NMS510-MIB
59 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.6 | Nodenms510 | |||
| 1.3.6.1.4.1.498.8.6.1 | Scalarnms510MIBversion | read-only | mandatory | Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number… |
| 1.3.6.1.4.1.498.8.6.2 | Tablenms510UnitCfgTable | not-accessible | mandatory | The NMS510 Unit Configuration table. This table augments the GDC SC5520 Unit Configuration table, providing unit level configuration for each NMS510 device ins… |
| 1.3.6.1.4.1.498.8.6.2.1 | Rownms510UnitCfgEntry | not-accessible | mandatory | The NMS510 Unit Configuration table entry. The information in this entry augments the information in the corresponding entry in the GDC SC Unit Configuration t… |
| 1.3.6.1.4.1.498.8.6.2.1.1 | Columnnms510UnitCfgIndex | read-only | mandatory | The index value which uniquely identifies the NMS510 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.6.2.1.2 | Columnnms510DteCtsDelay | read-write | mandatory | RTS/CTS Delay options ctsOn(1) Forces both RTS and CTS On regardless of the state of the attached business equipment (the transmitter is On regardless of the s… |
| 1.3.6.1.4.1.498.8.6.2.1.3 | Columnnms510DteCtsDelayExt | read-write | mandatory | RTS/CTS Delay options extension ext0mSec(1) Used to enable options cts0mSec(2) or ctsFix3Char(3) from MIB object nms510DteCtsDelay. ext30mSec(2) Provides 30 ms… |
| 1.3.6.1.4.1.498.8.6.2.1.4 | Columnnms510FirmwareLevel | read-only | mandatory | |
| 1.3.6.1.4.1.498.8.6.2.1.5 | Columnnms510AlarmCfgCountWindow | read-write | mandatory | The DDS Alarm Threshold Alarm Interval. It specifies the amount of time in minutes, 1 to 15 minutes, in which the threshold setting is to be exceeded for the a… |
| 1.3.6.1.4.1.498.8.6.2.1.6 | Columnnms510SoftReset | read-write | mandatory | This object will cause software reset in dataset. |
| 1.3.6.1.4.1.498.8.6.2.1.7 | Columnnms510FrontPanelInhibit | read-write | mandatory | Inhibits front panel test switch. If a test switch is activated while inhibited it will simply be ignored. If enabled via the nms510FrontPanelEnable object the… |
| 1.3.6.1.4.1.498.8.6.2.1.8 | Columnnms510FrontPanelEnable | read-write | mandatory | Enables front panel test switch. If a test switch is activated while inhibited, via the nms510FrontPanelInhibit object, it will simply be ignored. If enabled t… |
| 1.3.6.1.4.1.498.8.6.2.1.9 | Columnnms510HdlcInvert | read-write | mandatory | Primary data invert option. Will enhance the quality of data when network does not provide B8Z5. Primarily used with DDS II 56k |
| 1.3.6.1.4.1.498.8.6.2.1.10 | Columnnms510PiggyBackDetect | read-only | mandatory | If set to 2 then either a Data Rate Adadaptor or 530 card is installed. |
| 1.3.6.1.4.1.498.8.6.2.1.11 | Columnnms510ExtPortCtrlOut1 | read-write | mandatory | This option sets the external output state (on/off) of the current network element and displays the external output. |
| 1.3.6.1.4.1.498.8.6.2.1.12 | Columnnms510ExtPortCtrlOut2 | read-write | mandatory | This option sets the external output state (on/off) of the current network element and displays the external output. |
| 1.3.6.1.4.1.498.8.6.4 | Nodenms510AlarmData | |||
| 1.3.6.1.4.1.498.8.6.4.1 | Nodenms510NoResponseAlm | |||
| 1.3.6.1.4.1.498.8.6.4.2 | Nodenms510DiagRxErrAlm | |||
| 1.3.6.1.4.1.498.8.6.4.3 | Nodenms510PowerUpAlm | |||
| 1.3.6.1.4.1.498.8.6.4.4 | Nodenms510EEChkSumErrAlm | |||
| 1.3.6.1.4.1.498.8.6.4.5 | Nodenms510StcLoopbackAlm | |||
| 1.3.6.1.4.1.498.8.6.4.6 | Nodenms510NoSignalAlm | |||
| 1.3.6.1.4.1.498.8.6.4.7 | Nodenms510FpTestAlm | |||
| 1.3.6.1.4.1.498.8.6.4.8 | Nodenms510StreamingAlm | |||
| 1.3.6.1.4.1.498.8.6.4.9 | Nodenms510DSRLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.10 | Nodenms510DTRLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.11 | Nodenms510DTPLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.12 | Nodenms510DCDLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.13 | Nodenms510RXDLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.14 | Nodenms510TXDLossAlm | |||
| 1.3.6.1.4.1.498.8.6.4.15 | Nodenms510DBURequestForScanAlm | |||
| 1.3.6.1.4.1.498.8.6.4.16 | Nodenms510DBUOnalm | |||
| 1.3.6.1.4.1.498.8.6.4.17 | Nodenms510DBUFailedAlm | |||
| 1.3.6.1.4.1.498.8.6.4.18 | Nodenms510ExtInputChangeAlm | |||
| 1.3.6.1.4.1.498.8.6.4.19 | Nodenms510ExtInputLowAlm | |||
| 1.3.6.1.4.1.498.8.6.4.20 | Nodenms510FrameLossAlm | |||
