Wellfleet-RIP6-MIB
73 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.3.16.1.2 | NodewfRipv6Group | |||
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1 | TablewfRipv6IfTable | not-accessible | mandatory | The list of configured RIPv6 interfaces |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1 | RowwfRipv6IfEntry | not-accessible | mandatory | A description of a RIPv6 interface |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.1 | ColumnwfRipv6IntfCreate | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an RIPv6 Interface instance. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.2 | ColumnwfRipv6IntfEnable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a RIPv6 interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.3 | ColumnwfRipv6IntfState | read-only | mandatory | The current state of RIPv6 on this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.4 | ColumnwfRipv6IntfIndex | read-only | mandatory | The index corresponding to the IPv6 interface with the same index to run RIPv6 on. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.5 | ColumnwfRipv6IntfSupply | read-write | mandatory | Transmit RIPv6 packets. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.6 | ColumnwfRipv6IntfListen | read-write | mandatory | Whether to listen to RIPv6 packets |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.7 | ColumnwfRipv6IntfDefaultRouteSupply | read-write | mandatory | Transmit the default route, ::0, in RIPv6 packets. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.8 | ColumnwfRipv6IntfDefaultRouteListen | read-write | mandatory | Receive the default route, ::0, in RIPv6 packets. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.9 | ColumnwfRipv6IntfPoisonedReversed | read-write | mandatory | Specifies how the router advertises routes it has learned from a neighboring router in periodic updates subsequently sent to the neighbor. If 'Poisoned', the n… |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.10 | ColumnwfRipv6IntfBroadcastTimer | read-write | mandatory | This parameter allows the user to configure the frequency of full RIPv6 updates. The default is per the standard. The minimum is every 5 seconds, with a maximu… |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.11 | ColumnwfRipv6IntfTimeoutTimer | read-write | mandatory | This parameter allows the user to configure the time period which RIPv6 will wait before timing out a route. This time is typically 3 x the broadcast timer. Th… |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.12 | ColumnwfRipv6IntfHolddownTimer | read-write | mandatory | This parameter allows the user to configure the time period which unreachable routes will be held in the Routing Pool. This time is typically 3 x the broadcast… |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.13 | ColumnwfRipv6IntfTriggeredUpdates | read-write | mandatory | This parameter allows the user to configure triggered updates. By default this parameter is disabled to conform with previous release action. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.1.1.14 | ColumnwfRipv6IntfDiameter | read-write | mandatory | The Diameter of the RIPv6 network from wfRipv6BaseDiameter. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2 | TablewfRipv6IfStatsTable | not-accessible | mandatory | RIPv6 interface statistics |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1 | RowwfRipv6IfStatsEntry | not-accessible | mandatory | A RIPv6 interface statistics |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.1 | ColumnwfRipv6IfStatsIntfIndex | read-only | mandatory | The Interface Index that this interface runs over |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.2 | ColumnwfRipv6IfStatsInMsgs | read-only | mandatory | The total number of RIPv6 messages received on this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.3 | ColumnwfRipv6IfStatsInRequests | read-only | mandatory | The number of RIPv6 Requests received on this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.4 | ColumnwfRipv6IfStatsInResponses | read-only | mandatory | The number of RIPv6 Responses received on this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.5 | ColumnwfRipv6IfStatsInBadResponses | read-only | mandatory | The number of RIPv6 Pkts received on this interface that were discarded. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.6 | ColumnwfRipv6IfStatsInBadRoutes | read-only | mandatory | The number of RIPv6 RTES received on this interface that were ignored. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.7 | ColumnwfRipv6IfStatsOutMsgs | read-only | mandatory | The total number of RIPv6 messages transmitted on this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.8 | ColumnwfRipv6IfStatsOutRequests | read-only | mandatory | The number of RIPv6 Requests transmitted out this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.9 | ColumnwfRipv6IfStatsOutResponses | read-only | mandatory | The number of RIPv6 Responses sent out this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.10 | ColumnwfRipv6IfStatsOutFullUpdates | read-only | mandatory | The number of RIPv6 Responses sent out this interface that contain a full update of the routing table information. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.11 | ColumnwfRipv6IfStatsOutTriggeredUpdates | read-only | mandatory | The number of RIPv6 Responses sent out this interface that contain incremental updates of the routing table information. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.2.1.12 | ColumnwfRipv6IfStatsOutRoutesAdvertised | read-only | mandatory | The number of RIPv6 Routes advertised out this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3 | NodewfRipv6Log | |||
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.1 | ScalarwfRipv6LogDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete wfRipv6Log mib object. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.2 | ScalarwfRipv6LogDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.3 | ScalarwfRipv6LogLevel | read-write | mandatory | RIP6 log event level. Setting log to a specific level enables logging Ripv6 events of this level and higher. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.4 | ScalarwfRipv6LogEvent | read-write | mandatory | Indicates whether a log message which corresponds to the value of this attributes should be sent to the log. It affects wfRipv6LogCodes only. In order to save … |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.5 | ScalarwfRipv6LogEventDisable | read-write | mandatory | Indicates whether a log event defined in wfRipv6LogEvent is to be logged. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.6 | ScalarwfRipv6LogEvents | read-only | mandatory | Vector of enabled debug messages (to check only). Messages are identified via the string of bits contained within this attribute. The first octet contains bits… |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.3.7 | ScalarwfRipv6LogCfgEvents | read-write | mandatory | User-defined vector of enabled debug messages upon boot. Coded as instance above |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.4 | NodewfRipv6Base | |||
