object corresponds to the NA/admin asy… |
| 1.3.6.1.4.1.15.2.12.2.54 | ScalargpLineEditCharErase | read-write | mandatory | This parameter controls whether the Annex echoes the character erase and word erase characters for a video terminal (enabled) or for a hard-copy terminal (disa… |
| 1.3.6.1.4.1.15.2.12.2.55 | ScalargpLineEditEraseChar | read-write | mandatory | Defines the character erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^… |
| 1.3.6.1.4.1.15.2.12.2.56 | ScalargpLineEditLineErase | read-write | mandatory | This parameter controls whether the Annex echoes the line erase character for a video terminal (enabled) or for a hard-copy terminal (disabled). This MIB objec… |
| 1.3.6.1.4.1.15.2.12.2.57 | ScalargpLineEditEraseLine | read-write | mandatory | Defines the line erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x', w… |
| 1.3.6.1.4.1.15.2.12.2.58 | ScalargpLineEditEraseWord | read-write | mandatory | Defines the word erase control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x', w… |
| 1.3.6.1.4.1.15.2.12.2.59 | ScalargpLineEditHardwareTabs | read-write | mandatory | When enabled, this parameter allows the Annex to expand ASCII tab characters. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'hardw… |
| 1.3.6.1.4.1.15.2.12.2.60 | ScalargpLineEditRedisplayLine | read-write | mandatory | Defines the reprint line control character sequence. This value of this object can be either a single displayable character or two characters of the form '^x',… |
| 1.3.6.1.4.1.15.2.12.2.61 | ScalargpLineEditToggleOutput | read-write | mandatory | Defines the flush control character used to flush the output buffer. This value of this object can be either a single displayable character or two characters o… |
| 1.3.6.1.4.1.15.2.12.2.62 | ScalargpLineEditNewLineTerm | read-write | mandatory | This parameter controls whether a carriage return is echoed as just a carriage return (enabled), or whether the carriage return is echoed as a carriage return … |
| 1.3.6.1.4.1.15.2.12.2.63 | ScalargpNetLocalAddr | read-write | mandatory | The Internet address for the Annex's side of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the NA/admin asynchronous, ta, synchronous p… |
| 1.3.6.1.4.1.15.2.12.2.64 | ScalargpNetRemoteAddr | read-write | deprecated | The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the NA/admin asynchronous, ta, syn… |
| 1.3.6.1.4.1.15.2.12.2.65 | ScalargpNetPppDialupAddr | read-write | mandatory | local(1) - The annex will get the PPP dialup addresses from the port parameters local_address and remote_address. acp(2) - The Annex requests the PPP dialup ad… |
| 1.3.6.1.4.1.15.2.12.2.66 | ScalargpNetMetric | read-write | mandatory | This parameter defines the hop count to the remote end of the SLIP or PPP interface. Setting this object to 0 defaults to a value of 1. This MIB object corresp… |
| 1.3.6.1.4.1.15.2.12.2.67 | ScalargpNetSlipSecure | read-write | mandatory | If anxEnableSecurity is not set, this parameter selects slip session logging. If anxEnableSecurity is set, this parameter permits slip access only from secure … |
| 1.3.6.1.4.1.15.2.12.2.68 | ScalargpNetInactivity | read-write | mandatory | The number of units allowed for serial protocol inactivity on the port. The type of unit, minutes or seconds, is defined by the object anxpNetInactivityUnits. … |
| 1.3.6.1.4.1.15.2.12.2.69 | ScalargpNetDoCompression | read-write | mandatory | When enabled, the Annex will attempt to negotiate TCP/IP header compression on this serial link. This MIB object corresponds to the NA/admin asynchronous/ta/sy… |
| 1.3.6.1.4.1.15.2.12.2.70 | ScalargpNetAllowCompression | read-write | mandatory | When enabled, the Annex will allow TCP/IP header compression on this serial link only if the other end of the serial link initiates the compression. This MIB o… |