| 1.3.6.1.4.1.498.8.6.6 | Tablenms510DiagCfgTable | not-accessible | mandatory | The NMS510 Unit Diagonostic table. |
| 1.3.6.1.4.1.498.8.6.6.1 | Rownms510DiagCfgEntry | not-accessible | mandatory | The NMS510 Unit Diagonostic table entry. |
| 1.3.6.1.4.1.498.8.6.6.1.1 | Columnnms510DiagCfgIndex | read-only | mandatory | The index value which uniquely identifies the NMS510 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.6.6.1.2 | Columnnms510DiagSendCode | read-write | mandatory | Configures the selftest pattern to be run during any diagonostic test involving selftest. If option SendOtherPattern is selected, then pattern will default to … |
| 1.3.6.1.4.1.498.8.6.6.1.3 | Columnnms510DiagTestExceptions | read-only | mandatory | Indicates exceptions that have occurred that may affect interpretation of the test results. The value of this object is a sum. This sum initially take the valu… |
| 1.3.6.1.4.1.498.8.6.6.1.4 | Columnnms510DiagBitErrors | read-only | mandatory | The bit errors of the last diagnostic test that involved a Selftest pattern. Reading bit errors while a diagnostic test in running will cause the unit to drop … |
| 1.3.6.1.4.1.498.8.6.6.1.5 | Columnnms510DiagBlockErrors | read-only | mandatory | The block errors of the last diagnostic test that involved a Selftest pattern. Reading block errors while a diagnostic test in running will cause the unit to d… |
| 1.3.6.1.4.1.498.8.6.6.1.6 | Columnnms510DiagTestReset | read-write | mandatory | This object will halt the execution of any and all diagnostic test that may be running with the exception of the Network Delay Test. This should only be used t… |
| 1.3.6.1.4.1.498.8.6.7 | Tablenms510DiagExcTable | not-accessible | mandatory | The NMS510 Unit Diagonostic table. |
| 1.3.6.1.4.1.498.8.6.7.1 | Rownms510DiagExcEntry | not-accessible | mandatory | The NMS510 Unit Diagonostic table entry. |
| 1.3.6.1.4.1.498.8.6.7.1.1 | Columnnms510DiagExcIndex | read-only | mandatory | The index value which uniquely identifies the NMS510 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.6.7.1.2 | Columnnms510DiagIntLineloop | read-write | mandatory | Lineloop (or Analoop) can be either a Bilaterial or Unilaterial loopback depending on option ddsDteTermaloop. To initiate a Lineloop with Selftest SET this obj… |
| 1.3.6.1.4.1.498.8.6.7.1.3 | Columnnms510DiagIntDataloop | read-write | mandatory | To initiate a Dataloop with Selftest SET this object and specifiy a blocksize. The nms510 (the remote) unit will go into Dataloop and the master (the sc5520) u… |
| 1.3.6.1.4.1.498.8.6.7.1.4 | Columnnms510DiagEndToEndSelftest | read-write | mandatory | To initiate an End to End Selftest(Error Rate Test) SET this object and specifiy a blocksize. Both the remote (nms510) amd master (sc5520) units will go into S… |
| 1.3.6.1.4.1.498.8.6.7.1.5 | Columnnms510DiagNetworkDelay | read-write | mandatory | To initiate a Network Delay test SET this object and specifiy runDelayTest. Both the remote (nms510) and master (sc5520) units will go into a test to measure n… |
| 1.3.6.1.4.1.498.8.6.7.1.6 | Columnnms510DiagTestStatus | read-only | mandatory | This object gives the current diagonostic test status. noTest indicates that no diagonostic test is currently active. Reading this object while in a diagonosti… |
| 1.3.6.1.4.1.498.8.6.7.1.7 | Columnnms510DiagExtDataloop | read-write | mandatory | To initiate a Dataloop test with no Selftest SET this object and specifiy external, this will allow the data from the DTE attached to the far end unit (sc5520)… |
| 1.3.6.1.4.1.498.8.6.8 | Tablenms510AlarmCfgTable | not-accessible | mandatory | The GDC NMS510 Alarm Configuration Table. |
| 1.3.6.1.4.1.498.8.6.8.1 | Rownms510AlarmCfgEntry | not-accessible | mandatory | An entry in the GDC NMS510 alarm Configuration table. |
| 1.3.6.1.4.1.498.8.6.8.1.1 | Columnnms510AlarmCfgIndex | read-only | mandatory | This object is the index of the NMS510 Alarm Threshold Configuration table. |
| 1.3.6.1.4.1.498.8.6.8.1.2 | Columnnms510AlarmCfgIdentifier | read-only | mandatory | The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) do… |
| 1.3.6.1.4.1.498.8.6.8.1.3 | Columnnms510AlarmCfgThreshold | read-write | mandatory | This function sets/reads the alarm threashold settings criteria. This threshold is used along with the alarm window to determine the number of instances in a g… |