AirPairv2cTrap-MIB
88 objects
No module-level DESCRIPTION found.
Imported Objects
| AirPair-MIB | airPair ttySessionUserConnectionType ttySessionUserName |
| RFC-1212 | ifIndex OBJECT-TYPE |
| SNMPv2-SMI | IpAddress NOTIFICATION-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.7262.1.26 | NodeapSnmpV2Notification | |||
| 1.3.6.1.4.1.7262.1.26.0 | NodeapSnmpV2Traps | |||
| 1.3.6.1.4.1.7262.1.26.0.0 | NotificationcoldStartV2c | current | A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation … | |
| 1.3.6.1.4.1.7262.1.26.0.1 | NotificationlinkDownV2c | current | A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration. | |
| 1.3.6.1.4.1.7262.1.26.0.2 | NotificationlinkUpV2c | current | A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up. | |
| 1.3.6.1.4.1.7262.1.26.0.3 | NotificationexplicitAuthenticationFailureV2c | current | Authentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty… | |
| 1.3.6.1.4.1.7262.1.26.0.4 | NotificationautoNegotiationDuplexMismatchV2c | current | The AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the switch or router connec… | |
| 1.3.6.1.4.1.7262.1.26.0.5 | NotificationmodemLossOfSignalLockFromDemodulatorV2c | current | Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of acti… | |
| 1.3.6.1.4.1.7262.1.26.0.6 | NotificationmodemUncorrectedBerThresholdExceededV2c | current | The uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radi… | |
| 1.3.6.1.4.1.7262.1.26.0.7 | NotificationmodemModulatorPllLockFailureV2c | current | Modulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the mode… | |
| 1.3.6.1.4.1.7262.1.26.0.8 | NotificationmodemModulatorLossOfSyncBytesV2c | current | Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course… | |
| 1.3.6.1.4.1.7262.1.26.0.9 | NotificationmodemModulatorInputFifoErrorV2c | current | Overrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course… | |
| 1.3.6.1.4.1.7262.1.26.0.10 | NotificationmodemModulatorInputDataErrorV2c | current | All ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action… | |
| 1.3.6.1.4.1.7262.1.26.0.11 | NotificationmodemSnrBelowThresholdV2c | current | The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misali… | |
| 1.3.6.1.4.1.7262.1.26.0.12 | NotificationradioPLDROLostLockV2c | current | The PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is t… | |
| 1.3.6.1.4.1.7262.1.26.0.13 | NotificationradioLostCommunicationV2c | current | RS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recomme… | |
| 1.3.6.1.4.1.7262.1.26.0.14 | NotificationradioMismatchV2c | current | The radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrect… | |
| 1.3.6.1.4.1.7262.1.26.0.15 | NotificationradioPowerAmpV2c | current | The power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit with… | |
| 1.3.6.1.4.1.7262.1.26.0.16 | NotificationifTxSynthUnlockedV2c | current | The IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable caus… | |
| 1.3.6.1.4.1.7262.1.26.0.17 | NotificationifRxSynthUnlockedV2c | current | The IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequen… | |
| 1.3.6.1.4.1.7262.1.26.0.18 | NotificationttySessionCommencedV2c | current | A person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | |
| 1.3.6.1.4.1.7262.1.26.0.19 | NotificationttySessionTerminatedV2c | current | A person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | |
| 1.3.6.1.4.1.7262.1.26.0.20 | NotificationrslBelowThresholdV2c | current | The RSL has been detected below its minimum threshold. | |
| 1.3.6.1.4.1.7262.1.26.0.21 | NotificationdroppedFramesThresholdExceededV2c | current | The ethernet dropped frames threshold has been detected above its threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.22 | NotificationbwUtilizationThresholdExceededV2c | current | The ethernet bandwidth threshold has been detected above its threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.23 | NotificationexplicitAuthFailureClearedV2c | current | The condition has cleared. The peer node is now authenticated. | |
| 1.3.6.1.4.1.7262.1.26.0.24 | NotificationautoNegDuplexMismatchClearedV2c | current | The condition has cleared. The Ethernet connection is not experiencing auto-negotiation duplex mismatch. | |
| 1.3.6.1.4.1.7262.1.26.0.25 | NotificationlossOfSyncSigFromDemoClearedV2c | current | The condition has cleared. The demodulator is synchronized. | |