| 1.3.6.1.4.1.18.3.5.3.16.1.2.4.1 | ScalarwfRipv6BaseDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete RIPv6. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.4.2 | ScalarwfRipv6BaseDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable RIPv6. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.4.3 | ScalarwfRipv6BaseState | read-only | mandatory | The current state of the entire RIPv6. |
| 1.3.6.1.4.1.18.3.5.3.16.1.2.4.4 | ScalarwfRipv6BaseDiameter | read-write | mandatory | The Diameter of the RIPv6 network. 1 less than 'infinity |
| 1.3.6.1.4.1.18.3.5.3.16.6.1 | TablewfRip6AcceptTable | not-accessible | mandatory | The Table of Rip6 Accept Policy Rules |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1 | RowwfRip6AcceptEntry | not-accessible | mandatory | An entry in the Rip6 Accept Rule Table |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.1 | ColumnwfRip6AcceptDelete | read-write | mandatory | Create/Delete parameter. |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.2 | ColumnwfRip6AcceptDisable | read-write | mandatory | Enable/Disable parameter. |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.3 | ColumnwfRip6AcceptIndex | read-only | mandatory | Rule index number |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.4 | ColumnwfRip6AcceptName | read-write | mandatory | Rule name - user specified name for this rule |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.5 | ColumnwfRip6AcceptPrefixes | read-write | mandatory | Prefix identification list. This identifies which prefixes will match this rule. If non-null, The octet string contains one or more 3-tuples of this form: firs… |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.6 | ColumnwfRip6AcceptAction | read-write | mandatory | action. 'accept' means that the route should be considered for inclusion in the routing table. 'ignore' means don't consider the route |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.7 | ColumnwfRip6AcceptPreference | read-write | mandatory | preference. This is a metric to be used to compare the route to other routes to the same destination. A value of 15 is 'most preferred'. This parameter only ha… |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.8 | ColumnwfRip6AcceptPrecedence | read-write | mandatory | precedence. This is a metric to be used to compare this policy rule to other rules that a given route may match. A rule with a higher precedence value will be … |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.9 | ColumnwfRip6AcceptInject | read-write | mandatory | prefix injection list. this octet string should only be non-null if the action is 'accept' and if it is desired to insert prefixes into the routing table that … |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.10 | ColumnwfRip6AcceptGateway | read-write | mandatory | RIPv6 gateway list. This octet string contains the addresses of one or more routers that could send RIPv6 updates to this router. If a router address is includ… |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.11 | ColumnwfRip6AcceptInterface | read-write | mandatory | RIPv6 interface list. This octet string contains the addresses of one or more interfaces on this router. If an interface address is included in this list, this… |
| 1.3.6.1.4.1.18.3.5.3.16.6.1.1.12 | ColumnwfRip6AcceptLog | read-write | mandatory | Log Action. If 'true(1), a log event is generated when a prefix matches this filter rule; if 'false(2)', no logging is done. |
| 1.3.6.1.4.1.18.3.5.3.16.6.2 | TablewfRip6AnnounceTable | not-accessible | mandatory | The Table of RIPv6 Announce Route Policy Rules |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1 | RowwfRip6AnnounceEntry | not-accessible | mandatory | An entry in the RIPv6 Announce Rule Table |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.1 | ColumnwfRip6AnnounceDelete | read-write | mandatory | Create/Delete parameter. |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.2 | ColumnwfRip6AnnounceDisable | read-write | mandatory | Enable/Disable parameter. |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.3 | ColumnwfRip6AnnounceIndex | read-only | mandatory | Rule index number |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.4 | ColumnwfRip6AnnounceName | read-write | mandatory | Rule name - user specified name for this rule |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.5 | ColumnwfRip6AnnouncePrefixes | read-write | mandatory | Prefix identification list. This identifies which Prefixes will match this rule. If non-null, The octet string contains one or more 3-tuples of this form: firs… |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.6 | ColumnwfRip6AnnounceAction | read-write | mandatory | action. 'announce' means that the route should be advertised. 'ignore' means don't advertise the route. |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.7 | ColumnwfRip6AnnouncePrecedence | read-write | mandatory | precedence. This is a metric to be used to compare this policy rule to other rules that a given route may match. A rule with a higher precedence value will be … |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.8 | ColumnwfRip6AnnounceRouteSource | read-write | mandatory | route source. This parameter can contain one or more route source identifiers. If the route source is in this bit map, then a route from that source that meets… |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.9 | ColumnwfRip6AnnounceExtRouteSource | read-write | mandatory | external route source. This parameter can contain one or more external route source identifiers. If the external route source is in this bit map, then a route … |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.10 | ColumnwfRip6AnnounceAdvertise | read-write | mandatory | network advertisement list. this octet string should only be non-null if the action is 'announce' and if it is desired to advertise networks that differ from t… |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.11 | ColumnwfRip6AnnounceRipGateway | read-write | mandatory | from RIPv6' gateway list. Only applicable for RIPv6 sourced routes and if RIPv6 is included as a route source. This octet string contains the addresses of one … |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.12 | ColumnwfRip6AnnounceInterface | read-write | mandatory | RIPv6 outbound interface list. This is a list of outgoing RIPv6 interfaces. If an interface appears in this list, the filter applies to RIPv6 advertisements se… |
| 1.3.6.1.4.1.18.3.5.3.16.6.2.1.13 | ColumnwfRip6AnnounceRipMetric | read-write | mandatory | RIPv6 metric. Only valid if the action is 'propagate'. This is an optional export metric to use when advertising a route that matches this filter. If zero, the… |