SC5520-MIB
98 objects
No module-level DESCRIPTION found.
Imported Objects
| DDS-MIB | dsu |
| GDCMACRO-MIB | SCinstance |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | BEGIN IMPORTS TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.3 | Nodesc5520 | |||
| 1.3.6.1.4.1.498.8.3.1 | Scalarsc5520MIBversion | read-only | mandatory | Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number… |
| 1.3.6.1.4.1.498.8.3.2 | Tablesc5520UnitCfgTable | not-accessible | mandatory | The SC5520 Unit Configuration table. |
| 1.3.6.1.4.1.498.8.3.2.1 | Rowsc5520UnitCfgEntry | not-accessible | mandatory | The SC5520 Unit Configuration table entry. The information in this entry provides unit level configuration for the SC5520. |
| 1.3.6.1.4.1.498.8.3.2.1.1 | Columnsc5520UnitCfgIndex | read-only | mandatory | The index value which uniquely identifies the SC5520 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.3.2.1.2 | Columnsc5520Nms510CompatibilityMode | read-write | mandatory | The NMS510 compatibility mode. This mode allows the SC5520 to behave in a manner compatible with that of the NMS510. If this object has the value enabled(2), t… |
| 1.3.6.1.4.1.498.8.3.2.1.3 | Columnsc5520PtToPtSentryTime | read-write | mandatory | The Point to point sentry time sc5520PtToPtSentryTime, is used to control the amount of time between unsolicited alarm responses from a remote unit in a point … |
| 1.3.6.1.4.1.498.8.3.2.1.4 | Columnsc5520AlarmHystTime | read-write | mandatory | The Alarm hysteresis time sc5520AlarmHystTime, is used to control the amount of time a remote must wait between reporting unsolicited alarm conditions. A remot… |
| 1.3.6.1.4.1.498.8.3.2.1.5 | Columnsc5520MtpointRmRspIntrvl | read-write | mandatory | The multipoint remote response interval sc5520MtpointRmRspIntrvl, is used to control the amount of time between unsolicited alarm responses from a remote unit … |
| 1.3.6.1.4.1.498.8.3.2.1.6 | Columnsc5520DtePortType | read-write | mandatory | The value auto(3), indicates that the DTE port is automatically being detected, and set. The rs232(1), will force the DTE port to EIA/TIA-232-E, and v35(2), wi… |
| 1.3.6.1.4.1.498.8.3.2.1.7 | Columnsc5520DteCtsDelay | read-write | mandatory | RTS/CTS Delay options ctsOn(1) Forces both RTS and CTS On regardless of the state of the attached business equipment (the transmitter is On regardless of the s… |
| 1.3.6.1.4.1.498.8.3.2.1.8 | Columnsc5520DteCtsDelayExt | read-write | mandatory | RTS/CTS Delay options extension ext0mSec(1) Used to enable options cts0mSec(2) or ctsFix3Char(3) from MIB object sc5520DteCtsDelay. ext30mSec(2) Provides 30 ms… |
| 1.3.6.1.4.1.498.8.3.2.1.9 | Columnsc5520BkPlaneFracNum | read-write | mandatory | Configures the unit to direct data to 1 of 32 time slots that exits on each of 4 highways (see sc5520BkPlaneFracIndex). By setting up units to a highway and ti… |
| 1.3.6.1.4.1.498.8.3.2.1.10 | Columnsc5520BkPlaneFracIfIndex | read-write | mandatory | Configures the unit to direct data to 1 of 4 hardware channels (pairs) that exist on the backplane of the management shelf. By seting up units to a highway and… |
| 1.3.6.1.4.1.498.8.3.2.1.11 | Columnsc5520FirmwareLevel | read-only | mandatory | |
| 1.3.6.1.4.1.498.8.3.2.1.12 | Columnsc5520FrontPanelInhibit | read-write | mandatory | Inhibits all front panel test switches. If a test switch is activated while inhibited it will simply be ignored. If enabled via the sc5520FrontPanelEnable obje… |
| 1.3.6.1.4.1.498.8.3.2.1.13 | Columnsc5520FrontPanelEnable | read-write | mandatory | Enables all front panel test switches. If a test switch is activated while inhibited, via the sc5520FrontPanelInhibit object, it will simply be ignored. If ena… |
| 1.3.6.1.4.1.498.8.3.2.1.14 | Columnsc5520RemLoopAllowed | read-write | mandatory | Inhibits or enables a unit from going into remote loop when requested by the far end. |
| 1.3.6.1.4.1.498.8.3.2.1.15 | Columnsc5520RemLoopPattern | read-write | mandatory | Selects the test pattern to be used in a remote loop test. |
| 1.3.6.1.4.1.498.8.3.2.1.16 | Columnsc5520RemLoopTimeout | read-write | mandatory | Inhibits or enables a 10 miniute remote loop test timer. When enabled the remote loop test will be terminated 10 minutes after being initiated. If inhibited th… |