| 1.3.6.1.4.1.15.2.12.2.71 | ScalargpNetInactivityUnits | read-write | mandatory | The type of units that are used for the port's net inactivity timer. See also the anxpNetInactivity object. The default value is 'minutes'. This MIB object cor… |
| 1.3.6.1.4.1.15.2.12.2.72 | ScalargpSlipSubnetMask | read-write | mandatory | The subnet mask for this SLIP interface. This MIB object corresponds to the NA/admin asynchronous/ta/sync port parameter 'subnet_mask'. |
| 1.3.6.1.4.1.15.2.12.2.73 | ScalargpSlipMtuSize | read-write | mandatory | Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). The default is large. This MIB … |
| 1.3.6.1.4.1.15.2.12.2.74 | ScalargpSlipNoIcmp | read-write | mandatory | When enabled, the Annex will discard any ICMP packets directed to this SLIP link. This MIB object corresponds to the NA/admin asynchronous/ta/sync port paramet… |
| 1.3.6.1.4.1.15.2.12.2.75 | ScalargpSlipTos | read-write | mandatory | When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic. This MIB object corresponds to the NA/admin asynchronous/ta/syn… |
| 1.3.6.1.4.1.15.2.12.2.76 | ScalargpPPPMru | read-write | mandatory | This parameter defines the maximum receive unit in bytes. The default value is 1500. This MIB object corresponds to the NA/admin asynchronous, ta, and synchron… |
| 1.3.6.1.4.1.15.2.12.2.77 | ScalargpPPPAcm | read-write | mandatory | This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A bit on in the mask indicates th… |
| 1.3.6.1.4.1.15.2.12.2.78 | ScalargpPPPSecurityProto | read-write | mandatory | Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_security (anxEnableSecurity) must… |
| 1.3.6.1.4.1.15.2.12.2.79 | ScalargpPPPRemoteUser | read-write | mandatory | The username used by the Annex to identify itself if the remote PPP peer asks for authentication. This MIB object corresponds to the NA/admin asynchronous/ta/s… |
| 1.3.6.1.4.1.15.2.12.2.80 | ScalargpPPPRemotePasswd | read-write | mandatory | The password used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either <set> if the passwo… |
| 1.3.6.1.4.1.15.2.12.2.81 | ScalargpPPPNcp | read-write | mandatory | A bitmask to set the PPP NCP Options: 0x0001 NCP_ALL 0x0002 NCP_IPCP 0x0004 NCP_ATCP 0x0008 NCP_IPXCP 0x0010 NCP_MP 0x0020 NCP_CCP 0x0040 NCP_CBCP |
| 1.3.6.1.4.1.15.2.12.2.82 | ScalargpPPPIpxNetwork | read-write | mandatory | The IPX network number for an IPX PPP connection using this port. When the IPX PPP connection is established the network number will be negotiated. If one end … |
| 1.3.6.1.4.1.15.2.12.2.83 | ScalargpPPPIpxNode | read-write | mandatory | The IPX node number for an IPX PPP connection using this port. The value of this object is a 12 digit hexadecimal number string representing the IPX node numbe… |
| 1.3.6.1.4.1.15.2.12.2.84 | ScalargpARAPGuest | read-write | deprecated | If enabled, allows ARAP guest login service. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'at_guest'. |
| 1.3.6.1.4.1.15.2.12.2.85 | ScalargpARAPNodeid | read-write | deprecated | The default AppleTalk node ID hint that is used by the Annex on this port. The address consists of two parts separated by a dot. The address may be in either h… |
| 1.3.6.1.4.1.15.2.12.2.86 | ScalargpARAPSecurity | read-write | deprecated | Controls whether ACP service is enabled for this port when establishing an AppleTalk connection. This MIB object corresponds to the NA/admin asynchronous/ta po… |
| 1.3.6.1.4.1.15.2.12.2.87 | ScalargpARAPV42BIS | read-write | deprecated | Controls whether V.42bis compression is done during an ARAP session. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'arap_v42bis'. |
| 1.3.6.1.4.1.15.2.12.2.88 | ScalargpTN3270PrinterHost | read-write | deprecated | The IP address of the machine running a Berkeley-style lpd server. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'tn3270_printer_n… |