| 1.3.6.1.4.1.7262.1.26.0.26 | NotificationuncorrectedBerThresExceededClearedV2c | current | The condition has cleared. The demodulator uncorrected BER is now below its minimum threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.27 | NotificationmodemModPLLFailureClearedV2c | current | The condition has cleared. The modem PLL is not failing. | |
| 1.3.6.1.4.1.7262.1.26.0.28 | NotificationmodemModLossOfSyncBytesClearedV2c | current | The condition has cleared. The modem is not experiencing loss of synch bytes. | |
| 1.3.6.1.4.1.7262.1.26.0.29 | NotificationmodemModInputFifoOverUnderClearedV2c | current | The condition has cleared. The modem is not experiencing input FIFO over/under runs. | |
| 1.3.6.1.4.1.7262.1.26.0.30 | NotificationmodemModInputDataInacClearedV2c | current | The condition has cleared. The modem is not experiencing data inactivity. | |
| 1.3.6.1.4.1.7262.1.26.0.31 | NotificationsnrBelowThresholdClearedV2c | current | The condition has cleared. SNR is now above its minimum threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.32 | NotificationradioPLDROLostLockClearedV2c | current | The condition has cleared. The radio PLDRO/LO lost lock condition has cleared. | |
| 1.3.6.1.4.1.7262.1.26.0.33 | NotificationradioLostCommunicationClearedV2c | current | The condition has cleared. RS232 communication has been re-establisted between AIRPAIR and the radio. | |
| 1.3.6.1.4.1.7262.1.26.0.34 | NotificationradioMismatchClearedV2c | current | The condtion has cleared. The radio matches the programmed parameters in the modem. | |
| 1.3.6.1.4.1.7262.1.26.0.35 | NotificationradioPowerAmpClearedV2c | current | The condtion has cleared. The radio Power Amp is not in the failed state. | |
| 1.3.6.1.4.1.7262.1.26.0.36 | NotificationifTxSynthUnlockedClearedV2c | current | The condtion has cleared. The IF stage transmit synthesizer is now locked. | |
| 1.3.6.1.4.1.7262.1.26.0.37 | NotificationifRxSynthUnlockedClearedV2c | current | The condtion has cleared. The IF stage receive synthesizer is now locked. | |
| 1.3.6.1.4.1.7262.1.26.0.38 | NotificationrslBelowThresholdClearedV2c | current | The condition has cleared. RSL is now above its minimum threshold. | |
| 1.3.6.1.4.1.7262.1.26.0.39 | NotificationdroppedFramesThresholdExceededClearedV2c | current | The condition has cleared.The ethernet dropped frames threshold is now below its threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.40 | NotificationbwUtilizationThresholdExceededClearedV2c | current | The condition has cleared. The ethernet bandwidth threshold is now below its threshold value. | |
| 1.3.6.1.4.1.7262.1.26.0.41 | NotificationrxIfCableLossExceededV2c | current | The Rx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split. | |
| 1.3.6.1.4.1.7262.1.26.0.42 | NotificationrxIfCableLossExceededClearedV2c | current | The condition has cleared. The Rx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.43 | NotificationtxIfCableLossExceededV2c | current | The Tx cable loss has exceeded limit. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.44 | NotificationtxIfCableLossExceededClearedV2c | current | The condition has cleared. The Tx cable loss is now within limit. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.45 | Notificationfan1FailedV2c | current | The Fan1 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.46 | Notificationfan1FailedClearedV2c | current | The condition has cleared. The fan1 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.47 | Notificationfan2FailedV2c | current | The Fan2 has failed. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.48 | Notificationfan2FailedClearedV2c | current | The condition has cleared. The fan2 is running normally. This trap is only valid when the AirPair installation type is IDU-ODU split | |
| 1.3.6.1.4.1.7262.1.26.0.49 | NotificationmodemCardMismatchedHardwareFirmwareV2c | current | The modem card has incompatible hardware and firmware. The firmware will not run properly on this card. | |
| 1.3.6.1.4.1.7262.1.26.0.50 | NotificationmodemCardMismatchedHardwareFirmwareClearedV2c | current | The condition has cleared. The modem card has compatible hardware and firmware. The firmware will run properly on this card. | |
| 1.3.6.1.4.1.7262.1.26.0.51 | NotificationatpcConfigMismatchV2c | current | ATPC configuration mismatch in the Airpair systems. ATPC is enabled at one system, but ATPC is not enabled at the other system. | |
| 1.3.6.1.4.1.7262.1.26.0.52 | NotificationatpcConfigMismatchClearedV2c | current | ATPC configuration mismatch in the Airpair systems is cleared. Both systems enabled ATPC. | |