| 1.3.6.1.4.1.498.8.3.2.1.17 | Columnsc5520HdlcInvert | read-write | mandatory | Primary data invert option. Will enhance the quality of data when network does not provide B8Z5. Primarily used with DDS II 56k |
| 1.3.6.1.4.1.498.8.3.2.1.18 | Columnsc5520EIARemLoop | read-write | mandatory | The Remote Loop (RL) EIA test control lead option. This option either allows or blocks EIA initiated test inputs from the DTE interface. The remote unit must s… |
| 1.3.6.1.4.1.498.8.3.2.1.19 | Columnsc5520EIALineLoop | read-write | mandatory | The LT EIA test control lead option. This option either allows or blocks EIA initiated test inputs from the DTE interface. LT (or Analoop) can be either a bila… |
| 1.3.6.1.4.1.498.8.3.2.1.20 | Columnsc5520PiggyBackDetect | read-only | mandatory | If set to 2 then either a Data Rate Adadaptor or 530 card is installed. |
| 1.3.6.1.4.1.498.8.3.2.1.21 | Columnsc5520RateBroadcast | read-write | mandatory | This should only be enabled when adding a remote unit and the Line Type is either DDSII with data rate equal to 56k or 64k Clear Channel. |
| 1.3.6.1.4.1.498.8.3.2.1.22 | Columnsc5520CircuitType | read-write | mandatory | This object defines the circuit type. |
| 1.3.6.1.4.1.498.8.3.2.1.23 | Columnsc5520WakeUpRemote | read-only | mandatory | This object is requested to initiate the add remote process in a point to point circuit. The serial number of the associated remote is returned. |
| 1.3.6.1.4.1.498.8.3.2.1.24 | Columnsc5520ListOfRemotes | read-only | mandatory | A bitwise snapshot of the elements associated with this circuit, the master is always drop zero, the remote in a point to point circuit is always drop one. fir… |
| 1.3.6.1.4.1.498.8.3.2.1.25 | Columnsc5520TelcoLatchingLoop | read-write | mandatory | Inhibits or enables a unit from going into a latching loopback when requested by Telco. |
| 1.3.6.1.4.1.498.8.3.3 | Tablesc5520MasterTable | not-accessible | mandatory | Configure Master with Remote addresses. |
| 1.3.6.1.4.1.498.8.3.3.1 | Rowsc5520MasterTableEntry | not-accessible | mandatory | The SC5520 Mater table entry. A doublely indexed table using the sc5520RemoteSerialNumber object as the second index. |
| 1.3.6.1.4.1.498.8.3.3.1.1 | Columnsc5520MasterIndex | read-only | mandatory | The index value which uniquely identifies the SC5520 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.3.3.1.2 | Columnsc5520AddRemoteAddress | read-write | mandatory | Add Remote address from Master tells the master (SC5520) how many remotes (nms520) units are in its network, the serial number of those remote units and its Dr… |
| 1.3.6.1.4.1.498.8.3.3.1.3 | Columnsc5520DelRemoteAddress | read-write | mandatory | Delete Remote address from Master tells the master (SC5520) how many remotes (nms520) units are in its network, the serial number of those remote units and its… |
| 1.3.6.1.4.1.498.8.3.3.1.4 | Columnsc5520EnableRemoteAlarm | read-write | mandatory | Enable Remote Alarm Control tells the master (SC5520) how to configure the remote units (nms520) in a multipoint configuration with respect to alarm reporting.… |
| 1.3.6.1.4.1.498.8.3.3.1.5 | Columnsc5520DisableRemoteAlarm | read-write | mandatory | Disable Remote Alarm Control tells the master (SC5520) how to configure the remote units (nms520) in a multipoint configuration with respect to alarm reporting… |
| 1.3.6.1.4.1.498.8.3.3.1.6 | Columnsc5520EnableAllRemoteAlarms | read-write | obsolete | Enable All Remote Alarms tells the master (SC5520) how to configure the remote units (nms520) in a multipoint configuration with respect to alarm reporting. Th… |
| 1.3.6.1.4.1.498.8.3.3.1.7 | Columnsc5520DisableAllRemoteAlarms | read-write | obsolete | Disable All Remote Alarms tells the master (SC5520) how to configure the remote units (nms520) in a multipoint configuration with respect to alarm reporting. T… |
| 1.3.6.1.4.1.498.8.3.4 | Nodesc5520AlarmData | |||
| 1.3.6.1.4.1.498.8.3.4.1 | Nodesc5520NoResponseAlm | |||
| 1.3.6.1.4.1.498.8.3.4.2 | Nodesc5520DiagRxErrAlm | |||
| 1.3.6.1.4.1.498.8.3.4.3 | Nodesc5520PowerUpAlm | |||
| 1.3.6.1.4.1.498.8.3.4.4 | Nodesc5520EEChkSumErrAlm | |||
| 1.3.6.1.4.1.498.8.3.4.5 | Nodesc5520FpTestAlm | |||