| 1.3.6.1.4.1.15.2.12.2.89 | ScalargpTN3270PrinterName | read-write | deprecated | A valid printer name contained in the /etc/printcap file on the remote host. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'tn3270… |
| 1.3.6.1.4.1.15.2.12.2.90 | ScalargpLATAuthMap | read-write | deprecated | This port parameter is functionally identical to anxpLatAuthGroupVal and corresponds to the NA/admin Annex parameter 'group_value'. The syntax of this object i… |
| 1.3.6.1.4.1.15.2.12.2.91 | ScalargpLATbEnable | read-write | deprecated | Controls interpretation of LAT Data-B packets received from host. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'latb_enable'. |
| 1.3.6.1.4.1.15.2.12.2.92 | ScalargpLATMultiSession | read-write | deprecated | This parameter allows multisession operation to be managed on a per port basis. If multisessions for the server has not been enabled, any attempt to use this c… |
| 1.3.6.1.4.1.15.2.12.2.94 | ScalargpcharPortInFlowType | read-write | mandatory | The port's type of input flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON an… |
| 1.3.6.1.4.1.15.2.12.2.95 | ScalargpcharPortOutFlowType | read-write | mandatory | The port's type of output flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON a… |
| 1.3.6.1.4.1.15.2.12.2.96 | ScalargpcharPortSessionMaximum | read-write | mandatory | The maximum number of concurrent sessions allowed on the port. A value of -1 indicates no maximum. Setting the maximum to less than the current number of sessi… |
| 1.3.6.1.4.1.15.2.12.2.97 | Scalargprs232AsyncPortBits | read-write | deprecated | The port's number of bits in a character. This object corresponds to the admin parameter data_bits |
| 1.3.6.1.4.1.15.2.12.2.98 | Scalargprs232AsyncPortStopBits | read-write | deprecated | The port's number of stop bits. This object corresponds to the admin parameter stop_bits |
| 1.3.6.1.4.1.15.2.12.2.99 | Scalargprs232AsyncPortParity | read-write | deprecated | The port's sense of a character parity bit. |
| 1.3.6.1.4.1.15.2.12.2.101 | ScalargpV120Mru | read-write | mandatory | This parameter defines the maximum receive unit in bytes. The default value is 256. This MIB object corresponds to the NA/admin asynchronous, ta, and synchrono… |
| 1.3.6.1.4.1.15.2.12.2.102 | ScalargpMpMrru | read-write | mandatory | This parameter sets the upper limit of the MRRU LCP negotiation. All LCP negotiations will start with this value; negotiation downward only is allowed. The def… |
| 1.3.6.1.4.1.15.2.12.2.103 | ScalargpMpEndPointClass | read-write | mandatory | This parameter sets the preference for the Endpoint Discriminator. PPP Magic Number Block(5) isexcluded; it doesn't guarantee unique link identities and could … |
| 1.3.6.1.4.1.15.2.12.2.104 | ScalargpMpEndPointValue | read-write | mandatory | This parameter sets the value of the Endpoint Discriminator for options that require user-configured information. This parameter is only valid when gpMPEndPoin… |
| 1.3.6.1.4.1.15.2.12.2.105 | ScalargpProxyArpEnable | read-write | mandatory | Specifies whether the Annex will proxy ARP all remote IP connections. A value of enabled(1) will allow the Annex to proxy all remote IP connections. A value of… |
| 1.3.6.1.4.1.15.2.12.2.106 | ScalargpPPPTraceLevel | read-write | mandatory | Controls whether PPP trace messages are sent to the syslog facility or not. The default value is none(0). This MIB object corresponds to the na/admin port para… |
| 1.3.6.1.4.1.15.2.14.1 | TableanxTunnelTable | not-accessible | mandatory | Table of tunnel entries. |
| 1.3.6.1.4.1.15.2.14.1.1 | RowanxTunnelEntry | not-accessible | mandatory | A UDAS Tunnel entry. |
| 1.3.6.1.4.1.15.2.14.1.1.1 | ColumnanxTunnelLineIndex | read-only | mandatory | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is … |