| 1.3.6.1.4.1.7262.1.26.0.53 | NotificationradioHiPwrOptM1V2c | current | When hi-power radio is used, hi-power gate M1 drain current is out of lower or upper limits. | |
| 1.3.6.1.4.1.7262.1.26.0.54 | NotificationradioHiPwrOptM1ClearedV2c | current | When hi-power radio is used, hi-power gate M1 drain current is between lower and upper limits. | |
| 1.3.6.1.4.1.7262.1.26.0.55 | NotificationradioHiPwrOptM2V2c | current | When hi-power radio is used, hi-power gate M2 drain current is out of lower or upper limits. | |
| 1.3.6.1.4.1.7262.1.26.0.56 | NotificationradioHiPwrOptM2ClearedV2c | current | When hi-power radio is used, hi-power gate M2 drain current is between lower and upper limits. | |
| 1.3.6.1.4.1.7262.1.26.0.57 | NotificationradioHiPwrTxDetectorV2c | current | When hi-power radio is used, hi-power tx detector dBm value is smaller than limit. | |
| 1.3.6.1.4.1.7262.1.26.0.58 | NotificationradioHiPwrTxDetectorClearedV2c | current | When hi-power radio is used, hi-power tx detector dBm value is not smaller than limit. | |
| 1.3.6.1.4.1.7262.1.26.0.59 | NotificationsntpServersUnreachableV2c | current | Can't reach any of the sntp servers | |
| 1.3.6.1.4.1.7262.1.26.0.60 | NotificationsntpServersUnreachableClearedV2c | current | At least one of SNTP servers is reachable | |
| 1.3.6.1.4.1.7262.1.26.0.61 | NotificationrlsMismatchV2c | current | RLS mismatch | |
| 1.3.6.1.4.1.7262.1.26.0.62 | NotificationrlsMismatchClearedV2c | current | RLS mismatch cleared | |
| 1.3.6.1.4.1.7262.1.26.0.63 | NotificationrLSShutdownActivatedV2c | current | RLS shutdown is activated | |
| 1.3.6.1.4.1.7262.1.26.0.64 | NotificationrLSShutdownActivatedClearedV2c | current | RLS shutdown is not activated | |
| 1.3.6.1.4.1.7262.1.26.0.65 | NotificationfrequencyFileInvalidV2c | current | When the executing frequency file is invalid, this trap is generated. | |
| 1.3.6.1.4.1.7262.1.26.0.66 | NotificationoptionalParaNotEntFreqFileV2c | current | when the optional parameters are not entered in frequency file, and the system boots up, this trap is generated. | |
| 1.3.6.1.4.1.7262.1.26.0.67 | NotificationprogRadioBandNotFoundFreqFileV2c | current | when the executing frequency file doesn't contain the info related to programmed radio band, this trap is generated. | |
| 1.3.6.1.4.1.7262.1.26.0.68 | NotificationredundancySwitchOverSuccessV2c | current | Radio Redundancy Switch over success | |
| 1.3.6.1.4.1.7262.1.26.0.69 | NotificationredundancySwitchOverFailedV2c | current | Radio Redundancy Switch over failed | |
| 1.3.6.1.4.1.7262.1.26.0.70 | NotificationredundancyNoAtpcSupportV2c | current | Radio does not support atpc | |
| 1.3.6.1.4.1.7262.1.26.0.71 | NotificationredundancyNoAtpcSupportClearedV2c | current | Radio does not support atpc cleared | |
| 1.3.6.1.4.1.7262.1.26.0.72 | NotificationredundancyInvalidFirmwareV2c | current | Radio firmware on radio and on modem card mismatch | |
| 1.3.6.1.4.1.7262.1.26.0.73 | NotificationredundancyInvalidFirmwareClearedV2c | current | Radio firmware mismatch cleared | |
| 1.3.6.1.4.1.7262.1.26.0.74 | NotificationredundancySwitchInitByLocalendV2c | current | Radio switch initiated by local end | |
| 1.3.6.1.4.1.7262.1.26.0.75 | NotificationredundancySwitchInitByPeerV2c | current | Radio switch initiated by peer | |
| 1.3.6.1.4.1.7262.1.26.0.76 | NotificationaamConfigMisMatchV2c | current | Automatic Adaptive modulation configuration mismatch | |
| 1.3.6.1.4.1.7262.1.26.0.77 | NotificationaamConfigMisMatchClearV2c | current | Automatic Adaptive modulation configuration mismatch cleared | |
| 1.3.6.1.4.1.7262.1.26.0.78 | NotificationaamQpskActiveV2c | current | Automatic Adaptive modulation running on QPSK modulation | |
| 1.3.6.1.4.1.7262.1.26.0.79 | NotificationaamQpskActiveClearedV2c | current | Automatic Adaptive modulation running on higher modulation | |
| 1.3.6.1.4.1.7262.1.26.0.80 | NotificationprimaryRadioFaultyV2c | current | Primary radio is faulty. | |
| 1.3.6.1.4.1.7262.1.26.0.81 | NotificationprimaryRadioFaultyClearedV2c | current | primary radio is not faulty anymore. | |
| 1.3.6.1.4.1.7262.1.26.0.82 | NotificationradioSerialNumberMismatchV2c | current | Redundancy, Radio Serial number mismatch. | |
| 1.3.6.1.4.1.7262.1.26.0.83 | NotificationradioSerialNumberMismatchClearedV2c | current | Redundancy, Radio Serial number mismatch cleared. | |
| 1.3.6.1.4.1.7262.1.26.0.84 | NotificationexcessiveCableLossChangeV2c | current | Excessive cable loss change | |
| 1.3.6.1.4.1.7262.1.26.0.85 | NotificationexcessiveCableLossChangeClearedV2c | current | Excessive cable loss change cleared |