| 1.3.6.1.4.1.498.8.3.4.7 | Nodesc5520DSRLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.8 | Nodesc5520DTRLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.9 | Nodesc5520DTPLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.10 | Nodesc5520DCDLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.11 | Nodesc5520RXDLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.12 | Nodesc5520TXDLossAlm | |||
| 1.3.6.1.4.1.498.8.3.4.13 | Nodesc5520TmShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.14 | Nodesc5520DcdShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.15 | Nodesc5520DsrShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.16 | Nodesc5520CtsShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.17 | Nodesc5520RxdShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.18 | Nodesc5520RxcShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.19 | Nodesc5520TxcShortedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.20 | Nodesc5520DBURequestForScanAlm | |||
| 1.3.6.1.4.1.498.8.3.4.21 | Nodesc5520DBUOnAlm | |||
| 1.3.6.1.4.1.498.8.3.4.22 | Nodesc5520DBUFailedAlm | |||
| 1.3.6.1.4.1.498.8.3.4.23 | Nodesc5520CSULoopbackAlm | |||
| 1.3.6.1.4.1.498.8.3.5 | Tablesc5520MaintTable | not-accessible | mandatory | The table describes the maintenance functions for the SC5520. |
| 1.3.6.1.4.1.498.8.3.5.1 | Rowsc5520MaintEntry | not-accessible | mandatory | An entry in the GDC maintenance Table |
| 1.3.6.1.4.1.498.8.3.5.1.1 | Columnsc5520MaintIndex | read-only | mandatory | The index value which uniquely identifies the SC5520 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.3.5.1.2 | Columnsc5520LedStatus | read-only | mandatory | Returns a bitwise snapshot of the front panel LED state. Octet 1 bit 7 - not used bit 6 - ON bit 5 - INSV bit 4 - RSP bit 3 - TMG bit 2 - future use bit 1 - fu… |
| 1.3.6.1.4.1.498.8.3.5.1.3 | Columnsc5520SoftReset | read-write | mandatory | This object will cause software reset in dataset. |
| 1.3.6.1.4.1.498.8.3.5.1.4 | Columnsc5520SysUpTime | read-only | mandatory | This variable is used to report the elapsed system tick time for conversion to real time at the controller and is not related to the sysUpTime referenced in MI… |
| 1.3.6.1.4.1.498.8.3.5.1.5 | Columnsc5520PrivateStorage1 | read-write | mandatory | This object is used for general purpose storage. |
| 1.3.6.1.4.1.498.8.3.5.1.6 | Columnsc5520PrivateStorage2 | read-write | mandatory | This object is used for general purpose storage. |
| 1.3.6.1.4.1.498.8.3.5.1.7 | Columnsc5520PrivateStorage3 | read-write | mandatory | This object is used for general purpose storage. |
| 1.3.6.1.4.1.498.8.3.5.1.8 | Columnsc5520BlinkINS | read-write | mandatory | This variable is used to blink the in service (INS) led on the front panel of the sc5520. A get returns the current status of the INS LED - either blinking(2) … |
| 1.3.6.1.4.1.498.8.3.6 | Tablesc5520DiagCfgTable | not-accessible | mandatory | The Diagnostic Configuration Table. |
| 1.3.6.1.4.1.498.8.3.6.1 | Rowsc5520DiagCfgEntry | not-accessible | mandatory | An entry in the GDC DDS Diagnostic Configuration Table. |
| 1.3.6.1.4.1.498.8.3.6.1.1 | Columnsc5520DiagCfgIndex | read-only | mandatory | The index value which uniquely identifies the SC5520 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.3.6.1.2 | Columnsc5520DiagSendCode | read-write | mandatory | Configures the selftest pattern to be run during any diagonostic test involving selftest. If option SendOtherPattern is selected, then pattern will default to … |
| 1.3.6.1.4.1.498.8.3.6.1.3 | Columnsc5520DiagTestExceptions | read-only | mandatory | Indicates exceptions that have occurred that may affect interpretation of the test results. The value of this object is a sum. This sum initially take the valu… |
| 1.3.6.1.4.1.498.8.3.6.1.4 | Columnsc5520DiagBitErrors | read-only | mandatory | The bit errors of the last diagnostic test that involved a Selftest pattern. Reading bit errors while a diagnostic test in running will cause the unit to drop … |
| 1.3.6.1.4.1.498.8.3.6.1.5 | Columnsc5520DiagBlockErrors | read-only | mandatory | The block errors of the last diagnostic test that involved a Selftest pattern. Reading block errors while a diagnostic test in running will cause the unit to d… |