| 1.3.6.1.4.1.15.2.14.1.1.2 | ColumnanxTunnelUnitIndex | read-only | mandatory | On a PRI interface, this is a call's B channel number ranging from 1 to anxt1TotChan. On a port interface, this is the port number ranging from 1 to ports.tota… |
| 1.3.6.1.4.1.15.2.14.1.1.3 | ColumnanxTunnelWanProtocol | read-only | mandatory | This field describes the protocol used on the WAN interface from the Gateway (or Home Agent) to the customer premise equipment (CPE). |
| 1.3.6.1.4.1.15.2.14.1.1.4 | ColumnanxTunnelWanAddress | read-only | mandatory | This field describes the WAN Address from the Gateway (or Home Agent) to the customer premise equipment (CPE). |
| 1.3.6.1.4.1.15.2.14.1.1.5 | ColumnanxTunnelState | read-only | mandatory | This fields describes the Tunnel's current state. reserved - visitor added, authentication in progress pending - authentication complete, registration requisit… |
| 1.3.6.1.4.1.15.2.14.1.1.6 | ColumnanxTunnelMnIPAddress | read-only | mandatory | The IP Address of the Remote Node. |
| 1.3.6.1.4.1.15.2.14.1.1.7 | ColumnanxTunnelMnIPXAddress | read-only | mandatory | The IPX Address of the Remote Node. |
| 1.3.6.1.4.1.15.2.14.1.1.8 | ColumnanxTunnelHaAddress | read-only | mandatory | The IP Address assigned to the Home Agent. |
| 1.3.6.1.4.1.4618.1.2.2.1.1 | Scalarss7Pref1SigGateway | read-write | mandatory | The IP address of the primary SS7 gateway. The default value is 0.0.0.0. This MIB object corresponds to the NA/admin parameter 'pref1_sig_gateway'. |
| 1.3.6.1.4.1.4618.1.2.2.1.2 | Scalarss7Pref2SigGateway | read-write | mandatory | The IP address of the primary secondary SS7 gateway. This may be zero if a redundant SS7 gateway is not available. The default value is 0.0.0.0. This MIB objec… |
| 1.3.6.1.4.1.4618.1.2.2.1.3 | Scalarss7Pref1SigPort | read-write | mandatory | The TCP port number used on the primary SS7 gateway. The default is 1000. This MIB object corresponds to the NA/admin parameter 'pref1_sig_port'. |
| 1.3.6.1.4.1.4618.1.2.2.1.4 | Scalarss7Pref2SigPort | read-write | mandatory | The TCP port number used on the secondary SS7 gateway. The default is 1000. This entry is zero if no redundant SS7 gateway is available. This MIB object corres… |
| 1.3.6.1.4.1.4618.1.2.2.1.5 | Scalarss7SigKeepalive | read-write | mandatory | The maximum time to wait for a packet to be received from SS7 server. This value is in seconds. The default value is 15 seconds. This MIB object corresponds to… |
| 1.3.6.1.4.1.4618.1.2.2.1.6 | Scalarss7CurrentGateway | read-only | mandatory | The address of the current SS7 server. This can change dynamically depending on the state of the server. |
| 1.3.6.1.4.1.4618.1.2.2.1.7 | Scalarss7ConnectionTime | read-only | mandatory | Time at which this connection was established to the current SS7 Gateway. |
| 1.3.6.1.4.1.4618.1.2.2.1.8 | Scalarss7Registration | read-only | mandatory | Describes whether the RAS can accept and/or receive calls. This is set by the ss7 gateway. |
| 1.3.6.1.4.1.4618.1.2.2.1.9 | Tabless7ChanTable | not-accessible | mandatory | Table of ss7 Channel information. |
| 1.3.6.1.4.1.4618.1.2.2.1.9.1 | Rowss7ChanEntry | not-accessible | mandatory | The ss7 channel information. |
| 1.3.6.1.4.1.4618.1.2.2.1.9.1.1 | Columnss7WanIndex | read-only | mandatory | The index value which uniquely identifies the Wan Module. |
| 1.3.6.1.4.1.4618.1.2.2.1.9.1.2 | Columnss7ChanNumber | read-only | mandatory | The index value which uniquely identifies the Channel Numnber. |
| 1.3.6.1.4.1.4618.1.2.2.1.9.1.3 | Columnss7ChanStatus | read-only | mandatory | The status of the ds0 channel. idle(1) - the DS0 is available for calls busy(2) - call is in progress blocked(3) - the RAS of the gateway requested block unblo… |
| 1.3.6.1.4.1.4618.1.2.2.1.9.1.4 | Columnss7ChanState | read-only | mandatory | The state of the ds0 channel. idle(1) - no call in progress connected(2) - call fully established. waitReleaseComplete(3) - waiting for Release Complete from g… |