| 1.3.6.1.4.1.498.8.3.6.1.6 | Columnsc5520DiagTestReset | read-write | mandatory | This object will halt the execution of any and all diagnostic test that may be running. |
| 1.3.6.1.4.1.498.8.3.6.1.7 | Columnsc5520DiagTimeDelay | read-only | mandatory | This object reads the results of a Network Delay Test. The results are valid only after the test is completed which takes about 10 seconds. The unit for time d… |
| 1.3.6.1.4.1.498.8.3.7 | Tablesc5520ExcDiagTable | not-accessible | mandatory | The Diagnostic Execution Table. |
| 1.3.6.1.4.1.498.8.3.7.1 | Rowsc5520ExcDiagEntry | not-accessible | mandatory | An entry in the GDC DDS Diagnostic Execution Table. |
| 1.3.6.1.4.1.498.8.3.7.1.1 | Columnsc5520ExcDiagIndex | read-only | mandatory | The index value which uniquely identifies the SC5520 to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, and dro… |
| 1.3.6.1.4.1.498.8.3.7.1.2 | Columnsc5520DiagExtLineloop | read-write | mandatory | Lineloop (or Analoop) can be either a Bilaterial or Unilaterial loopback depending on option ddsDteTermaloop. To initiate a Lineloop with no Selftest SET this … |
| 1.3.6.1.4.1.498.8.3.7.1.3 | Columnsc5520DiagIntLineloop | read-write | mandatory | Lineloop (or Analoop) can be either a Bilaterial or Unilaterial loopback depending on option ddsDteTermaloop. To initiate a Lineloop with Selftest SET this obj… |
| 1.3.6.1.4.1.498.8.3.7.1.4 | Columnsc5520DiagExtDataloop | read-write | mandatory | To initiate a Dataloop test with no Selftest SET this object and specifiy external, this will allow the data from the DTE attached to the far end unit (nms520)… |
| 1.3.6.1.4.1.498.8.3.7.1.5 | Columnsc5520DiagTestStatus | read-only | mandatory | This object gives the current diagonostic test status. noTest indicates that no diagonostic test is currently active. |
| 1.3.6.1.4.1.498.8.3.7.1.6 | Columnsc5520DiagExtRemoteLoop | read-write | mandatory | Point to Point Application only. To initiate a Remoteloop test with no Selftest SET this object and specifiy external. The sc5520 DSE transmitt an in-band comm… |
| 1.3.6.1.4.1.498.8.3.7.1.7 | Columnsc5520DiagRemLoopWithSelf | read-write | mandatory | To initiate a Remoteloop with Selftest SET this object and specifiy a blocksize. The remote unit will go into remoteloop and the master (the sc5520) unit will … |
| 1.3.6.1.4.1.498.8.3.8 | Tablesc5520VersionTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.498.8.3.8.1 | Rowsc5520VersionEntry | not-accessible | mandatory | An entry in the GDC SC5520 Version Table. |
| 1.3.6.1.4.1.498.8.3.8.1.1 | Columnsc5520VersionIndex | read-only | mandatory | Identifies Version parameters associated with the managed object. |
| 1.3.6.1.4.1.498.8.3.8.1.2 | Columnsc5520ActiveFirmwareRev | read-only | mandatory | The version number of the firmware currently executing. The format is MM.NN.BB where: MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision … |
| 1.3.6.1.4.1.498.8.3.8.1.3 | Columnsc5520StoredFirmwareRev | read-only | mandatory | The version number of the firmware stored (in a compressed format) but not currently executing. MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix… |
| 1.3.6.1.4.1.498.8.3.8.1.4 | Columnsc5520BootRev | read-only | mandatory | The version number of the bootstrap firmware. The version number of the firmware, to allow products to know which revision is installed. The released version n… |
| 1.3.6.1.4.1.498.8.3.8.1.5 | Columnsc5520StoredFirmwareStatus | read-only | mandatory | This object represents the state of the Non-Active or Stored firmware: statBlank(1) Factory Default statDownLoading(2) In process of downloading firmware statO… |
| 1.3.6.1.4.1.498.8.3.8.1.6 | Columnsc5520SwitchActiveFirmware | read-write | mandatory | This object is used to switch the active executing firmware from the version in sc5520ActiveRev to the version in sc5520StoredRev. When a switchActive(2) is se… |
| 1.3.6.1.4.1.498.8.3.8.1.7 | Columnsc5520DownloadingMode | read-write | mandatory | This object is used to configure the download mode: disableAll(1) Prevents any firmware downloading to SC5520 enableAndWait(2) Allows downloading zipped code t… |